Advertisement
English-3
RJA529152-039
Getting Ready
n
Location Precautions
●
Use an electrical outlet near the Signage Unit. Always use the
Signage unit so that the power cord can be easily unplugged.
●
Be sure to keep all surrounding objects at least 30cm (11.8
inches) from the Signage Unit. Particular care is required to
keep objects away from the intake and exhaust vents on either
side of the Signage Unit.
●
Airflow from air conditioning equipment redirecting heat being
exhausted from the area around the Signage Unit lens can
cause heat ripples to appear in the projected image. If this
happens, adjust the airflow of the air conditioning equipment
or move the Signage Unit.
●
Do not use or store the Signage Unit in any one of the
locations described below.
–
On or near any device that generates heat (household
appliances, computers, etc.)
–
On any surface that is not firm and stable (on top of soft
material, etc.)
n
To use the Signage Unit on a network
Visit the CASIO website for information about using the Signage
Unit on a network.
n
Ad Sticker
The illustration below shows the location on the Signage Unit
where you can affix a sticker* for an ad, etc.
*
The Signage Unit does not come with stickers. For more
information, visit the CASIO website.
Ad sticker
n
To prepare the Signage Unit for first use
12
Install the provided nickel metal hydride
(Ni-MH) battery into the Signage Unit.
(1) Stand the Signage Unit up on its side.
(2) Loosen the two battery cover screws on the bottom of
the Signage Unit and then remove the cover.
D
MG-30MBPACK_e.indd
3
Connector
Screws
Slots
Battery cover
(3) Remove the protective paper from the adhesive surface
inside the battery cover.
(4) Orienting the cable of the Ni-MH battery so it can exit
through the slot provided on the battery cover, affix the
side of the battery to the adhesive surface inside the
battery cover.
•
Press down firmly on the battery to ensure that it is
secured on the adhesive surface.
Battery cover (inside surface)
Slot
Plug
Cable
Adhesive
surface
Hooks
Ni-MH battery
(5) Insert the Ni-MH battery's plug into the Signage Unit's
connector.
(6) Insert the two hooks of the battery cover into the cover
slots, attach the battery cover, and then tighten the two
screws to secure it in place.
22
Lay the Signage Unit back down in its normal
position, and place it on a firm level surface
for use.
•
See "Location Precautions" for information about suitable
locations.
32
Attach the screen to the Signage Unit.
Screws
Included hex wrench
(1) Use the included hex wrench to remove the center
screw from the screen support.
•
You do not need to remove the two screws on either
side of the screen support.
(2) With the gray surface of the screen facing forward,
insert it into the screen support as shown in the
illustration.
•
Grasp both sides of the screen as you insert it. Take
care not to press down on the screen with excessive
force, etc.
(3) Use the hex wrench to tighten the three screen support
screws and secure the screen in place.
Important!
Do not turn on the Signage Unit without the screen attached.
Doing so creates the risk of strong light from the Signage Unit
shining directly into eyes.
42
If the Signage Unit does not have an SD card
loaded, load a card into the card slot.
•
For more information, see "To load an SD card".
52
Use a LAN cable to connect the Signage Unit
to a network.
62
Use the supplied AC adapter to connect the
Signage Unit to an AC outlet.
•
This will automatically turn on the Signage Unit and
display the startup screen on the touch panel.
•
If the Signage Unit's time and date settings have already
been configured, advance to step 8.
•
If time and date settings need to be configured, display
the date setting screen on the touch panel. Advance to
step 7.
72
Use the touch panel to configure date and
time settings.
(1) On the date setting screen, specify the current year,
month, and day, and then tap [Set].
(2) On the time setting screen that appears, specify the
current hour and minute and then tap [Set].
82
Wait until the "Play Mode" screen appears on
the touch panel.
•
Content will automatically start playing after the "Play
Mode" screen appears.
•
For information about supported button operations during
content play, see the "CASIO Signage User's Guide".
92
After you are finished using the Signage Unit,
perform the steps below to turn it off.
(1) Hold down the power button until a menu like the one
shown below appears on the touch panel.
Power off
Navigate home
(2) On the menu, tap [Power off].
(3) On the confirmation dialog box that appears, tap [OK].
Note
It may take some time for auto play of content starts after the
Signage Unit is turned on. How much time it takes depends on
the network where the Signage Unit is connected, the current
Signage Unit setup, the volume of new data (when updated data
is downloaded automatically over the network), and other factors.
n
To load an SD card
12
Turn off the Signage Unit and unplug its AC
adapter from the power outlet.
22
Find the small cover on the front of the
Signage Unit, and press at the point indicated
by the arrow, below.
2014/08/25
15:09:25
Advertisement
