Page 1
Self Diagnosis Supported model SERVICE MANUAL BG-3S CHASSIS MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO. KV-PF21M70 RM-952 Hong Kong SCC-U17H-A KV-TF21M61 RM-952 Singapore SCC-U29A-A KV-TF21M90 RM-952 Hong Kong SCC-U17G-A KV-TF21P11 RM-952 SCC-U24C-A (KV-PF21M70) (KV-TF21M61) (KV-TF21M90) (KV-TF21P11) TRINITRON COLOR TV ®...
Page 2
CARBON PAINTED ON THE CRT, AFTER REMOVING THE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE ANODE. COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL.
Replacement of Bar Control......2-6. Terminal Bracket Removal ........33 6. EXPLODED VIEWS 2-7. Degauss Coil Removal ..........34 6-1. Chassis (KV-PF21M70) ........... 93 2-8. Picture Tube Removal ..........34 Chassis (KV-TF21M61/TF21M90/TF21P11)..95 3. SET-UP ADJUSTMENTS 7. ELECTRICAL PARTS LIST ........97 3-1.
Page 4
• IC1800 is shorted. (C5 board shorted. (OVP) 004:001~255 (except PF21M70)/ • Has entered standby state • Vertical deflection at the same time (C3 Board (KV-PF21M70)). after horizontal raster. stopped • -13V is not supplied. • Vertical deflection pulse is • Horizontal (A board) stopped.
Page 5
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT 2 times 5 times Lamp ON 0.3 sec. Lamp OFF 3 sec. Lamp OFF 0.3 sec. STANDBY/SLEEP lamp Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic.
Page 6
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [Screen display] / channel [5] / Sound volume [-] / Power ON...
Page 7
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 SELF-DIAGNOSTIC CIRCUIT IC301 IC001 IC003 Y/CHROMA JUNGLE SYSTEM MEMORY FROM IK-IN IO-8DAT B-DAT FROM O-LED [+B] Q604 C5/C3 PROTECT IO-SDAT [V] Q509/507 [+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven...
Page 8
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of GENERAL the Operating Instruction Manual remain as in the manual. (KV-PF21M70) Using Your New TV WARNING • Dangerously high voltages are present inside the TV.
Page 9
Connecting optional components Notes • If you connect a stereo VCR, connect the yellow plug to (the yellow jack) and the white plug to (the black jack). You can connect optional video components, such as a VCR, multi disc player, •...
Page 10
Securing the TV Presetting channels To prevent the TV from falling, secure the TV using one of the following methods: You can preset up to 100 TV channels in numerical sequence from program With the supplied screws, attach the band to the TV stand and to the rear of Number buttons number 1 using the remote and the the TV using the provided hole.
Page 11
Presetting channels (continued) Presetting channels manually To change the TV system setting Press SELECT until SELECT If the picture or sound is abnormal when receiving programs through the ˘ (antenna) “MANUAL PROGRAM” terminal appears. MANUAL PROGRAM (1) Press SELECT until “TV SYS” appears. TV SYS: B/G Press + or –.
Page 12
Watching the TV Watching the TV (continued) ¤ Additional tasks … This section explains functions used while watching the TV. Most operations Do this can be done using the remote. Turn off temporarily Press u. The u indicator on the TV lights up red. Number buttons Press U on the TV.
Page 13
Advanced Operations Customizing the Setting the Wake Up timer SOUND Á PROGR MODE picture and sound SOUND MODE Press until the WAKE UP TIMER:10M desired period of time After 10 minutes SELECT appears. You can customize the picture and + or – sound by selecting the picture and PIC MODE sound modes or by adjusting its...
Page 14
Blocking the Adjusting the picture and sound settings channels Press SELECT until the SELECT (CHILD LOCK) desired setting appears. PICTURE You can prevent a child from watching Each time you press PICTURE COLOR BRIGHT certain programs by using the buttons ÷...
TV system (TV SYS). Press U (main power) to turn off your TV. (page 10) Inform your nearest Sony service center about the number of times the No picture • Check the power cord, antenna and the • The power cord, antenna u indicator flashes.
Page 16
(page 10) external sources, e.g., TV screen. heavy machineries, nearby broadcast station. No sound • Contact your nearest Sony service indicator on your • Your TV may need service. center. (page 17) TV flashes red a number of times between 3-second intervals.
Page 17
Identifying parts and controls (continued) Identifying parts and controls Remote Control Refer to the pages indicated in parentheses ( ) for details. Front panel !º !¶ !¡ ÷ ÷ JUMP JUMP !™ !§ SOUND SOUND Á PROGR Á PROGR MODE MODE !£...
SECTION 1-2 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of GENERAL the Operating Instruction Manual remain as in the manual. (KV-TF21M61/TF21M90) Using Your New TV WARNING • Dangerously high voltages are present inside the TV. Getting Started •...
Page 19
Connecting optional components Notes • If you connect a monaural VCR, connect the yellow plug to (the yellow jack) and the black plug to -L (MONO) (the white jack). You can connect optional audio/video components, such as a VCR, multi disc player, •...
Page 20
Securing the TV Presetting channels To prevent the TV from falling, secure the TV using one of the following methods: You can preset up to 100 TV channels in numerical sequence from program With the supplied screws, attach the band to the TV stand and to the rear of Number buttons number 1 using the remote and the the TV using the provided hole.
Page 21
Presetting channels (continued) Presetting channels manually To change the color system setting Press SELECT until SELECT If the color is abnormal when receiving programs through the ˘ (antenna) terminal “MANUAL PROGRAM” or the … (video input) jack appears. MANUAL PROGRAM (1) Press SELECT until “COL SYS”...
Page 22
Watching the TV Watching the TV (continued) ¤ Additional tasks … This section explains functions used while watching the TV. Most operations Do this can be done using the remote. Turn off temporarily Press u. The u indicator on the TV lights up red. Number buttons Press U on the TV.
Page 23
Advanced Operations Customizing the Setting the Wake Up timer SOUND Á PROGR MODE picture and sound SOUND MODE Press until the WAKE UP TIMER:10M desired period of time After 10 minutes appears. SELECT You can customize the picture and + or – sound by selecting the picture and PIC MODE sound modes or by adjusting its...
Page 24
Blocking the Adjusting the picture and sound settings channels Press SELECT until the SELECT (CHILD LOCK) desired setting appears. PICTURE You can prevent a child from watching Each time you press certain programs by using the buttons PICTURE COLOR BRIGHT HUE* ÷...
Page 25
Selecting a stereo Selecting a stereo or bilingual program (continued) SOUND Á PROGR MODE or bilingual When receiving an A2 (German) program program Broadcasting On-screen display (Selected sound) A2 (German) stereo MONO STEREO You can enjoy stereo sound or bilingual FAVORITE (Regular sound) (Stereo sound)
Page 26
Viewing Teletext (continued) Viewing Teletext (KV-TF21M61 only) Additional Teletext tasks … TV stations broadcast an information Do this service called Teletext via some TV Press display a Teletext page on the TV channels. Teletext allows you to receive picture Each time you press , the screen changes as various information, such as shares follows: Teletext n Teletext and TV n TV.
Page 27
Count the number of times the u indicator flashes. Press U (main power) to turn off your TV. Inform your nearest Sony service center about the number of times the u indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.
Page 28
Troubleshooting Shortcuts For better viewing, please check the following connections. Antenna connection AC Connection Check the antenna direction. Check connection on Incorrect antenna direction may cause: the AC socket. • Snowy • Distorted • Noisy/ • Double image • Missing picture picture distorted...
Page 29
• The volume level is too low. If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer . • Press ¤ to cancel the muting. • The sound is muted.
Page 30
TV screen. heavy machineries, nearby (main power) button (5) broadcast station. 2 PROGR +/– (program) buttons (11) • Contact your nearest Sony service indicator on your • Your TV may need service. ¸ +/– (volume) buttons (11) center. (page 21)
Page 31
Identifying parts and controls (continued) Remote Control !º !¶ !¡ ÷ ÷ JUMP JUMP !™ !§ SOUND Á PROGR SOUND Á PROGR MODE MODE !£ SELECT SELECT !¢ PIC MODE PIC MODE FAVORITE FAVORITE !∞ 1 u (power) button (11) !§...
Page 32
SECTION 1-3 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of GENERAL- the Operating Instruction Manual remain as in the manual. (KV-TF21P11) Using Your New TV WARNING • Dangerously high voltages are present inside the TV. Getting Started •...
Page 33
Connecting optional components Notes • If you connect a stereo VCR, connect the yellow plug to (the yellow jack) and the white plug to (the black jack). You can connect optional video components, such as a VCR, multi disc player, •...
Page 34
Securing the TV Presetting channels To prevent the TV from falling, secure the TV using one of the following methods: You can preset up to 100 TV channels in numerical sequence from program With the supplied screws, attach the band to the TV stand and to the rear of Number buttons number 1 using the remote and the the TV using the provided hole.
Page 35
Presetting channels (continued) Presetting channels manually Skipping program numbers Press SELECT until SELECT “MANUAL PROGRAM” Press PROGR +/– or the number buttons until the unused or unwanted appears. program number appears. MANUAL PROGRAM Press SELECT until “MANUAL PROGRAM” appears. Press + or –. Press + or –.
Page 36
Watching the TV Watching the TV (continued) ¤ Additional tasks … This section explains functions used while watching the TV. Most operations Do this can be done using the remote. Turn off temporarily Press u. The u indicator on the TV lights up red. Number buttons Press U on the TV.
Page 37
Advanced Operations Customizing the Setting the Wake Up timer SOUND Á PROGR MODE picture and sound SOUND MODE Press until the WAKE UP TIMER:10M desired period of time After 10 minutes SELECT appears. You can customize the picture and + or – sound by selecting the picture and PIC MODE sound modes or by adjusting its...
Page 38
Blocking the Adjusting the picture and sound settings channels Press SELECT until the SELECT (CHILD LOCK) desired setting appears. PICTURE You can prevent a child from watching Each time you press certain programs by using the buttons PICTURE COLOR BRIGHT ÷...
Page 39
Viewing Teletext Viewing Teletext (continued) Additional Teletext tasks TV stations broadcast an information … service called Teletext via some TV Do this channels. Teletext allows you to receive various information, such as shares display a Teletext page on the TV Press picture market or news.
Page 40
Count the number of times the u indicator flashes. Noisy sound Press U (main power) to turn off your TV. Inform your nearest Sony service center about the number of times the No picture • Check the power cord, antenna and the •...
Page 41
• The color level setting is color on the screen, then press + or – to adjust too low. • Contact your nearest Sony service indicator on your • Your TV may need service. the color level. (page 15) center. (page 19)
Page 42
Identifying parts and controls (continued) Identifying parts and controls Remote Control Refer to the pages indicated in parentheses ( ) for details. Front panel !º !¶ !¡ ÷ ÷ JUMP JUMP !§ !™ SOUND Á PROGR SOUND Á PROGR MODE MODE !£...
2-3. F BRACKET REMOVAL (KV-TF21M61/TF21M90) Rear cover 2 F board 1 Three connectors Six screws (BVTP 4×16) Lever 2 Two screws (BVTP 4×16) (KV-PF21M70/TF21P11) 2-2. CHASSIS ASSY REMOVAL 2 F board 1 Three connectors Lever Lever Lever 1 Chassis assy More user manuals on...
2-5. REPLACEMENT OF PARTS 2-6. TERMINAL BRACKET REMOVAL For replacement of the Multi Button and Bar Optical ,unscrew to exchange with the new parts, and fix them with screws (+BVTP) respectively. (KV-PF21M70/TF21P11) (KV-TF21M61/TF21M90) 2-5-1. REPLACEMENT OF MULTI BUTTON Terminal board bracket...
NOTE : The picture tube for OCE model is upside down, and the positon for the anode cap and tension springs are changed accordingly. 3 F board 4 C5 board (except KV-PF21M70) C3 board (KV-PF21M70) 1 Demagnetization coil 5 Deflection yoke...
Page 46
•REMOVAL OF ANODE-CAP NOTE : After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT. •REMOVING PROCEDURES 1 Turn up one side of the rubber cap in the direction indicated by the arrow a. 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
KV-PF21M70/TF21M61/TF21M90/TF21P11 SECTION 3 RM-952 SET-UP ADJUSTMENTS • The following adjustments should be made when a complete Perform the adjustments in the following order : realignment is required or a new picture tube is installed. 1. Beam Landing • These adjustments should be performed with rated power 2.
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size V. STAT and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and Vertical Static Convergence Center dot H. STAT VR H.
Page 49
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 (2) Dynamic Convergence Adjustment Preparation: • Before starting this adjustment, adjust the horizontal static convergence and the vertical static convergence on DY (3) Screen-corner Convergence Fix a Permalloy assy corresponding to the misconverged areas a-d : screen-corner misconvergence a to d : Permalloy assembly –...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 3-3. FOCUS ADJUSTMENT 3-4. G2 (SCREEN) AND WHITE BALANCE Adjust FOCUS control on the flyback transformer for the best ADJUSTMENTS 1. G2 (SCREEN) ADJUSTMENT focus. 1) Set the PICTURE to normal. 2) Put to VIDEO input mode without signals.
KV-PF21M70/TF21M61/TF21M90/TF21P11 SECTION 4 RM-952 CIRCUIT ADJUSTMENTS 4-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-952 that comes with 1, 4 this unit. Select the adjustment item. ↓ a. ENTERING SERVICE MODE 3, 6 Raise/lower the data value. With the unit on standby ↓...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 4-2. ADJUSTMENT METHOD Item Number 00 of device GEO Use the same method for all Items. Use 1 and 4 to select the This explanation uses H-Position as an example. 1. Select “GEO 00 HPS” with the 1 and 4 buttons.
Page 53
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) H Position 50/60HZ 12 (7-2) CXA2130S(88H) 82 (7-2) H Size 50/60HZ 11 (7-2) 81 (7-2) Pin Amp 50/60HZ 13 (7-2) 83 (7-2)
Page 54
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) H Drive Pulse Width Switch 00 (6) 4F (6) AFC Gain Control TV/Video/Text 0F (1-0) 8D (1-0) H Oscillation 0C (7-4) 5B (7-4)
Page 55
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) Teletext Horizontal Position (58H) 18D (1-0) Teletext Vertical Position 18D (6-4) OSD H Position Option-Misc AC (7-2) Comb Selection A5 (7-6) APC Switch...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 4-3. PICTURE QUALITY ADJUSTMENTS BELL FILTER ADJUSTMENT SUB COLOR ADJUSTMENT 1. Input SECAM color-bar signal. 2. Connect the dual-trace oscilloscope to the pin 9 (R-Y) of 1. Input a PAL color-bar. CN303 (not mounted). 2. Set to the following condition: 3.
MAIN. TUVIF AUDIO TV V in TU101 TV L in BTF-WG441(I) PROSESSOR TV R in (KV-TF21M61/TF21M90) IC203 BTF-LG433(I) TDA7429S (KV-PF21M70 ) <slave: 80H> SP ASSY AUDIO OUT <slave: C0H> IC201 BTF-LG411 (KV-TF21P11) TA8248K (KV-TF21M61/TF21M90 only) CRT SOCKET R out R out...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in µF unless otherwise noted. • All electrolytic capacitors are rated at 50V unless otherwise noted. • All resistors are in ohms. kΩ = 1000Ω, MΩ = 1000kΩ...
Replace only with part number part are indicated with a collation number specified. in the remark column. 6-1. CHASSIS (KV-PF21M70) [: BVTP 3 × 12 7-685-648-79 REF. NO. PART NO. DESCRIPTION REMARK L: BVTP 4 × 16 7-685-663-71...
KV-PF21M70/TF21M61/TF21M90/TF21P11 KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 RM-952 6-2. CHASSIS (KV-TF21M61/TF21M90/TF21P11) [: BVTP 3 × 12 7-685-648-79 L: BVTP 4 × 16 7-685-663-71 NOTE : The picture tube for OCE model is upside down, and the REF. NO. PART NO. DESCRIPTION REMARK position anode cap and tension springs are changed accordingly.
When indicating parts by reference • MMH : mH, UH : µH number, please include the board name. noted. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK * A-1298-955-A A BOARD,COMPLETE (KV-PF21M70) C107 1-163-005-11 CERAMIC CHIP 470PF ******************** C108 1-126-933-11 ELECT 100MF...
Page 66
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C259 1-126-933-11 ELECT 100MF C528 1-162-134-11 CERAMIC...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C630 1-123-024-21 ELECT 33MF 160V D311 8-719-988-61...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK D901 8-719-069-60 DIODE UDZS-TE17-9.1B JR009 1-216-295-91 SHORT...
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <IC LINK> R013 1-216-065-91 RES,CHIP 4.7K 1/10W...
Page 70
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R221 1-216-295-91 SHORT R367 1-216-073-00 RES,CHIP 1/10W...
Page 71
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R562 1-249-401-11 CARBON 1/4W R644 1-249-419-11 CARBON 1.5K...
Page 72
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (KV-PF21M70) (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <TUNER> C051 1-163-251-11 CERAMIC CHIP...
Page 73
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C248 1-163-010-11 CERAMIC CHIP 0.0012MF C409...
Page 74
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C605 ! 1-127-942-51 CERAMIC 330PF 250V <CONNECTOR>...
Page 75
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK D521 8-719-302-43 DIODE EL1Z FB611 1-410-397-21 FERRITE 1.1UH...
Page 76
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK JR404 1-216-295-91 SHORT Q207 8-729-421-19 TRANSISTOR UN2213...
Page 77
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R027 1-216-073-00 RES,CHIP 1/10W R225 1-216-033-00...
Page 78
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R364 1-216-295-91 SHORT R536 1-216-067-00 RES,CHIP 5.6K...
Page 79
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R619 1-260-128-11 CARBON 270K 1/2W <RELAY>...
Page 80
! are critical for safety. Replace only with part number specified. 3 (KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * A-1331-884-A C3 BOARD, MOUNTED (KV-PF21M70) <TRANSISTOR> ********************* Q704 8-729-326-11 TRANSISTOR 2SC2611 7-682-948-01 SCREW +PSW 3X8 Q705...
Page 81
! are critical for safety. Replace only with part number specified. 5 (Except KV-PF21M70) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * A-1331-941-A C5 BOARD, MOUNTED (EXCEPT KV-PF21M70) <IC> ********************* IC1800 8-759-822-38 IC LA6510 7-682-948-01 SCREW +PSW 3X8 <JACK>...
Page 82
KV-PF21M70/TF21M61/TF21M90/TF21P11 RM-952 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. KV-TF21M61/ 5 (Except KV-PF21M70) TF21P11 only REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R739 1-247-807-31...
Page 83
1/10W 1-452-728-61 COIL, NA ROTATION (RT-154) R829 1-216-025-91 RES,CHIP 1/10W (KV-TF21M61/TF21M90 ONLY) R830 1-216-295-91 SHORT 1-501-372-81 ANTENNA, TELESCOPIC (KV-PF21M70 ONLY) R831 1-216-295-91 SHORT 1-505-740-11 SPEAKER (5X9CM) ! 1-574-062-11 R832 1-216-659-11 METAL CHIP 2.2K 0.50% 1/10W CORD, POWER (WITH CONNECTOR) 2.5A/250V...