Advertisement
Quick Links
Nemschoff Palisade 2.0
2 Seat Booth, 1 Seat LSF and RSF Booth
Installation Instructions
How to assemble your 2 seat booth,
1 seat LSF and RSF booth.
Tools Required
Power Drive
Utility Knife
867H-2 Seat Booth
Step 1
(This Step is supposed to be done in the factory but just in case
here is what needs to be done)
1.1 Feel for hole with finger, then carefully cut with sharp utility knife by
using approximate measurement given below.
1.2 Remove fabric from area around bracket mounting hole location, top
bracket mounting locations. Take care not to extend fabric cuts more than
¼ inch from hole center.
Nemschoff for Palisade 2.0
Utility Knife
1-3/4"
7-5/8"
Parts Included
Seat Booth (LSF)
Seat Booth (RSF)
867H-2 Seat Booth
Seat Booth (LSF)
Table Assembly
867H-L Seat Booth
Seat Booth (RSF)
Table Assembly
867H-R Seat Booth
Step 2
2.1 Repeat same for other hole mounting location.
Utility Knife
1-3/4"
7-5/8"
1
1BP8JN rev A
Table Assembly
Back Extension (2 Seat)
Back Extension (RSF)
Back Extension (LSF)
Assembly Instructions
Advertisement
Related Manuals for Nemschoff Palisade 2.0
Summary of Contents for Nemschoff Palisade 2.0
-
Page 1: Installation Instructions
1.2 Remove fabric from area around bracket mounting hole location, top bracket mounting locations. Take care not to extend fabric cuts more than ¼ inch from hole center. Utility Knife 1-3/4” 1-3/4” 7-5/8” 7-5/8” Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions... - Page 2 5.2 Then install the assembly by using 4 flat wahsers and 4 round head machine screws (2” long) at the bottom. Back Extension Assembly Z-Bracket Flat Washer Round head Machine Screw Screw Flat Washer Round head Machine Screw Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...
- Page 3 Take care not to extend fabric cuts more than ¼ inch from hole center. Back Tube Utility Knife Flat Washer 1-3/4” 7-5/8” Round head Machine Screw Round head Machine Screw Flat Washer Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...
- Page 4 5.1 Attach the Z-Bracket by using 4 screws as shown below. 6.1 Attach the L-Bracket on the access panel as shown below. 6.2 Insert set screw into the access panel Z-Bracket Screw Set Screw Screw L-Bracket Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...
- Page 5 1.2 Remove fabric from area around bracket mounting hole location, top bracket mounting locations. Take care not to extend fabric cuts more than ¼ inch from hole center. Utility Knife 1-3/4” 7-5/8” Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...
- Page 6 4.1 Install the back extension by using 4 flat wahsers and 4 round head 5.1 Attach the Z-Bracket by using 4 screws as shown below. machine screws (2” long). Back Extension Z-Bracket Screw Round head Flat Washer Machine Screw Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...
- Page 7 8.1 Install the table assembly by using 6 flat washers and 6 round head machine screws (0.625” long), (4 at the bottom and 2 at the back) as shown below. Table Assembly Flat Washer Round head Machine Screw Round head Machine Screw Flat Washer Nemschoff for Palisade 2.0 1BP8JN rev A Assembly Instructions...