Power Connection - Canon VB-R13VE Installation Manual

Specifications
Please refer to the "Appendix – Specifications" for specifications not listed below.
Min. Subject Illumination
Day Mode (color):
0.05 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.002 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
When using the Dome Unit (Smoked) (sold separately)
Day Mode (color):
0.1 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.004 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Day Mode (color):
0.03 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.002 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
When using the Dome Unit (Smoked) (sold separately)
Day Mode (color):
0.06 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.004 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Pan Angle Range 360° continuous panning
Tilt Angle Range 180° (ceiling-mounted position: 0° – 180°)
– When the horizontal direction of the camera is 0°
– When the tilt angle is between angles below, the dome cover can cause a
line to appear in the video, as well as a decline in the video quality
0° – 12° (168° – 180°) (W)
0° – 5° (175° – 180°) (T)
Operating Environment Temperature
(Includes LAN Connector Set Operating Temperature Range (including direct sun exposure):
(Waterproof)) AC: -50°C – +55°C (-58°F – +131°F)
PoE+: -35°C – +55°C (-31°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
Start-up Temperature Range (including direct sun exposure):
AC, PoE+: -30°C – +55°C (-22°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Dimensions ( x H) 229 x 324 mm ( 9.02 x 12.76 in.)
– Camera only
( x H) 229 x 324 mm ( 9.02 x 12.76 in.)
– Camera only (excluding the connector height)
Weight Approx. 3530 g (7.79 lb.)
Approx. 3420 g (7.54 lb.)
Connecting the Camera

Power Connection

Please be sure to read the user manual for the dedicated power supply before use.
Note
• Power supply should conform to all local codes.
• The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.
PoE+/PoE (Power over Ethernet)

Power can be supplied to the camera by using a LAN cable connected to a PoE+/PoE HUB
that conforms to the IEEE802.3at Type 2 (PoE+)/Type 1 (PoE) standard. Use a category 5 or
better LAN cable, 100 m (328 ft.) or less in length.
Important
Check with your dealer for more information about PoE+/PoE HUB and Midspan technology.
•
Midspan (a LAN cable power supply device) is a device that, like a PoE+/PoE HUB,
supplies power to the camera via a LAN cable.
Some PoE+/PoE HUBs allow the limitation of power for each port, but applying limits may
•
interfere with performance. If using this type of PoE+/PoE HUB, do not limit the operating power.
Some PoE+/PoE HUBs have limits for the total power consumption for the ports, which
•
can interfere with performance when multiple ports are in use. In such a case, check the
user manual for your PoE+/PoE HUB.
When the camera is connected to both a PoE+/PoE HUB and an external power supply (12
•
V DC or 24 V AC), power will be supplied in the following order of precedence.
External power supply (24 V AC) > PoE+/PoE HUB > External power supply (12 V DC)
However, when connecting power from both, certain combinations could cause problems
such as unstable network connections. If a problem arises, disable one of the power supplies.
External Power Supply

12 V DC or 24 V AC input can be used. Use the included power interface cable to connect to
the camera power connection terminal.
1
3
1
3
12 V DC can be connected in a non-polar configuration.
Important
The power supply should be within the following voltage range:
•
24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less)
Current supply capacity of at least 2.0 A per camera
12 V DC: Voltage fluctuation within ±10% of 12 V DC
Current supply capacity of at least 1.5 A per camera
• When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 –
1.0 Ω/20 W in series to the power line.
For an external power supply, use a double-insulated device.
•
Recommended Power Cables [Reference]
Cable (AWG)
12 V DC maximum cable length m (ft.)
24 V AC maximum cable length m (ft.)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
© CANON INC. 2019
1: BROWN Power 24 V AC/12 V
DC non-polar
2: BLUE Power 24 V AC/12 V DC
non-polar
3: GREEN FG (frame ground)
24 22 20 18
4 (13.1) 6 (19.7) 10 (32.8) 17 (55.8)
6 (19.7) 10 (32.8) 15 (49.2) 24 (78.7)
AC Adapter

Please use the dedicated AC adapter (sold separately).
Remove the power connector attached to the AC adapter, then connect the power interface cable
included in the package, as shown in the following diagram.
Power Interface
Cable
Power Interface
Cable (Waterproof)
External Device I/O Terminals
External device I/O terminals consist of two input and output systems each. Viewer can be
used to check external device input status and control output to an external device (please
refer to the "Operation Guide").
Use the included I/O interface cable to connect to external device input/output terminals.
1
8
External Device Input Terminals (IN1, IN2)

External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative
terminals connected to the camera interior GND. Connecting 2-wire cable to the positive and
negative terminals and opening or closing the circuit notifies the Viewer.
Important
When connecting sensors and switches, connect terminals that are electrically isolated from
the respective power and GND.
External Device Output Terminals (OUT1, OUT2)

External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets
have no polarity. Controls from the Viewer can be used to open and close the circuit between
the terminals. Using optical couplers, the output terminals are isolated from the camera's
internal circuit.
The load connected to the output terminals should
be within the following rating range.
Rating between output terminals:
Maximum voltage 50 V DC
Continuous load current at or below 100 mA
On resistance: Max. 30 Ω
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker
with an amplifier allows you to send/receive audio through the Viewer.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect to an audio input/output
device.
Audio Input Terminal Common LINE IN/MIC IN (monaural input)

Although the camera has a single audio input system, it supports two types of microphone
input: LINE IN and MIC IN. Before using the audio input, please confirm the [Audio Input] in the
Setting Page (please refer to the "Operation Guide"). LINE IN is selected by default.
Input terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
Dynamic MIC IN
•
Input impedance: 1.5 kΩ ±5%
* Supported microphones: Output impedance: 400 – 600 Ω
• Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 kΩ ±5%
Microphone power supply: plug-in power (voltage: 2.3 V)
* Supported microphones: Condenser microphones with plug-in power support
• LINE IN
Input level: Max. 1 Vp-p
* Use a microphone with an amplifier.
Audio Output Terminal LINE OUT (monaural output)

Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from the
Viewer.
16
Output terminal: 3.5 mm ( 0.14 in.) mini jack (monaural) Output level: Max. 1 Vp-p
26 (85.3)
* Use a speaker with an amplifier.
39 (128.0)
Printed in Japan The contents of this guide are subject to change without any prior notice.
AC Adapter
Brown
Black
White
Blue
Green
Insulate
AC Adapter
Brown
Black
White
Blue
Green
Insulate
1: BROWN External device input 1 IN1 (+)
2: BLACK External device input 1 IN1 (-)
3: RED External device input 2 IN2 (+)
4: BLACK External device input 2 IN2 (-)
5: ORANGE External device output 1 OUT1
6: YELLOW External device output 1 OUT1
7: GREEN External device output 2 OUT2
8: BLUE External device output 2 OUT2
Internal Connection Diagram
10 kΩ 10 kΩ
+3.3 V
1 kΩ
External device Input terminal
IN1 IN2
0.1 µF
External device
Output terminal
OUT1 OUT2