Table of Contents
Advertisement
Quick Links
TwinGig Overview
Installation Notes for the Cisco
TwinGig and OneX Converter Modules
PID: CVR-X2-SFP and CVR-X2-SFP10G
This note provides the installation instructions for the Cisco TwinGig and OneX
Converter Modules. This document contains these sections:
TwinGig Overview, page 1
•
OneX Overview, page 4
•
Converter Module Installation, page 7
•
Obtaining Documentation and Submitting a Service Request, page 16
•
The Cisco TwinGig Converter Module (model CVR-X2-SFP), also known as a
converter module, is a hot-swappable input/output (I/O) device that slides into a
10-Gigabit Ethernet X2 slot on a switch. It converts the 10-Gigabit X2 interface
into a dual SFP interface. It was developed for the Catalyst 3560-E switch but is
supported on other platforms. The converter module is shown in
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2007–2010 Cisco Systems, Inc. All rights reserved.
Figure
1.
Advertisement
Table of Contents
Related Manuals for Cisco TwinGig CVR-X2-SFP
Summary of Contents for Cisco TwinGig CVR-X2-SFP
- Page 1 Installation Notes for the Cisco TwinGig and OneX Converter Modules PID: CVR-X2-SFP and CVR-X2-SFP10G This note provides the installation instructions for the Cisco TwinGig and OneX Converter Modules. This document contains these sections: TwinGig Overview, page 1 • OneX Overview, page 4 •...
- Page 2 Table 1 lists the SFP modules that the converter module supports. Use only Cisco SFP modules in the converter module. Each Cisco module has an Note internal serial EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the module meets the requirements for the switch.
- Page 3 1310 62.5 6562 feet (2 km) 6562 feet (2 km) 1000BASE-SX 62.5 722 feet (220 m) 62.5 902 feet (275 m) 1640 feet (500 m) 1804 feet (550 m) Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04...
-
Page 4: Onex Overview
OneX Overview The Cisco OneX Converter Module (model CVR-X2-SFP10G),also known as a converter module, is a hot-swappable input/output (I/O) device that slides into a 10-Gigabit Ethernet X2 slot on a switch. It converts the 10-Gigabit X2 interface into a single 10-Gigabit SFP+ interface. - Page 5 Use only Cisco SFP+ modules in the converter module. Each Cisco module has Note an internal serial EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the module meets the requirements for the switch. Table 3...
- Page 6 Type (micron) (MHz/km) Cable Distance 10GBASE-SR 62.5 85 feet (26 m) 62.5 108 feet (33 m) 216 feet (66 m) 269 feet (82 m) 2000 984 feet (300 m) Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04...
-
Page 7: Converter Module Installation
Caution Proper ESD protection is required whenever you handle Cisco equipment. Installation and maintenance personnel should be properly grounded by means of grounding straps to eliminate the risk of ESD damage to the equipment. -
Page 8: Installation Guidelines
• install it in the slot. Installing the module at an angle can damage it. Any module that is only partially connected to the switch might not operate correctly. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... -
Page 9: Installing And Removing The Converter Module
To install a converter module in the switch module slot, follow these steps: Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface. Step 1 Remove the 10-Gigabit Ethernet module slot EMC plugs and save. Step 2 Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... - Page 10 Step 5 SFP or SFP+ Module” section on page 13). The switch detects the presence of both the converter module and any inserted Cisco SFP or SFP+ modules. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04...
-
Page 11: Removing A Converter Module
Place all SFP or SFP+ modules and converter modules in an antistatic bag or other Step 4 protective environment. Replace the EMI plug in the switch empty 10-Gigabit Ethernet module slot. Step 5 Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... -
Page 12: Installing And Removing Sfp Or Sfp+ Modules
SFP module. Disconnect all cables before removing or installing an SFP or SFP+ module. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... -
Page 13: Installing An Sfp Or Sfp+ Module
If the module has a bale-clasp latch, close it to lock the SFP or SFP+ module in Step 5 place. Remove the dust plugs from the SFP or SFP+ module and save. Attach the cables Step 6 to the SFP or SFP+ module. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... - Page 14 S E R IE S P o E - 4 8 Converter module Send (TX) optical bore SFP modules Receive (RX) optical bore 1. Lower SFP modules are inverted. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04...
-
Page 15: Removing An Sfp Or Sfp+ Module
Grasp the SFP or SFP+ module, and carefully remove it from the converter Step 5 module. Installation Notes for the Cisco TwinGig and OneX Converter Modules 78-17572-04... -
Page 16: Obtaining Documentation And Submitting A Service Request
The RSS feeds are a free service and Cisco currently supports RSS version 2.0. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.