Summary of Contents for ICP IMAT 31IFBI-24VDC
- Page 1 EN-US - english US Instructions for installation and operation Condensate drain ¡MAT 31IFBI-24VDC...
- Page 2 Dear customer, Thank you for deciding in favor of the iMAT 31IFBI-24VDC condensate drain. Please read the installation and operating instructions carefully before mounting and starting up the iMAT 31IFBI-24VDC, and follow our directions. Perfect functioning of the iMAT 31IFBI-24VDC, and thus reliable condensate discharge, can only be guaranteed when the provisions and notes stipulated here are strictly adhered to.
-
Page 3: Table Of Contents
Safety instructions ..........................4 Proper use..............................6 Exclusion from the scope of application....................6 Technical data ............................7 Electrical data............................7 Dimension drawing..........................8 Function..............................9 Installation ............................10 Electrical installation..........................13 Control and maintenance ........................15 Troubleshooting and fault elimination ....................18 Elements and components........................19 Recommended spare parts........................19 iMAT 31IFBI-24VDC... -
Page 4: Pictograms And Symbols
In addition to these operating instructions, local or national regulations must be complied with, if necessary. Make sure that the iMAT 31IFBI-24VDC is operated only within the permissible limit values indicated on the type plate. Any deviation involves a risk for persons and materials, and may result in malfunction and service failures. - Page 5 Regarding the inlet screw joints, excessive tightening forces must be avoided. This applies in particular to conical screw joints. • The iMAT 31IFBI-24VDC will only function when voltage is applied. • Use genuine spare parts only. This is imperative to ensure perfect functioning.
-
Page 6: Proper Use
Pos : 19 /Beko T ec hnis che D okumentati on/Besti mmungsgemäß e Ver wendung/BEKOM AT/Aus schl uß Anwendung BM nic ht für fros tgefähr dete Bereic he (Zusatz) @ 0\mod_1216106439206_15098.doc x @ 15249 @ @ 1 • The iMAT 31IFBI-24VDC is not heatable and, therefore, not suitable for the use in areas where frost is likely to occur. -
Page 7: Technical Data
~ 50 mm (~ 1.97") stripping of cable jacket Recommended ~ 8 mm (~ 0.31 inch) length of the wire end tube Protection class IP 67 Pos : 27 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC... -
Page 8: Dimension Drawing
Pos : 29 /Beko T ec hnis che D okumentati on/Tec hnische D aten/M assz eichnung @ 0\mod_1184569815280_15098.doc x @ 15135 @ @ 1 Pos : 30 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC... -
Page 9: Function
Pos : 32 /Beko T ec hnis che D okumentati on/Funkti on/BEKOMAT/BM IF Ableitfunkti on @ 1\mod_1294307639090_15098.doc x @ 20671 @ @ 1 Via the inlet line (1) the condensate flows into the iMAT 31IFBI-24VDC and accumulates in the housing (2). -
Page 10: Installation
Condensate is subject to mandatory waste disposal. As such, it must be collected in suitable containers, and disposed of or processed properly. Pos : 40 /Beko T ec hnis che D okumentati on/Installati on/BEKOMAT /BM 31/32/33+U+AU (nic ht Vario) Installations hinweise @ 0\mod_1184161640511_15098.doc x @ 15126 @ @ 1 iMAT 31IFBI-24VDC... - Page 11 Install manifold (6) ½" with a slope of 1%. • Introduce the discharge pipe (5) from the top into the manifold (6). • Prior to the start-up, always carry out a leak test and verify the correct engagement of the control unit. iMAT 31IFBI-24VDC...
- Page 12 If the slope in the inlet line is not sufficient or if any other inflow problems occur, a venting line needs to be installed. Pos : 41 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC...
-
Page 13: Electrical Installation
VDE 0100 / IEC 60364 must be provided for. Pos : 44 /Beko T ec hnis che D okumentati on/Installati on/BEKOMAT /Kl emmenbel egung BM 3xU IF @ 9\mod_1409833267739_15098.doc x @ 42000 @ @ 1 iMAT 31IFBI-24VDC... - Page 14 Pos : 45 /Beko T ec hnis che D okumentati on/Installati on/BEKOMAT /E- Schema @ 0\mod_1233758178163_15098.doc x @ 15305 @ @ 1 Electric diagram Pos : 46 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC...
-
Page 15: Control And Maintenance
Exact compliance with the installation- and operation instructions in this manual • Regular maintenance and control of the iMAT in accordance with the instructions in this operating manual Pos : 52 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC... - Page 16 (5) after 8,000 operating hours or max. one year: 1. Remove the control unit (1) by pressing the arresting hook (2). 2. Unfasten the iMAT 31IFBI-24VDC from the outlet (3). 3. Remove the design shell (4) (if there is one) using a screwdriver (10).
- Page 17 • Leak test of the screwed connector • Check of the electrical connections • Check of the correct engagement of the control unit Pos : 55 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC...
-
Page 18: Troubleshooting And Fault Elimination
Circuit board defective empty device Replace the circuit board Service unit defective or dirty Replace the service unit Device blows off continuously Pos : 58 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 iMAT 31IFBI-24VDC... -
Page 19: Elements And Components
Pos : 66 /Beko T ec hnis che D okumentati on/Globale Texte/Hinweis Original anl eitung @ 1\mod_1260433346280_15098.doc x @ 17097 @ @ 1 os: 67 /Beko Technisc he Dokumentation/Gl obal e T exte/Vor behalts kl aus el @ 0\mod_1213704033153_15098.doc x @ 15236 @ @ 1 === Ende der Liste für T extmar ke Inhalt === iMAT 31IFBI-24VDC... - Page 20 Troubleshooting 18 Inlet line 9 Installation 10 Upper part of the cover 19 Installation and operating instructions 4 Installations- und Betriebsanleitung 4 Venting line 12 Instructions, safety instructions 4 Water pocket 12 Lower part of the cover 19 iMAT 31IFBI-24VDC...
- Page 21 31IFBI-24VDC...
- Page 22 31IFBI-24VDC...
- Page 23 31IFBI-24VDC...
- Page 24 Independent Compressor Partners, LLC P.O. Box 206 Jeffersonville, IN 47131 www. compressorpartners.com Translation of the original manual/instructions. Original instructions are in German Subject to technical modifications without notice / errors accepted. ICP_iMAT31_IF_BI_manual_en_us_2014_12. Printed in Germany iMAT 31IFBI-24VDC...