Table of Contents
Advertisement
TK-2317
5. Self Programming Mode
Write mode for frequency data and signaling, etc. To be
used ONLY by the authorized service person maintaining the
user's equipment. After programming, reset the FPU to the
"Self- Programming" disabled mode. Transceivers CANNOT
be delivered to the end-user in the self-programming mode.
5-1. Enter to the Self Programming Mode
Press and hold the [S] key for 2 seconds while turning
the transceiver power on.
When the transceiver enters in the self programming
mode, "1- 1" is displayed 2 seconds after "SELF" is dis-
played.
Note:
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
5-2. Adding the Data Password
If the Data password is set to the transceiver, you must
enter the password to activate a self programming mode.
The maximum length of the password is 6 digits.
The following describes how to enter the password.
1. Press and hold the [S] key for 2 seconds while turning
the transceiver power on.
2. "SLF.LOCK.R" (When the Read authorization password is
set to the transceiver.) / "SLF.LOCK.W" (When the Over-
write password is set to the transceiver.) is displayed on
the LCD.
3. If the [selector] knob is rotated while "SLF.LOCK.R"/ "SLF.
LOCK.W" is displayed, the number (0 to 9) fl ashes on the
LCD.
When you press the [C>] key, the currently selected num-
ber is determined.
If you press the [A] key, the least digit of the password is
deleted.
If you press the [S] key after entering the password in this
procedure, "SELF" is displayed if the entered password is
correct.
If the password is incorrect, "SLF.LOCK.R"/ "SLF.LOCK.W"
is redisplayed.
5-3. Channel Selection Mode
In this mode, the Zone or Channel can be selected.
Press and hold the [S] key for 2 seconds while turning
the transceiver power on to enter self programming mode.
When the transceiver enters in the self programming mode,
the transceiver automatically enters the Channel Selection
mode.
2 seconds after displaying "SELF", "1- 1" appears on the
LCD.
The setup item for channel selection mode is as follows.
Setup item
Select
Zone/Channel
6
REALIGNMENT
Display
Remarks
*** - ***
Zone: 1~128
*** - ***
Channel: 1~128
Key operation
Key
Toggle between Zone selection and Channel selec-
[Selector]
tion
[Side1]
No action
[Side2]
No action
[S]
Enter the Item Setting mode
[A]
Return to the Channel Selection mode
Decrement the blinking Zone/Channel number by 1.
[<B]
Press and hold to decrement in steps of 10.
Increment the blinking Zone/Channel number by 1.
[C>]
Press and hold to decrement in steps of 10.
Note:
If a non-existing Zone-Channel is selected and the mem-
ory for all 128 channels is already fi lled, an error tone will
sound and "MEM.FULL" will appear on the LCD for 2 sec-
onds.
5-4. Item Selection Mode
In this mode, the following items can be selected.
•
RX frequency
•
RX signaling
•
TX frequency
•
TX signaling
•
RF power Hi/Low
•
Scan Del/Add
•
Beat shift on/off
•
Compander on/off
When the [S] key is pressed in the Channel Selection
mode, the transceiver enters the Item Selection mode.
Key operation
Key
[Selector]
The selected item changes
[Side1]
No action
[Side2]
No action
[S]
Enter the Item Setting mode
[A]
Return to the Channel Selection mode
[<B]
Error tone sounds
[C>]
Error tone sounds
Key Function
Key Function
Hide quick links:
Advertisement
Table of Contents
