Antenna + VCR/Satellite receiver + HDD & DVD Recorder + TV
Before making or changing any rear panel connections, make sure that
all components are switched off and unplugged from the wall outlet.
Connect the cable from the antenna/cable TV outlet to HDD &
DVD Recorder.
Connect the AV1 connector on HDD & DVD Recorder to the
SCART AV connector on TV using a SCART cable. Also use
the Video/Audio Cable to connect AUDIO OUT(R/L)/VIDEO
OUT jacks on the HDD & DVD Recorder to the Audio & Video
jacks on the TV.
•
For the best picture quality, if your TV has Component video
jacks, you can use component cables instead of the yellow
video connector on the Video/Audio cable. If your TV has a
HDMI or DVI jack, you can use the HDMI or HDMI-DVI cable
instead of the yellow video connector on the Video/Audio cable.
Connect the AV2 connector to a SCART AV connector on
VCR/Satellite receiver.
If you have an AV amplifi er
Connect either audio cables from the AUDIO OUT(R/L) jacks
on the HDD & DVD Recorder to the AUDIO IN jacks on your
AV amplifi er, or a digital cable from the DIGITAL AUDIO OUT
(OPTICAL) jack on the HDD & DVD Recorder to the DIGITAL
AUDIO IN jack on your AV amplifi er.
Setup "Video Output" using on-screen menu.
Refer to pages 44~45 of the Instruction Manual for more information.
The Antenna connection does not pass audio/video signals.
To watch a DVD on your TV, you must connect audio/video or Scart cables.
Connecting HDMI/DVI to a TV
Connecting to a TV with HDMI Jack
Using the HDMI cable connect the HDMI OUT terminal on the rear of the
HDD & DVD Recorder to the HDMI IN terminal of your TV.
Press the input selector on your TV remote control until the HDMI
signal from the HDD & DVD Recorder appears on your TV screen.
•
If you use an HDMI cable to connect a Samsung TV to the HDD
& DVD RECORDER, you can operate the recorder using the TV
remote control. (This is only available with SAMSUNG TVs that
support Anynet+.
•
n
Please check the
logo (If your TV has an
supports Anynet+ function.)
Refer to pages 39~40 of the Instruction Manual for more
information.
Connecting to a TV with DVI Jack
Using the DVI Adapter Cable, connect the HDMI OUT terminal on the
rear of the HDD & DVD Recorder to the DVI IN terminal of your TV.
Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the HDD & DVD Recorder to the AUDIO
(red and white) IN terminals of your TV. Turn on the HDD & DVD Recorder and TV.
Press the input selector on your TV remote control until the DVI signal from the HDD & DVD Recorder appears on your TV screen.
M
If the HDD & DVD Recorder is connected to your TV in HDMI 1080p output mode, you must use High speed(category2) HDMI cable.
Connecting a USB memory, MP3 player, Digital Camera to the USB HOST.
You can transfer JPEG, MP3 and DivX fi le of the MP3 player, USB memory or
digital camera to a HDD & DVD RECORDER using the USB interface.
You can also copy JPEG, MP3 and DivX fi le of the HDD & DVD RECORDER to
MP3 player, USB memory or digital camera using the USB interface.
(Refer to page 32 of the instruction Manual for more information)
1.
Connecting a USB memory or other USB device to USB HOST of the
HDD & DVD RECORDER.
Disconnecting the USB cable during the data transfer will stop the
communication and may damage data stored in the memory.
▲ external device
(VCR/Satellite receiver)
To RF IN
▲ HDD & DVD Recorder
n
logo, then it
English-2
Wall
AV amplifier (receiver) ▼
OR
OR
OR
OR
HDMI Cable
(Not Included)
DVI
AdapterCable
(Not Included)
▲ TV
MP3 Player
Digital Camera
▲ HDD & DVD Recorder
▲ TV