Panasonic KX-TDE100 Getting Started
Physical cards, pure ip-pbx
Hide thumbs
Also See for KX-TDE100:
- Programming manual (1018 pages) ,
- Pc programming manual (982 pages) ,
- Features manual (470 pages)
Table of Contents
Advertisement
Quick Links
WWW.ERTEBATGROUP.COM
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE100/KX-TDE200: PMMPR Software File Version 7.0000 or later
for Physical Cards
WWW.ERTEBATGROUP.COM
Getting Started
Pure IP-PBX
KX-TDE100
Model No.
KX-TDE200
Advertisement
Table of Contents
Related Manuals for Panasonic KX-TDE100
Summary of Contents for Panasonic KX-TDE100
- Page 1 Physical Cards Pure IP-PBX KX-TDE100 Model No. KX-TDE200 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDE100/KX-TDE200: PMMPR Software File Version 7.0000 or later WWW.ERTEBATGROUP.COM...
-
Page 2: Table Of Contents
Table of Contents WWW.ERTEBATGROUP.COM Table of Contents 1 Before Installation ..................3 Safety Notices ........................4 System Connection Diagram ...................5 Unpacking ..........................6 2 Installation ....................9 Opening/Closing the Front Cover ..................10 Inserting the SD Memory Card to the IPCMPR Card ............11 Installing the Option Units .....................12 Installing the Trunk Cards ....................14 Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16/ CSLC16) ...........................17... -
Page 3: Before Installation
WWW.ERTEBATGROUP.COM Section 1 Before Installation Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... -
Page 4: Safety Notices
1.1 Safety Notices WWW.ERTEBATGROUP.COM 1.1 Safety Notices Please observe the safety notices in this manual in order to avoid danger to users or other people, and prevent damage to property. The notices are classified as follows, according to the severity of injury or damage: WARNING This notice means that misuse could result in death or serious injury. -
Page 5: System Connection Diagram
1.2 System Connection Diagram WWW.ERTEBATGROUP.COM 1.2 System Connection Diagram DLC16 LCOT4 KX-DT346/ KX-DT300/ KX-DT300/ (KX-TDA0172) (KX-TDA0183) KX-DT343/ KX-T7600 KX-T7600 DLC8 Console KX-T7636/ (KX-TDA0171) LCOT16 KX-T7633 DPT (KX-TDA0181) DHLC8 (KX-TDA0170) LCOT8 (KX-TDA0180) CSLC16 CID/PAY8 (KX-TDA0177) (KX-TDA0189) PT-interface CS Voice Wireless Phone CID8 MSLC16 (DHLC only) -
Page 6: Unpacking
Main Unit ´ 1 CD-ROM (including manuals, etc.) ´ 1 ´ 1 Screw A Screw B (Black) AC Cord ´ 3 (KX-TDE100) ´ 2 (KX-TDE100) ´ 4 (KX-TDE200) ´ 6 (KX-TDE200) SD Memory Card ´ 1 Anchor Plug Ferrite Core (for the IPCMPR ´... - Page 7 1.3 Unpacking WWW.ERTEBATGROUP.COM Necessary items (not supplied): ü Telephone cable for extension connection: Diameter of cable Maximum length of cable (ø 0.4 mm to ø 0.6 mm) ø 0.5 mm 1128 m for SLT ø 0.5 mm 720 m for KX-DT300/KX-T7600 series ø...
- Page 8 1.3 Unpacking WWW.ERTEBATGROUP.COM Getting Started for Physical Cards WWW.ERTEBATGROUP.COM...
-
Page 9: Installation
WWW.ERTEBATGROUP.COM Section 2 Installation Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... -
Page 10: Opening/Closing The
2.1 Opening/Closing the Front Cover WWW.ERTEBATGROUP.COM 2.1 Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Turn the screw anticlockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover. -
Page 11: Inserting The Sd Memory Card To The Ipcmpr Card
2.2 Inserting the SD Memory Card to the IPCMPR Card WWW.ERTEBATGROUP.COM 2.2 Inserting the SD Memory Card to the IPCMPR Card The SD Memory Card contains software for all the processes of the PBX and all the customer data. The SD Memory Card must be inserted before startup. Example: KX-TDE200 IPCMPR Card Memory... -
Page 12: Installing The Option Units
2.3 Installing the Option Units WWW.ERTEBATGROUP.COM 2.3 Installing the Option Units Slot Position Install the power supply unit (PSU) into the PSU slot, and optional service cards into free slots. KX-TDE100 KX-TDE200 PSU Slot Null Slot Free Slots IPCMPR Card Null slot is not available for any optional service card. - Page 13 2.3 Installing the Option Units WWW.ERTEBATGROUP.COM Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Back Board Release Lever Screws Guide Rail Installing the Trunk/Extension Cards Insert the card along the guide rails. Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board.
-
Page 14: Installing The Trunk Cards
2.4 Installing the Trunk Cards WWW.ERTEBATGROUP.COM 2.4 Installing the Trunk Cards LCOT4/LCOT8/LCOT16 Card Example: LCOT 16 Card Amphenol To trunk Accessories (included): Screws ´ 2 User-supplied (not included): Amphenol connector Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... - Page 15 2.4 Installing the Trunk Cards WWW.ERTEBATGROUP.COM BRI4/BRI8 Card Example: BRI8 Card To attach the ferrite core RJ45 When using 1 or 2 cables: TX2(-) RX1(-) RX2(+) TX1(+) LINE 1 to LINE 8 When using 3 or 4 cables: To NT1 •...
- Page 16 2.4 Installing the Trunk Cards WWW.ERTEBATGROUP.COM PRI30/PRI23 Card Example: PRI30 Card To attach the ferrite core RJ45 5 cm BNC (TX) To NT1 BNC (RX) To NT1 For RJ45 120Ω 120Ω 75Ω 75Ω For BNC Accessories (included): Ferrite core ´ 1 User-supplied (not included): RJ45 or BNC connectors CAUTION Connect these optional service cards to the trunk through an NT1;...
-
Page 17: Installing The Extension Cards (Dlc8/Dlc16/Dhlc8/Mslc16/Slc8/Slc16/ Cslc16)
2.6 Connecting Extensions WWW.ERTEBATGROUP.COM 2.5 Installing the Extension Cards (DLC8/DLC16/ DHLC8/MSLC16/SLC8/SLC16/CSLC16) Example: DHLC8 Card To attach the ferrite core 3 cm Amphenol To extensions Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note Attach the included ferrite core to the cable. 2.6 Connecting Extensions Example: KX-T7600 Series DPT Pin Assignments... -
Page 18: Frame Earth Connection
2.7 Frame Earth Connection WWW.ERTEBATGROUP.COM 2.7 Frame Earth Connection Loosen the screw. Screw Insert an earthing wire (user-supplied). Tighten the screw. Connect the earthing wire to earth. Earthing wire To earth WARNING • Proper earthing (connection to earth) is very important to reduce the risk to the user of electrocution or to protect the PBX from the bad effects of external noise in the case of a lightning strike. -
Page 19: Before Programming
WWW.ERTEBATGROUP.COM Section 3 Before Programming Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... -
Page 20: Starting The Pbx
3.1 Starting the PBX WWW.ERTEBATGROUP.COM 3.1 Starting the PBX CAUTION • Use only the AC power cord included with the PBX for the PSU. • Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing an earthing strap. •... -
Page 21: Connecting The Pc
3.2 Connecting the PC WWW.ERTEBATGROUP.COM 3.2 Connecting the PC The Maintenance Console serves as an overall system programming tool for the PBX. The Maintenance Console’s Quick Setup lets you easily configure the PBX to receive intercom and trunk calls, as well as apply basic settings such as time and date. -
Page 22: Installing The Maintenance Console
3.3 Installing the Maintenance Console WWW.ERTEBATGROUP.COM 3.3 Installing the Maintenance Console For the system requirements of the PC (e.g., operating system, hardware specifications), refer to "4.3.1 Installing and Starting the Maintenance Console" in the Installation Manual. Note • Make sure to install and use the latest version of the Maintenance Console. •... -
Page 23: Programming
WWW.ERTEBATGROUP.COM Section 4 Programming Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... -
Page 24: Programming The Pbx
Click OK to close this window. Enter the Installer Level Programmer Code (default: INSTALLER). Click OK. Click Connect. Select KX-TDE100/200 from PBX Model. Select the LAN or RS-232C tab, depending on the type of PC connection with the PBX. Specify the settings as required. Note When connecting to the PBX for the first time selecting LAN, the IP Address and Port Number must be set to 192.168.0.101 and 35300 respectively. - Page 25 4.1 Programming the PBX WWW.ERTEBATGROUP.COM Assigning the BRI Setting (Automatic Configuration) Under Configuration, click Slot. Move the mouse pointer over the BRI card. A menu will be shown under the mouse pointer. Click Ous to set the card to out-of-service status. Click Tool ®...
- Page 26 4.1 Programming the PBX WWW.ERTEBATGROUP.COM Assigning the Incoming Trunk Call Destination For analogue trunk users (DIL Setting): Under CO & Incoming Call, click DIL Table & Port Settings. Confirm that the DIL tab is selected. Configure the settings as required. Click OK.
- Page 27 4.1 Programming the PBX WWW.ERTEBATGROUP.COM Setting an Extension Port to Use a DSS Console Under Configuration, click Slot. Move the mouse pointer over the desired extension card to display the menu of options. Click Ous to set the card to out-of-service status. Move the mouse pointer over the card again, then click Port Property.
- Page 28 4.1 Programming the PBX WWW.ERTEBATGROUP.COM Getting Started for Physical Cards WWW.ERTEBATGROUP.COM...
-
Page 29: Confirming The Connection
WWW.ERTEBATGROUP.COM Section 5 Confirming the Connection Getting Started for Physical Cards WWW.ERTEBATGROUP.COM... -
Page 30: Making And Receiving Calls
5.1 Making and Receiving Calls WWW.ERTEBATGROUP.COM 5.1 Making and Receiving Calls Making Calls To call another extension extension no. Off-hook. Dial extension number. Talk. To call an outside party outside phone no. Off-hook. Talk. Enter automatic Dial outside phone line access number. number. - Page 31 • ONP 2048 kbit/s digital structured leased lines (D2048S) Panasonic System Networks Co., Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.ptc.panasonic.eu...
- Page 32 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Copyright: This material is copyrighted by Panasonic System Networks Co., Ltd. , and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic System Networks Co., Ltd.