lancer TouchPoint Installation Manual

Hide thumbs Also See for TouchPoint:

Advertisement

Quick Links

FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations
Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for
immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate
access to other Technical Documents and alternative translations (if available) pertaining to this unit. Contact Lancer
Customer Service for assistance as required.
ABOUT THIS MANUAL
This booklet is an integral and essential part of the product and
should be handed over to the operator after the installation and
preserved for any further consultation that may be necessary.
Please read carefully the guidelines and warnings contained
herein as they are intended to provide the user with essential
information for the continued safe use and maintenance of the
product. In addition, it provides GUIDANCE ONLY to the user on
the correct services and site location of the unit.
The installation and relocation, if necessary, of this product must be carried out by qualified personnel with
up-to-date safety and hygiene knowledge and practical experience, in accordance with current regulations.
IMPORTANT SAFETY INSTRUCTIONS
! Intended Use
The dispenser is for indoor use only. This unit is not a toy. Children should not be supervised not to play with appliance. It should
not be used by children or infirm persons without supervision. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Cleaning and user maintenance
shall not be performed by children without supervision. The min/max ambient operating temperature for the dispenser is 40°F to
105°F (4°C to 41°C). Do not operate unit below minimum ambient operation conditions. Should freezing occur, cease operation of
the unit and contact authorized service technician. Service, cleaning and sanitizing should be accomplished only by trained
personnel. Applicable safety precautions must be observed. Instruction warnings on the product being used must be followed.
! Automatic Agitation
Units are equipped with an automatic agitation system and will activate unexpectedly. Do not place hands or foreign objects in the
ice bin. Unplug the dispenser during servicing, cleaning, and sanitizing. To avoid personal injury, do not attempt to lift the dispenser
without assistance. For heavier dispensers, use a mechanical lift.
4800T
LANCER INSTALLATION GUIDE
BEFORE GETTING STARTED
Each unit is tested under operating conditions and is thoroughly
inspected before shipment. At the time of shipment, the carrier
accepts responsibility for the unit. Upon receiving the unit,
carefully inspect the carton for visible damage. If damage exists,
have the carrier note the damage on the freight bill and file a
claim with carrier. Responsibility for damage to the dispenser lies
with the carrier.
TouchPoint
LANCER PN: 28-0930/03

Advertisement

Table of Contents
loading

Summary of Contents for lancer TouchPoint

  • Page 1 FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate access to other Technical Documents and alternative translations (if available) pertaining to this unit.
  • Page 2: Specifications

    READ THIS MANUAL This manual was developed by the Lancer Corporation as a reference for the owner/operator and installer of this dispenser. Please read this guide before installation and operation of this dispenser. If service is required please call your Lancer Service Agent or Lancer Customer Service.
  • Page 3: Installation

    Lift carton up and off of the unit. NOTE Remove plywood shipping base from unit by moving unit so Lancer does NOT recommend the use of shaved or that one side is off the counter top or table allowing access flake ice in the dispenser.
  • Page 4: Leveling The Dispenser

    An adapter plate is required when installing an icemaker. Contact your Sales Representative or Lancer Customer Service for more information. A bin thermostat is required in order to control the level of ice in the dispenser (Refer to ATTENTION above).
  • Page 5: Installing Remote Syrup Pumps

    Tube to become clogged. Reattach Drip Tray/Cup Rest to unit. Remote Pump Installation If necessary, install water booster (Lancer PN MC-163172) between water supply and the unit. A. Syrup Pump Using tubing cutters, cut water line and install tee fitting, then B.
  • Page 6 Install BIB (bag in box) connectors onto the syrup pump inlet A. CO Regulator tubing. B. 1/4” Nut, Stem & Seal ! ATTENTION C. Line to CO Regulator Manifold Use proper connector for syrup manufacturer D. Oetiker Pliers A. Syrup Pump Inlet C. BIB Connector B.
  • Page 7: Dispenser Setup

    NOTE Prior to plugging in the unit, ensure there are no flash 10. Contact Lancer warranty for the default pass-code or ask the drives insertted in any of the USB ports on CPU store manager if pass code as changed. Reconnect side panels, merchandiser, outer nozzle, splash 11.
  • Page 8: Setting Up Brands

    NOTE Tap the desired syrup brand. Selected brand will become darker. Tap Save to change assignment. Tap Cancel to The pump deck has a 3 minute timeout feature. If the remove selection. timeout occurs, turn the deck OFF then ON by flipping the switch on the control box. 17. Activate the Carb Water module until the carbonator pump comes on. Release the button, allow carbonator to fill and stop.
  • Page 9: Cleaning And Sanitizing

    CLEANING AND SANITIZING GENERAL INFORMATION Lancer equipment (new or reconditioned) is shipped from the factory cleaned and sanitized in accordance with NSF guidelines. The operator of the equipment must provide continuous maintenance as required by this manual and/or state and local health department guidelines to ensure proper operation and sanitation requirements are maintained.
  • Page 10: Every Six Months

    Scheduled Maintenance/Cleaning As Needed • Keep exterior surfaces of unit clean using a clean, damp cloth. • Using the cleaning solution, clean top cover and all exterior stainless steel surfaces. • Clean exterior of dispensing valves and ice chute. • Remove cup rest then clean the drip tray and cup rest.
  • Page 11: Cleaning And Sanitizing Nozzle

    14. Remove the Ice Chute Assembly by removing four (4) While the outer nozzle is in the sanitizing solution, using the screws that secure to unit and set aside. nozzle brush, provided in the installation kit, dip the brush in the sanitizing solution and thoroughly brush the bottom of 15.
  • Page 12: Plumbing Diagram

    PLUMBING DIAGRAM ELECTRONICS DIAGRAM Lancer Corp. 800-729-1500 Technical Support/Warranty: 800-729-1550 custserv@lancercorp.com lancercorp.com...

Table of Contents