5.10.1. Menu to edit blocks ..................5.10.2. Selection of the block ................... 5.10.3. Definition of the performance mode ............. 5.10.4. Adding cells ....................5.10.5. Eliminating cells ................... 5.10.6. Edition of cells ....................5.10.7. Deletion of the cutting meter ................ C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Page 4
5.11.1. Block selection ..................... 5.11.2. Operating with one block ................6. ADJUSTMENT OF THE BLADES ................... 7. STANDBY OF THE MACHINE ....................8. UNUSUAL PERFORMANCE SITUATIONS ................9. WARNINGS ..........................10. ACCESORIES ........................TECHNICAL ANNEXES C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
The C3006 is according to the European regulations and normative for the manufacturing of machinery. PRADA NARGESA S. L is not liable for any damage that might occur due to misuse or failure by users to comply with the safety standards.
1.4. Identification of the machine Rammers Commands control Electric box Front protection Screws to level the machien Lifting spots Stands for the Side protections entrance of the metal sheet Photocell C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
4 mm (700N/mm Nº of hammers 15 units Cutting length 3030 mm Neck 173 mm Gauge displacement 700 mm Strokes per minute 12 strokes Position accuracy and repeatibility +/- 0,1 mm Dimensions 3750x2000x1850 mm Weight 8000 Kg C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
1.6. Description of safety devices The fixed safety devices the guillotine C3006 has are lateral to avoid any handling, the front protection avoids from acceding to the rammers side, Protections in the back side of the machine covering the belts and pulley of the back top, the outet ramp for the material and the upper protection cover of the piston mo- veable part.
* Temperature from -25 to 55ºC or 75ºC for a length of time not exceeding 24h (these must be considered storage conditions) * It is advisable not to pile up machines or heavy objects on top of it C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
- If it is a steady and daily use, they must be greased avery month. - Lubricate the top spindles weekly with grease or oil. - Lubricate all guides greasers every month. Oil dipstick Fill plug Drain plug C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
It is advisable to work under the following atmospheric conditions: - Room temperature between +5 °C and +40 ºC without exceeding an average temperature of +35 °C within 24 hrs - Humidity between 30% and 90% without water condensation C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
4.4 Connection to power supply The guillotine C3006 is equipped with two three-phased enngines 230 / 400 V: one of them is for the top (0,37KW),which must be always connected triangularly and another one (9,2 kW) connected star like to be connected to a 400v + neutral supply.
5.1. Introduction This manual is designed for the user of the Guillotine C3006, since it has got important information about the use of it and the peculiar features of the machine. Therefore it is advisable to follow step by step the points detailed in this book so a good understanding of its performance could be achieved.
NARGESA C3006 Picture 9. C3006 initialization label At the same time it will be seen intermitently in the 7-fragments displays the total length of the top while this is moved at a moderate speed, getting apart from the shears blade in order to be located in the highest working figure.en la cota Once this top is located in the indicated positions, then the intermitence of the 7-...
To go through the different memories, it is necessary to press the Navigation keys, silkscreen printed with: To the pressure of each of these keys there will appear on screen the information according to the current memory of the top. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Picture 14. Information of thetop of the memory 0 At pressing the first number ( 5 in our sample), the message on the screen changes into this other one: M00 CONT: 0000 “”””””””” 5.0 mm Picture 15. Inserting a new figure C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Page 17
Then unless the new inserted figures is not higher than the total length of the top, it could be seen on the LCD displays the information reflected in the following picture: POSITIONING TOP = 443.2 mm Picture 20. Inserting a new figure C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
When we do that the memory of the current top shows up on screen again, with the value thet it had before the modification we were going to make. M00 CONT: 0000 TOP = 10.0 mm Picture 24. Information of the memory of the top 0 C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
If on the other hand your intention is to operate in Manual mode, the only thing to do is to press the Manual key. In this case, unlike the previous one, the blade will not move. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
So the operative will make a reasonable use of it, since the more times he presses the pedal to make the same number of cuts of sheet, the more expensive the rental will be. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
TOP = 56 mm Picture 37. Information of the top memory 2 after cancelling the meter deletion Therefore, each time you want to delete the meterof the current memory, just follow the steps described in this section. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
In case the current figure is different from 100.0mm, it is necessary to insert the figure you have inserted and press th e Return Key to confirm the correction. When you do that the machine will re-start following the process described in section 5.3. Feeding of the Guillotine C3006 C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
5.10. Menus of the block Apart from the so mentioned 10 memories of the top, the Guillotine C3006 has 50 blocks of memory. Each of them may have a maximum of 10 cells and at the same time each of these cells may store a cutting figure for the top.
5.10.1. Menu to edit blocks This menu is useful for editing the different blocks the Guillotine C3006 has, that is to say, it allows you to create cells and introduce the different positions of the top to make a whole sequence of sucessive cuts, as well as defining the perfomance mode of these, Manual or Automatic.
As it has said in the previous section, the 50 existent blocks have been preset for its performance in automatic mode, because it more usual to work with memory groups. Nevertheless, you can change this performance mode for the Manual one. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Once the message has dissapeared, the lower row of the display will show the current cell again. BLOCK 02 0000 AU Max. Nº of Cells Picture 48. Attempt to insert more than 10 cells per block C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Picture 50. Edition of the memory block 2 When pressing the first number (5 in this case), the message on screen changes into this other one. BLOCK 02 0000 AU ......5 mm Picture 51. Inserting a new figure C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Page 29
Any time you want to cancel the operation while you are inserting a new figure, just press the ESC key. Then you will see the block again on the screen , as well as the cell you were before deciding to insert a new figure. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
0. BLOCK 02 0000 AU CELL 0 = 100.0 mm Picture 59. Information of the memory block 2 with the meter already deleted. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
In case this selected block hasn’t got defined cells in the LCD display will appear one error message during 1 sec indicating that the block is empty. ATTENTION EMPTY BLOCK Picture 62. Attempt to with a block without defined cells C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
5.11.2. Operating with one block When working with a given block, the Guillotine C3006 gets the top in the position according to the value in the first cell of this block. During this process the positioning message will show up on the LCD screen.
Moreover, when the big cutting part is in its correct position, it automatically will go back to the preset top memory in which it will be before acceding to the menu for adjusting the blades. C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
7. STANDBY OF THE MACHINE The StandBy mode is basically when the C3006 keeps the supply but it is inactive. That is to say, it is like “asleep”. Besides, here the 7 fragments displays are deactivated and you could see a message like the one...
Error in the Encoder reading. So in case of having any of the previously described situations, the Guillotine C3006 goes to such a state that it aborts any operations that’s being carried out at the moment, deactivating the 7fragments displays and wing up a message on the screen indicating the unusual situation that has happened.
- Do not cancel any protection device provided by the machine. - NARGESA SL will not accept any responsibility if an accident occurs due to a negligent use of the machine on the operative’s side or for not bearing in mind the usage and safety rules decribed in this manual.
The blades are treated by various processes, which reinforces its liability and resistance at a normal use condition. The guillotine C3006 has and upper blade and a lower blade each of them has got four exchangeable cutting corners. The adjustment between the two blades should be 0.04 mm.
Page 38
Technical annex Hydraulic shear C3006 List of parts Electric maps Hydraulic map C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Page 39
A1. List of parts C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK...
Page 47
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 10...
Page 48
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 11...
Page 49
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 12...
Page 50
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 13...
Page 51
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 14...
Page 52
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 15...
Page 53
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 16...
Page 54
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 17...
Page 55
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 18...
Page 56
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 19...
Page 57
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 20...
Page 58
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 21...
Page 59
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 22...
Page 60
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 23...
Page 61
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 24...
Page 62
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 25...
Page 63
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 26...
Page 64
A2. Electric maps C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 27...
Page 65
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 28...
Page 66
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 29...
Page 67
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 30...
Page 68
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 31...
Page 69
C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 32...
Page 70
A3. Hydraulic map C3006 HYDRAULIC SHEAR INSTRUCTIONS BOOK A 33...
Page 71
3. Complete the form with your details and press Send 4. The window Message Sent confirms your data has been successfully sent to Prada Nargesa SL. Your machine has been registered and has a warranty of three years in total.