Advertisement
15. In the left pane, select Wireless. (Completed screen shown below.)
16. In the Region drop-down field, select a region. Then give the SSID1 a
meaningful name.
17. Click Configure SSID1. The Wireless Security screen appears.
18. From the Security System drop-down field, select WPA2-PSK. Create a PSK
key (pre-shared key) that is greater than 8 characters. Click Save, then Close.
Using the WAP-PLUS as a wireless access point
For specific setup and configuration instructions for your wire-
less camera, refer to the camera's installation guide.
1. If using wireless connectivity, attach the two antennas to the WAP-PLUS.
Orient each antenna vertically and tighten the knurled connectors.
2. Connect the Power Transformer wire to the 12V / 1A connector on the WAP-
PLUS back. Plug the Power Transformer into an outlet.
NOTE: The Power Transformer must be powered by a non-switchable power
outlet.
IMPORTANT:
When setting up a wireless configuration in very large buildings or buildings
with dense walls, wireless communications may be marginal. It is best to first
configure the system in the same room. Then upon successful configuration,
place each wireless camera in the desired location.
If using more than one wireless camera, each must be configured for wireless
security.
If using a router instead of Honeywell's WAP-PLUS, please ensure your router
is configured for DHCP. (This is the default setting for most routers.) If you
are unsure, you can access the router's configuration page and set it for DHCP
if necessary (refer to the router's manual). Since the operation of each router
varies, please refer to the router's manufacturer for support.
Test the system to ensure all cameras exhibit good communications.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been
type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Ê800-11462ÉŠ
800-11462 3/12 Rev. A
19. The Wireless screen returns.
20. In the left pane select Password. If a security log in screen appears. Enter the default User name
(admin) and password (password), then click OK.
21. The Password screen appears.
22. Change the default password and click Save.
23. In the left pane click Log Out, then OK for the confirmation message.
NOTE: You can repeat this procedure for the next WAP-PLUS, or return your PC to a network DHCP state and
reconnect it to the internet or LAN.
Typical configuration using a mix of wired and wireless cameras:
IP
IP
Camera
Camera
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
CLASS B DIGITAL DEVICE STATEMENT
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute
interference reçue y compris les interferences causant une reception indésirable.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2012 Honeywell International Inc.
www.honeywell.com/security
WAN
4
3
2
1
IP
IP
Camera
Camera
IP
Camera
Router
(Configured as a
DHCP server)
WARRANTY
For the latest warranty information go to:
http://www.security.honeywell.com/hsc/resources/wa/
Modem
(Broadband)
Advertisement
