1. Manuals
  2. Brands
  3. Velleman components Manuals
  4. Emergency Phone
  5. CTC710
  6. Operation manual

Velleman components CTC710 Operation Manual

Wireless voice dialler
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CTC710
Wireless Voice Dialler
Draadloze doorkiezer
Transmetteur téléphone sans fil
Operation manual
Handleiding
Manuel

Advertisement

Table of Contents
loading

Summary of Contents for Velleman components CTC710

  • Page 1 CTC710 Wireless Voice Dialler Draadloze doorkiezer Transmetteur téléphone sans fil Operation manual Handleiding Manuel...

  • Page 2: Table Of Contents

    Table of Contents 1. Introduction 1. What the Voice Dialler does 2. Model 2. Wireless Voice Dialler 1. Identifying the parts 2. About the power supply 3. How to mount the Voice Dialler 4. Preparing the Auto Dialler 5. Basic operation 6.

  • Page 3: Introduction

    1. Introduction 1. What the Voice Dialler does The Voice Dialler can store up to 6 telephone numbers and record and play back emergency messages. With a total message capacity of 20 seconds, the choice is yours whether you store 1, 2 or 3 different messages of variable length for different situations i.e.

  • Page 4: Wireless Voice Dialler

    2. Wireless Voice Dialler 1. Identifying the parts 1. RDY LED 3. NUMERIC KEYS 8. MICROPHONE 2. REC LED 4. SET KEY 5. TEST KEY 6. CE KEY 7. REC KEY 1. RDY LED (green LED) When idle, the LED will flash every 1 second. During setting in keypad operation, the LED will speed flash.
  • Page 5 3. NUMERIC KEYS These are used for keying in the emergency telephone numbers. You can also set the priority of the telephone numbers to determine which numbers are tried first in an emergency. When you wish to test the system, you also use these key for specifying which number you want to test.
  • Page 6 16. WALL MOUNT BRACKET 13. TERMINAL BLOCK 12. TONE/PULSE SELECTION JUMPER 10. SYSTEM ID CODE SWITCH BLOCK 14. PROTECTIVE COVER 9. PHONE JACK 11. DC 12V JACK 15. TABLE MOUNT BRACKET 12. TONE/PULSE SELECTION JUMPER This 2-pin jumper (JP2) is used to select whether traditional pulse dialling or tone dialling method is used.

  • Page 7: About The Power Supply

    17. PLUG-SOCKET CABLE The Tel line provided by Plug-Socket cable the tel company is plugged into this phone jack. The tel set is plugged Plug into the phone jack into this phone jack. of the Voice Dialler. 2. About the power supply An AC power adapter is required to connect to a wall outlet.

  • Page 8: How To Mount The Voice Dialler

    3. How to mount the Voice Dialler The Voice Dialler can be placed on top of a table or mounted on the wall. For table mounting, position the bracket as the picture shown below, then slowly lift the bracket upwards. 4.

  • Page 9: Basic Operation

    Note : If you are using this Voice Dialler with our alarm system having 256 ID code combinations, (that is when the system ID code switch block of the alarm system has only 2 positions, up being the ON position and down being the OFF position), please not the down position marked as "-"...
  • Page 10 C. When idle, the RDY LED is flashing slowly every 1 second. When you start the setting, the RDY LED will flash fast. This let you know the setting is in progress. D. If any time you want to abort the current keyings, just press "CE" and you can restore again.
  • Page 11 The identity code is a 3-digit number you can key in any number at your discretion. This enables the recipient to know the call is from the Voice Dialler. ^^Note : The procedure to store pager number may vary depending on the pager system used in a specified area.
  • Page 12 d. Store the telephone number in an EPABX telephone system. If you Voice Dialler is installed in an EPABX system, the EPABX access code "0" or "9" and * key must be keyed in after the priority number. Press SET Key in priority number (1-6) Press 0 or 9 (EPABX access code) Press *...
  • Page 13 If you record 2 messages, record the fire alarm and panic/emergency alarm message as message no. 1, the burglar alarm message as message no. 2. The procedure to record the message is : press REC, press 1 / 2 / 3 (as message no.

  • Page 14: How To Connect The Auxiliary Detectors

    6) Stop the dialling If any time you want to stop the dialling, just press CE. 7) Dialling test To check if the Voice Dialler can actually dial the number you have set and send the pre-recorded message, press TEST then key in the priority number (1-6) of the telephone number you wish to test.

  • Page 15: Important Notes

    If you have any smoke or gas detectors, connect them across pin 1 and pin 4. If you have any PIR, door switch or broken glass detectors, connect them across pin 2 and pin 4. If you have any panic/emergency button, connect them across pin 3 and pin 4.
  • Page 16 5) If no message or no telephone number is stored, the Voice Dialler will not dial. 6) If certain type of alarm occurred, but the corresponding message is not stored, the Voice Dialler will play message no. 1.

Table of Contents