Advertisement
Quick Links
1.
INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 13
2.
INSTALLATION OF THE STERILIZER _______________________ 15
3.
DESCRIPTION OF CONTROLS ____________________________ 17
4.
USE OF THE STERILIZER ________________________________ 19
5.
CLEANING AND MAINTENANCE ___________________________ 20
6.
EXTRAORDINARY MAINTENANCE _________________________ 22
IDENTIFICATION: HOT-AIR STERILIZER
MODEL: DRY STERIL 60V
YEAR OF CONSTRUCTION: .....................
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified technician who must install the appliance, set it functioning
and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.
12
Contents
Advertisement
Summary of Contents for Smeg DRY50V
-
Page 1: Table Of Contents
INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 13 INSTALLATION OF THE STERILIZER _______________________ 15 DESCRIPTION OF CONTROLS ____________________________ 17 USE OF THE STERILIZER ________________________________ 19 CLEANING AND MAINTENANCE ___________________________ 20 EXTRAORDINARY MAINTENANCE _________________________ 22 IDENTIFICATION: HOT-AIR STERILIZER MODEL: DRY STERIL 60V YEAR OF CONSTRUCTION: ... -
Page 2: Instructions For Safe And Proper Use
Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE STERILIZER. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE STERILIZER. - Page 3 ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE 0 (OFF) POSITION WHEN YOU FINISH USING THE STERILIZER. NEVER PUT INFLAMMABLE OBJECTS IN THE STERILIZER: THEY COULD BE ACCIDENTALLY LIGHTED AND CAUSE FIRES. THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS LOCATED IN AN EXPOSED POSITION AT THE REAR OF THE STERILIZER.
-
Page 4: Installation Of The Sterilizer
Instructions for the installer 2. INSTALLATION OF THE STERILIZER The sterilizer must be set up on a perfectly flat surface and left standing free. Make sure to allow enough room at the back for easy access to the terminal strip for connection of the power cable to mains. Installation must be carried out by a qualified technician in compliance with applicable regulations in force. - Page 5 Instructions for the installer 2.1.1 Safety thermostat The sterilizer is fitted with a safety device which trips in case of serious malfunction. To reset, contact the nearest servicing centre. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the sterilizer.
-
Page 6: Description Of Controls
Instructions for the user 3. DESCRIPTION OF CONTROLS THERMOSTAT KNOB This permits selection of the ideal cooking temperature. Turn the knob clockwise to the desired temperature. Adjustment is progressive so that the sterilizer also operates at any intermediate value. When the knob is turned to the symbol, the fan is swItched on but the heating element is not. - Page 7 When on, it indicates that the safety thermostat with automatic reset has been tripped by an appliance malfunction, cutting off the power supply. The oven cannot be reused until this light goes out. THERMOMETER Shows the temperature reached inside the oven.
-
Page 8: Use Of The Sterilizer
Instructions for the user 4. USE OF THE STERILIZER 4.1 Warnings and general advice When using for the first time, it is advisable to heat up the sterilizer to its maximum temperature for enough time to burn off any possible oily manufacturing residues. -
Page 9: Cleaning And Maintenance
Instructions for the user 5. CLEANING AND MAINTENANCE Important: never spray water directly on to the sterilizer. Never use pressure nozzles. Before any intervention, disconnect the power supply of the sterilizer. 5.1 Cleaning stainless steel parts To maintain stainless steel parts in perfect condition, clean regularly at the end of the work day. - Page 10 Instructions for the user Cleaning the inside of the sterilizer To maintain the sterilizer in perfect condition, clean it regularly at the end of the work day. Allow to cool first. Take off all removable parts. Remove the side guides by unscrewing the ring nut A and sliding them out of the rear hole B.
-
Page 11: Extraordinary Maintenance
Instructions for the user 6. EXTRAORDINARY MAINTENANCE The sterilizer may require extraordinary maintenance or replacement of parts subject to wear such as seals, bulbs, and so on. The following instructions describe how to carry out these minor maintenance operations. Before any intervention, disconnect the power supply of the sterilizer.