Sanyo DVP-P1EX Technical Information page 15
Digital photo printer
Hide thumbs
Also See for DVP-P1EX:
- Instruction manual (56 pages) ,
- Service manual (20 pages) ,
- Instruction manual (56 pages)
Table of Contents
Advertisement
ASSEMBLY NOTES:
1.
Install the "PULLEY,RELAY DRUM
"STOPPER, BELT DRUM
(4G100)
VER, PULLEY
(4G400)
3X0.5
".
Turn the raised side of the "STOPPER,BELT DRUM
(4G300)
" toward the "PULLEY, DRUM
shown in Fig. B of Fig. 3-7-2.
2.
Insert portion A into hole 1 and initially install the "ASSY,
(4G100)
LEVER, PULLEY
2.6X3
(4N000)
" as shown in Fig. A of Fig. 3-7-2.
3.
Referring to Fig. 3-7-3, adjust the pressure welding value
and install the "ASSY,LEVER,PULLEY
follows:
a. Hook the "BELT, DRUM
(4J000)
MOTOR STEP
"SPECIAL SCREW-2.6X8
(4N000)
TPG BIN 2.6X3
stretch tightly.
b. Rotating the "PULLEY, DRUM
rotate the "BELT, DRUM
revolution.
c. Set the Ruler (VJ8-0228) along the "BELT,DRUM
(4I000)
", and confirm that the pressure welding value
is [1.34N±0.29N] when pressing the Dial Tension
Gauge DTN-150G (VJ8-0226) until play in the
"BELT,DRUM
(4I000)
tion and the direction of pressure are shown in Fig. 3-
7-1.
d. If the pressure welding value is not [1.34N±0.29N],
loosen the "SPECIAL SCREW-2.6X8
fine-adjust the "ASSY,LEVER,PULLEY
then re-tighten the "SPECIAL SCREW-2.6X8
(4H000)
". Repeat steps b and c above until the
pressure welding value is within [1.34N±0.29N].
e. Referring to section 3-6, adjust the tension of the
"BELT,MOTOR STEP
Position of measuring tension
ASSY,MOTOR
STEPPING (4K000)
Bending
value 0.5mm
BELT,MOTOR
STEP (4J000)
PULLEY,RELAY DRUM (4G200)
Fig. 3-7-1
(4G200)
" and the
(4G300)
" to the "ASSY, LE-
" with the "SPECIAL WAHSER-
(4F000)
" using the "SCR S-TPG BIN
(4G100)
(4I000)
" and the "BELT,
" on the gears, and tighten the
(4H000)
" and the "SCR S-
" at the point where both belts
(4F000)
" clockwise,
(4I000)
" more than one
" is 1mm. The measuring posi-
(4H000)
" and
(4G100)
(4J000)
".
PULLEY,DRUM
(4F000)
BELT,DRUM (4I000)
Bending value 1mm
" as
" as
Hole 1
ASSY,LEVER,PULLEY
(4G100)
SPECIAL SCREW-2.6X8
(4H000)
STOPPER,BELT
DRUM (4G300)
Turn the raised side toward
the "PULLEY,DRUM (4F000) ".
",
Dial tension gauge
DTN-150G
(VJ8-0226)
Ruler
(VJ8-0228)
BELT,DRUM (4I000)
PULLEY,DRUM (4F000)
–15–
Fig. A
BELT,DRUM (4I000)
SCR S-TPG BIN
2.6X3 (4N000)
PULLEY,RELAY
Portion A
DRUM (4G200)
STOPPER,BELT
DRUM (4G300)
SPECIAL
WAHSER-
SPECIAL
3X0.5
WAHSER-
(4G400)
3X0.5
(4G400)
BELT,MOTOR
STEP (4J000)
Fig. B
Fig. 3-7-2
ASSY,LEVER,PULLEY (4G100)
SPECIAL SCREW-2.6X8
(4H000)
Fig. 3-7-3
Advertisement
Table of Contents
