Lan Cable - Sony IPELA PCS-HG90 Connection Setup

3
Connect the Camera Unit.
Connect the Camera Unit and Communication Terminal using the BNC cable and
VISCA cable supplied with the Camera Unit.
Camera Unit
AC power adaptor and power cord **
VISCA RS-422
1 2 3 4 5 6 7 8 9
DC IN 12V
VISCA RS-232C OUT
MONITOR HD-SDI
HFBK-HD1
VISCA cable**
BNC cable**
Communication
VIDEO OUT
HD-SDI HD-SDI HD-SDI Y Pb Pr
Terminal
2 1
SUB MAIN
CAMERA CAMERA
AUDIO OUT REC OUT(MIXED)
1 L R L R L
CAMERA CONTROL
R L
AUX CONTROL CTRL-S
** supplied with the
SUB
Camera Unit
5
Connect the power cord.
Connect the supplied power cord to the Communication Terminal, and then to a wall outlet.
Communication
VIDEO OUT
Terminal
Y Pb Pr Y
(NEAR ONLY)
IO OUT REC OUT(MIXED)
L R L
CAMERA CONTROL
(VISCA)
AUX CONTROL CTRL-S
SUB MAIN
* supplied with the Communication Terminal
to a wall outlet
Notes
• You cannot view the picture from the
camera even if you connect the
Y Pb Pr
Camera Unit directly to the TV monitor.
Be sure to connect the TV monitor to
(NEAR ONLY)
the Communication Terminal.
• Do not connect/disconnect the BNC
100BASE-TX/
cable or VISCA cable with the power
10BASE-T
(VISCA)
on. Doing so may damage the Camera
MAIN
Unit or Communication Terminal.
Pb Pr
~ AC IN
100BASE-TX/
10BASE-T
Power cord*
to a wall outlet
(100 – 240V AC)
4
Connect the Remote Control Receiver and the

LAN cable.

Connect the supplied Remote Control Receiver to the Communication Terminal.
Then, connect the Communication Terminal to a LAN using a LAN cable (not supplied).
Remote Control
Receiver
UTP cable
(category 5, straight)***
VIDEO OUT
Y Pb Pr Y Pb Pr
(NEAR ONLY)
REC OUT(MIXED)
L R L
~ AC IN
CAMERA CONTROL 100BASE-TX/
10BASE-T
(VISCA)
CONTROL CTRL-S
SUB MAIN
Communication
*** not supplied
Terminal
If No Picture Appears on the TV Monitor
The video format of the Communication Terminal is set to "1080/60i" at the factory.
If the video format set on the TV monitor is different from that on the Communication Terminal, no
picture appears on the TV monitor.
Check the video format setting on the TV monitor, and, if necessary, change the video format setting
on the Communication Terminal.
To change the video format on the Communication Terminal
Use the FAR/NEAR button and number buttons 1, 2 and 3 on the supplied Remote Commander.
DISPLAY VIDEO INPUT
CLEAR SYMBOL
PinP FAR/NEAR
FAR/NEAR
BACK ALPHA/
SPACE NUM
button
PUSH
ENTER
RETURN MENU
CONNECT/
DISCONNECT
Number buttons
1, 2, 3
to LAN
The Remote Control Receiver receives
signals from the supplied Remote
Commander. To use the Remote
Commander, point it to the Remote Control
Receiver.
The Remote Control Receiver can be fixed
to a TV monitor, etc. using Velcro.
Note
For safety reasons, do not connect the
100BASE-TX/10BASE-T connector to a
network that applies an excess voltage via
the 100BASE-TX/10BASE-T connector.
Video format
Operation
to be set
1080/60i Press " FAR/NEAR", then press "1" three times.
1080/50i Press " FAR/NEAR", then press " 2" three times.
720/60p Press " FAR/NEAR", then press " 3" three times.
Note
The video format of the signal output from the VIDEO OUT
(NEAR ONLY) connectors is fixed to "720/60p". Use a TV
monitor that supports "720/60p" for the monitor exclusively
for local pictures.