Related Manuals for Honeywell Miller Revolution
Summary of Contents for Honeywell Miller Revolution
- Page 2 Us er In stru ctio ns - Engli sh Thank you for purchasing the Miller Revolution Harness. The Revolution is an all new and totally innovative harness engineered with seven (7) unique components and more than eleven (11) key product features. Your Miller Revolution harness was engineered to meet or exceed all applicable OSHA, ANSI and CSA requirements and standards.
- Page 3 Us er In stru ctio ns - Engli sh Stand Up D-Ring connection. Do not apply lubricants to the spring mechanism. If dirt begins to collect inside the mechanism, use compressed air, a soft brush and/or warm water with a mild detergent to clean it.
- Page 4 Us er In stru ctio ns - Engli sh Donning the Revolution without Belt Hold harness by If leg or chest back D-ring. Shake straps are harness to allow buckled, release all straps to fall in straps and place. unbuckle at this time.
- Page 5 Us er In stru ctio ns - Engli sh Donning the Revolution with Belt Hold harness by If leg or chest back D-ring. Shake straps are harness to allow buckled, release all straps to fall in straps and place. unbuckle at this time.
- Page 6 Us er In stru ctio ns - Engli sh Steps for Ensuring a Snug Fit Adjusting Back D-Ring Pad The upper part D-ring pad (gray mesh) should be located approximately one (1) inch below the neckline. (This should position the back D-ring in between the lower part of the shoulder blades.) Correct adjustment of the back D-ring pad will allow shoul- der strap webbing (and optional pads) to be located further...
-
Page 7: Installing Optional Accessories
Us er In stru ctio ns - Engli sh Installing Optional Accessories Connecting Accessories Identify the green button “8” shaped com- attachment posite attachment point on the clip on the back belt or harness of the accessory. that will be used. - Page 8 Us er In stru ctio ns - Engli sh Installing Shoulder Pads Optional Shoulder Pads Optional harness shoulder pads are available. Please contact your sales person or Miller Customer Service for more information. Installing Shoulder Pads Turn the harness, so that the D-ring is laying up on a flat surface.
- Page 9 Us er In stru ctio ns - Engli sh Installing a Seat Pad Optional Seat Pad An optional harness seat pad is available. Please contact your sales person or Miller Customer Service for more information. Installing Seat Pad Make sure the flat side of the seat pad is facing towards the back of the harness, then at- tatch the two snap straps in the...
-
Page 10: Available Accessories
Us er In stru ctio ns - Engli sh Available Accessories Cell Phone Holders Open End Pliers & Tool Zippered Cylindrical (two sizes) Holder Utility Pouch Multi-pouch Tool Bag Water Bottle Holder Hammer Holder 2 Pocket Nail & Tool Open Bolt and Bull Pin Pouch Bags For more information or to purchase accessories, contact your Miller distributor or Miller Cus-... - Page 11 Us er In stru ctio ns - Engli sh Materials PivotLink: TechWeb: Label Pack: Aluminum, Polyproplyene, Polyester, Nylon Polyproplyene, Santoprene Stainless Steel Stand-up D-Ring Assembly: Pads (Belt, Shoulder, Back): Cam-Buckle: Steel, Stainless Steel, Santoprene Polyester, Nylon Polyester, Nylon and Polyethylene Blend, Nylon NOTES / NOTAS / NOTES...
- Page 12 Toll Free: 800.873.5242 Fax: 800.892.4078 Download this manual at: www.millerfallprotection.com Téléchargez ce manuel à l’adresse: www.millerfallprotection.com Puede bajar por Internet este manual en: www.millerfallprotection.com Honeywell Safety Products P.O. Box 271, 1345 15th Street Franklin, PA 16323 USA...