Makita 2702 Manual page 9

OPERATING INSTRUCTIONS
The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as fol-
lows.
CAUTION:
Always unplug the tool before assembly.
Installing saw blade
CAUTION:
• Use the following saw blade. Do not use saw blades which do not comply with the characteristics specified in these
instructions.
For Model
2702
2702x1
2703
2703x1
• Check the arbor hole diameter of the blade before installing the blade. Always use the correct ring for the arbor hole
of the blade you intend to use.
Remove the table insert on the table. Hold the outer flange with the offset wrench 13-22 and loosen the hex nut with
the wrench 19. Then remove the outer flange. (Fig. 1)
Assemble the inner flange, ring, saw blade, outer flange and hex nut onto the arbor, making sure that the teeth of the
blade are pointing down at the front of the table. Always install the hex nut with its recessed side facing the outer
flange. (Fig. 2)
To secure the blade in place, hold the outer flange with the offset wrench 13-22, then tighten the hex nut with the
wrench 19. BE SURE TO TIGHTEN THE HEX NUT SECURELY. (Fig. 3)
Installing blade guard
CAUTION:
Before installing the blade guard, adjust the depth of cut
to its maximum elevation.
Insert the spreader between the blade guard mounting
portion (stay) and the pressure plate. (Fig. 4)
Tighten the hex bolts (A) with the offset wrench 13-22.
The spreader installing location is factory-adjusted so
that the blade and spreader will be in a straight line. How-
ever, if they are not in a straight line, loosen the hex bolts
(B) and adjust the blade guard mounting portion (stay) so
that the spreader is aligned directly behind the blade.
Then tighten the hex bolts (B) to secure the stay. (Fig. 5)
CAUTION:
• Always grasp the striped portion of the offset wrench
when tightening the hex bolts. If you tighten the hex
bolts while grasping the offset wrench further than the
striped portion, the hex bolts may be damaged and/or
an injury to your hand may result.
• If the blade and spreader are not aligned properly, a
dangerous pinching condition may result during opera-
tion. Make sure they are properly aligned.
There must be a clearance of 5 mm or less between the
spreader and the blade teeth. Adjust the spreader
accordingly and tighten the hex bolts (A) securely.
(Fig. 6)
Attach the table insert on the table, then check to see
that the blade guard works smooth.
Max. dia.
210 mm
260 mm
Min. dia. Blade thickness
203 mm 1,4 mm or less
220 mm 1,8 mm or less
Positioning table saw
Locate the table saw in a well lit and level area where you
can maintain good footing and balance. It should be
installed in an area that leaves enough room to easily
handle the size of your workpieces.
The table saw should be secured with four screws or
bolts to the work bench or table saw stand using the
holes provided in the bottom of the table saw. When
securing the table saw on the work bench, make sure
that there is an opening in the top of the work bench the
same size as the opening in the bottom of the table saw
so the sawdust can drop through. If during operation
there is any tendency for the table saw to tip over, slide or
move, the work bench or table saw stand should be
secured to the floor.
NOTE:
Table saw stand Model 2702x1/2703x1 are standard-
equipped with a table saw stand. Leave more than
300 mm clearance between the table and a wall to allow
chip ejection.
Storing accessory (Fig. 7 & 8)
The miter gauge and wrenches can be stored on the left
side of the base and the rip fence can be stored at the
rear of the base.
Adjusting depth of cut (Fig. 9)
The depth of cut may be adjusted by turning the handle.
Turn the handle clockwise to raise the blade or counter-
clockwise to lower it.
Adjusting bevel angle (Fig. 10)
Loosen the lock lever and turn the handwheel until the
desired angle (0° – 45°) is obtained. The bevel angle is
indicated by the arrow pointer. After obtaining the desired
angle, tighten the lock lever to secure the adjustment.
Kerf
1,6 mm or more
2 mm or more
9