Options And Peripheral Devices - Mitsubishi Electric FR-F700PJ Series Manual

Options and peripheral devices

List of options
Name
Parameter unit
(Eight languages)
Enclosure surface operation
panel
Parameter unit connection
cable
DIN rail attachment
AC reactor
DC reactor
EMC Directive compliant EMC
filter
EMC filter installation attachment
Radio noise filter
Line noise filter
Filterpack 
Brake resistor
High-duty brake resistor
Brake unit
Resistor unit
Discharging resistor
Power regeneration common
converter
Stand-alone reactor dedicated for
FR-CV
High power factor converter
Surge voltage suppression filter
Manual controller
DC tach. follower
Three speed selector
Motorized speed setter
Ratio setter
PG follower
Master controller
Soft starter
Deviation detector
Preamplifier
Pilot generator
Deviation sensor
Frequency setting
potentiometer
Frequency meter (64mm60mm) YM206NRI 1mA
Calibration resistor
FR Configurator
(Inverter setup software)

A Filterpack (FR-BFP2) is enclosed with the FR-F70PJ-KF inverters.

Rated power consumption.The power supply specifications of the FR series manual controllers and speed controllers are 200VAC 50Hz, 220/220VAC 60Hz,
and 115VAC 60Hz.
Model Applications, Specifications, etc.
FR-PU07
Interactive parameter unit with LCD display
This operation panel enables inverter operation and monitoring of
FR-PA07
frequency, etc. from the enclosure surface
Cable for connection of operation panel or parameter unit  indicates a
FR-CB20
cable length. (1m, 3m, 5m)
FR-UDA01 to 03
Attachment for installation on DIN rail
FR-HAL
For harmonic current reduction and inverter input power factor
improvement
FR-HEL
SF
An EMC filter that complies with the EMC Directive (EN61800-3 C3).
FR-E5NF
FR-A5AT03
An attachment used to mount an EMC compliant EMC filter (SF) to an
FR-AAT02
inverter.
FR-E5T
FR-BIF(H)
For radio noise reduction (connect to the input side)
FR-BSF01
For line noise reduction
FR-BLF
A Filterpack that contains a power factor improving DC reactor,
FR-BFP2
common mode choke, and capacitive filter (radio noise filter) in one.
MRS type,
For increasing the regenerative braking capability (permissible duty
MYS type 3%/6%ED)
For increasing the regenerative braking capability (permissible duty
FR-ABR
10%/ 6%ED)
For increasing the braking capability of the inverter (for high-inertia load
FR-BU2
or negative load)
FR-BR
Brake unit, electrical-discharge resistor and resistor unit are used in
GZG, GRZG type
combination
FR-CV
Unit which can return motor-generated braking energy back to the
FR-CVL power supply in common converter system
The high power factor converter switches the converter section on/off to
reshape an input current waveform into a sine wave, greatly
FR-HC2
suppressing harmonics. (Used in combination with the standard
accessory.)
FR-ASF-H
Filter for suppressing surge voltage on motor
FR-BMF-H
For independent operation. With frequency meter, frequency
FR-AX
potentiometer and start switch.
FR-AL
For synchronous operation (1VA) by external signal (0 to 5V, 0 to 10V DC)
For three speed switching, among high, middle and low speed
FR-AT
operation (1.5VA)
For remote operation. Allows operation to be controlled from several
FR-FK
places (5VA) 
FR-FH
For ratio operation. Allows ratios to be set to five inverters. (3VA)
FR-FP
For tracking operation by a pilot generator (PG) signal (2VA)
Master controller (5VA) for parallel operation of multiple (maximum 35)
FR-FG
inverters. 
For soft start and stop. Enables acceleration/deceleration in parallel
FR-FC
operation (3VA)
For continuous speed control operation. Used in combination with a
FR-FD
deviation sensor or synchro (5VA)
FR-FA
Used as an A/V converter or arithmetic amplifier (3VA)
QVAH-10
For tracking operation. 70V/35VAC 500Hz (at 2500r/min)
For continuous speed control operation (mechanical deviation detection).
YVGC-500W-NS
Output 90VAC/90°
WA2W 1k
For frequency setting. Wire-wound 2W 1k type B characteristic
Dedicated frequency meter (graduated to 130Hz). Moving-coil type DC
ammeter
RV24YN 10k
For frequency meter calibration. Carbon film type B characteristic
FR-SW3-
Supports an inverter startup to maintenance
SETUP-WE



Applicable
Inverter
Applicable for all
models
Applicable for all
models
Applicable for all
models
Applicable for the
3.7K or lower
Applicable for the
certain capacities
Applicable for the
certain capacities
Applicable for the
certain capacities
Applicable for all
models
Applicable for all
models
Applicable for the
certain capacities
200V: Applicable
for the certain
capacities
Applicable for the
certain capacities
Applicable for the
certain capacities
Applicable for the
certain capacities
Applicable for the
certain capacities
400V: Applicable
for the certain
capacities
400V: applicable
for the 5.5K or
higher



Applicable for all
models

59