Honeywell HD274HD2 Quick Installation Manual

Performance Series HQA HD274HD2 1080p
Indoor/Outdoor IR Mini Dome Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series HQA HD274HD2 camera.
Follow the instructions in this guide to install and set up your camera.

Cautions and Warnings

CAUTION
This device is configured for 12 V DC/24 V AC operation.
Do not connect to a higher voltage. Use only with NRTL-approved Class 2
power supplies.
CAUTION
IR emitted from this product. Do not view directly with
optical instruments. Do not stare directly into the lamp at a distance of less
than 3.3 ft (1 m).
CAUTION
Class 1 LED product. Invisible LED radiation (850 nm).
Avoid exposure to beam.

Important Safeguards

• Read and keep these instructions.
• Do not aim the camera toward a bright light source for extended periods to prevent
damage to the imager. Avoid operating the unit under or close to unstable light
sources or close to fluorescent lamps or objects reflecting light.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, or environments
where the operating temperature is outside the recommended range of –22°F to
140°F (–30°C to 60°C).
Dimensions
4.80 (122 mm)

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts
are missing or damaged, contact your dealer immediately.
• Camera
Document 800-22070 — Rev B — 05/2016 • Quick Installation Guide
• Mounting template sticker
• Allen key (L-wrench)
Tools needed (not supplied):
• Cordless drill
1

Preparing the Mounting Surface

1. Inspect the site where you want to install the camera. The mounting surface must be
flat and capable of supporting at least three times the weight of the camera.
2. Remove the backing from the mounting template sticker and affix the sticker to the
mounting surface.
Note
3. Drill three screw holes at the locations indicated on the mounting template sticker
and insert the three supplied plastic anchors in the holes.
4. If you are flush mounting the camera and want to store the cables inside the wall or
ceiling, drill a hole at the cable exit position on the mounting template and then pull
the power and video cables through the hole.
• Self-tapping screws (4)
• Plastic anchors (4)
• Power connector
• Phillips screwdriver
If you are using the side exit for the cable, note the orientation of the cable
exit notch. In outdoor installations the notch should point downwards to
prevent water from entering the camera housing.
Mounting surface
Plastic anchor
Self-tapping screw
Camera assembly
Dome cover
Security screw
HD274HD2 Camera Quick Installation Guide
2

Mounting the Camera

1. Using the supplied Allen key, remove the dome cover from the camera assembly
and set it aside.
2. Connect the power and video cables.
a. Connect the power connector of the camera to a 12 V DC/24 V AC power source.
b. Make one of the following video cable connections:
• Connect the black BNC connector of the camera to a coaxial video cable
to get an HD (HQA) signal.
• Connect the yellow BNC connector of the camera to a coaxial video cable
to get an SD (CVBS) signal.
• Connect both black and yellow BNC connectors to two coaxial video
cables to get both HD and SD signals.
Note When WDR is enabled, only the HD signal will be available.
BNC (Black, HQA)
Power
(12 V DC/24 V AC)
BNC (Yellow, CVBS)
3. Attach the camera assembly to the mounting surface using the supplied screws.
3
Aiming the Camera and Adjusting Zoom and Focus
1. Aim the camera lens in the desired direction.
2. Set the lens zoom and focus.
a. Connect the camera to a Honeywell Performance Series HQA DVR.
b. Log on to the DVR as the admin user. The default user name is admin
(case-sensitive) and the default password is 1234.
Document 800-22070 – Rev B – 05/2016