Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zenith B-9000 Series
Summary of Contents for Zenith B-9000 Series
- Page 2 Zenith Pumps B-9000 ® Gear Pumps Installation, Care and Maintenance Zenith ® Chemical Duty Gear Pumps...
-
Page 3: Specifications
Thoroughly read and understand this entire manual before installation and operation of pump. Zenith ® In 1926, Zenith Pumps was approached Manufacturing techniques were devel- by the synthetic fiber industry to design oped to hold tolerances to ±.00005", a pump that would provide precise,... -
Page 4: Operation
This ensures precise, three moving parts. pulseless and repeatable flow under The B-9000 Series is a new genera- varying process conditions. tion of Zenith’s traditional B-Series pump. Integrated closed loop speed con-... - Page 5 Excessive noise operating conditions. Check with your and vibration can be observed as the Zenith representative to see which 9000- poles of a decoupled magnet move past MD system is appropriate. one another.
- Page 6 Table 1 Note: This sizing procedure should be used as a cc/rev guideline for estimating pump type, pump size 4.29E-06 2.32E-06 and system requirements. Please consult Zenith to 1.93E-06 2.47E-06 confirm pump and system selection prior to placing 1.21E-06 2.77E-06 9.34E-07...
-
Page 7: Installation
If any items During the flush cycle, fluid will pass are missing or damaged, the freight through and around the pump. This carrier and Zenith should be notified will allow the system to be flushed immediately. quickly and effectively. -
Page 8: Cleaning, Inspection
3. Start the pump at the slowest speed pos- sible and, if possible, with a lubricating 4. When satisfactory operation is fluid. Zenith B-9000 pumps must never be achieved, the pump and system can run without a fluid. Watch the point of gradually be brought up to normal discharge for evidence of fluid. - Page 9 Paper towels are not acceptable B-9000 Series Note: As parts are disassembled, place • On the .05 through 2.4 cc/rev models, set screws will have to be...
- Page 10 They new part specifications. Contact may drop, causing damage to the gear Zenith for dimensions. NOTE: .05 teeth. Note that the slip-fit dowels (10) through 2.4 cc/rev models do not may come off with the gear plate.
- Page 11 .05 - 2.4 cc/rev B-9000 Retaining Ring 16 Key 4 Square Key 17 Interpret per Driving Gear 5 19 SHCS M8x1.25 ASME-Y14.5M 1994 Gear Plate 3 7 Rear Plate 9 Arbor Front Plate 8 2 Drive Shaft 6 Driven Gear 10 Hollow Dowel 13 Type 8-IT Mechanical Seal 11 Seal Housing...
- Page 12 15 & 30 cc/rev B-9000 Rear Plate Assembly 7 Retaining Ring 16 Round Key 4 Interpret per Driving Gear 5 20 SHCS M6x1 ASME-Y14.5M 1994 Gear Plate 3 19 SHCS M12X1.75 Grade 12.9 33 Rear Plate Front Plate Assembly 8 34 Sleeve Bearing 9 Arbor Square Key 17...
- Page 13 B-9000 Series Use both pages of the assembly draw- 7. Install the round key (4) into the ing during the reassembly process to keyway on the drive shaft. Assembly assure correct orientation of all parts. 8. Slide the driving gear (5) onto the Considerable care should be taken drive shaft and into the gear plate.
- Page 14 B-9000 Series • Install the ceramic seat into the seal • Install the socket head screws (18) housing (11) with the o-ring of the into the seal housing (11) and tight- Assembly seat away from the mechanical seal. en to the recommended torque.
-
Page 15: Screw Torque
B-9000 Series • Place the larger O-Ring into the 14. Install the square key (17) into the exposed face of the adapter plate. drive shaft keyway. Assembly Lower the barrier cap into position over the inner magnet. If applicable (continued) - Page 16 The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Zenith Pumps and its subsidiaries at any time without notice. ISO 9001: 2000 Registered Zenith Pumps ®...