Xlerator XL Installation Instructions Manual

INSTALLATION INSTRUCTIONS FOR
FOR PROPER ELECTRICAL CONNECTIONS, CHECK YOUR LOCAL BUILDING CODES.
YOUR UNIT MUST BE INSTALLED BY A QUALIFIED, LICENSED ELECTRICIAN.
Suggested Mtg. Heights from floor
to bottom of dryer
Men's
Ladies'
Teenagers'
Sm. Children
Handicapped
IF MOUNTING OVER COUNTERTOP, DISTANCE FROM
COUNTER TO DRYER MUST BE 15" (381mm) MINIMUM
Recommended Fastener
Masonry Wall ½" expansion sleeve with ¼" lag bolt
Hollow Wall ¼" wing type through bolt
Wooden Wall ¼" lag screw with washer
1. Remove cover of dryer by unscrewing two tamper-proof bolts from the sides of the cover with the special wrench provided with each unit.
2. Attach wall plate at the four corners to smooth wall. In locations where vandalism is a concern, use the two additional mounting holes shown.
Remove control assembly to access right side mounting hole. Attach with the recommended type of fastener (see above).
3. Connect a 110/120V dryer to a 15 Amp. dedicated branch circuit using at least #12 GA copper wire. (Do not exceed a 20 Amp. branch circuit)
Connect a 208, 220/240V or 277V dryer to no more than a 15 Amp. dedicated branch circuit using at least a #14 GA copper wire.
Attach lines to terminals as indicated by the schematic inside dryer cover. Be sure that an equipment ground wire is securely fastened to green
ground screw on base plate. Dryers should be installed per local code requirements.
4. In multiple installations, before replacing cover, check the Serial Number marked inside the dryer to be sure it matches the Serial Number marked
on the label at the bottom of cover. PLEASE DO NOT SWITCH COVERS. Do not forget to leave the special TAMPER PROOF WRENCH with
the owner.
INSTALLATION NOTE: If the dryer will not turn on, stays on or stops working, it may be mounted too close to a counter or object. Turn off the
power to dryer for 10 seconds and then reapply power. If dryer will start, then turn off again, relocate the object or remount dryer. If this is not
possible, adjust the range of the sensor by turning the range adjustment on the control board, counterclockwise to decrease sensor range.
Please call the factory at 1-800-255-9235 and one of our trained technicians will be happy to assist you.
NOTE: Upon completing installation and checking for proper operation, it is highly recommended that a bead of silicone sealant be placed around
the outside of the cover at the wall to protect dryer from internal corrosion caused by wash water and cleaning solutions
XL14
XL8
XL2
(Location)
45" (1143 mm)
43" (1092 mm)
41" (1041 mm)
35" (889 mm)
37" (940 mm)
XL13 (4)
XL12 (4)
XL6
XL3
XL5
XL4
XL1
XLERATOR
LOCATION OF ADDED MTG
HOLES FOR MORE SECURE
INSTALLATION
XL11 (2)
XL9
XL10
XL7
XL15
HAND DRYER
®
PARTS LIST FOR XLERATOR DRYER
REF NO. DESCRIPTION
XL 1 Cover (includes Nameplate)
XL 2 Nameplate
XL 3 Tamper-proof Bolt
XL 4 Tamper-proof Wrench
XL 5 Air Outlet (includes gasket)
XL 6 Terminal Block (includes screws)
XL 7 Control Assembly & Sensor
XL 8 Heating Element Assembly
XL 9 Motor Assembly
XL 10 Wall Plate Assembly
XL 11 Cover Mounting Brackets
XL 12 Housing Grommet
XL 13 Housing Retainer
XL 14 Recess Kit (for ADA)
XL 15 Optics Assembly (Sensor)
NOTE: Model, Serial Number and Voltage of the
dryer MUST BE included when ordering parts.
XleratorManual3-11.doc
XL