Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Related Manuals for Sony Trinitron PVM-9045PM
Summary of Contents for Sony Trinitron PVM-9045PM
- Page 1 3-865-341-11 (2) Trinitron ® Color Video Monitor Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. PVM-9045PM © 1998 Sony Corporation (EN)
- Page 2 To prevent fire or shock hazard, do not maintenance is necessary, consult an authorized expose the unit to rain or moisture. Sony dealer. Dangerously high voltages are present inside Ensure that your equipment is connected the unit. Do not open the cabinet. Refer correctly.
- Page 3 As a safety precaution, unplug the unit before cleaning strips). On repacking Retain the original carton and packing materials for safe transport of this unit in the future. If you have any questions about this unit, contact your authorized Sony dealer.
-
Page 4: Table Of Contents
Table of Contents Features ................5 Location and function of parts and controls ............ 6 Front ................... 6 Rear ..................8 Power sources ..............10 Specifications ..............11... -
Page 5: Features
DC 12 V power. The monitor can operate with the blue signal will be displayed. This facilitates the one or two Sony NP-1B* battery packs. If you use the “chroma” and “phase” adjustment, and the observation DC-L10* battery adaptor, the monitor can operate with of the video noise. -
Page 6: Location And Function Of Parts And Controls
Location and Function of Parts and Controls Front 1 Tally lamp 9 DEGAUSS button !º SYNC INT/EXT (sync internal/external) selector !¡ LINE/RGB input selector !™ A/B, RGB/Y R-Y B-Y input selector 2 POWER switch and indicator !£ BLUE ONLY selector 3 VOLUME control 4 CONTR (contrast) control !¢... - Page 7 !º SYNC INT/EXT (sync internal/external) selector !¢ UNDER SCAN selector Keep this button released (INT) to operate the monitor Depress this button for underscanning. The display on the sync signal from the displayed composite video size is reduced by approximately 3% so that four signal.
-
Page 8: Rear
Location and Function of Parts and Controls Rear !• LINE A connectors !ª LINE B connectors @¢ COMPONENT @º REMOTE connector LEVEL selector (8-pin mini DIN) @¡ EXT SYNC (external sync) @∞ RGB/COMPONENT connectors @™ V HOLD (vertical hold) control input connectors @§... - Page 9 Connect to the R-Y/Y/B-Y componenet signal outputs OUT (BNC): Loop-through output of the EXT of a Sony BetaCam video camera. Depress the A/B, SYCN IN connector. Connect to the external sync RGB/Y R-Y B-Y selector on the front panel (Y R-Y B- input of video equipment to be synchronized with this monitor.
-
Page 10: Power Sources
EJECT buttons Note Make sure you disconnect the cables connected to the connectors (AC IN, DC 12 V IN) at the rear of the monitor. Otherwise, the monitor cannot operate on the battery pack(s). NP-1B (not supplied) SONY mark downwards... -
Page 11: Specifications
Specifications Loop-through outputs Video signal Y/C OUT: 4-pin mini DIN connector, 75 ohms terminated Colour system PAL-M, NTSC (75 ohms automatic termination) Resolution 450 TV lines VIDEO OUT: BNC connector, Aperture correction –4.0 dB to +6.0 dB (at 3.0 MHz) 75 ohms terminated (75 ohms Frequency response 6.0 MHz (–3 dB) at all inputs automatic termination) - Page 12 A/B or RGB/Y R-Y B-Y LINE/RGB Notes • For remote control, connect the pin of the desired function to pin 3 (GND). • For remote control, set the front button to OFF (the switch is out). Printed in Japan Sony Corporation...