Philips CCK4602 User Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Computer Accessories
  5. CCK4602
  6. User manual
Philips CCK4602 User Manual

Philips CCK4602 User Manual

Cmnd & calibrate
Hide thumbs
Table of Contents

Advertisement

Quick Links

Get support at
http://www.philips.com/support/
http://philips.supportsystem.com/
CMND & Calibrate
Version:
1.0.6
Date:
26 July 2017
Author:
Vincent Storm
CCK4602

User Manual

Advertisement

Table of Contents
loading

Summary of Contents for Philips CCK4602

  • Page 1: User Manual

    Get support at http://www.philips.com/support/ http://philips.supportsystem.com/ CMND & Calibrate CCK4602 User Manual Version: 1.0.6 Date: 26 July 2017 Author: Vincent Storm...

  • Page 2: Version History

    Version history: Version Date Author Changes:  First rework 1.0.1 02/06/2017 Vincent Storm  Layout change 1.0.2 27/06/2017 Vincent Storm  Correction in chapter numbering  Adding General information  Add bold text in Connect COM-port cable 1.0.3 26/07/2017 Vincent Storm ...

  • Page 3: Table Of Contents

    Table of Contents Version history: ............................1 General information ........................3 Introduction ..........................3 Notice ............................3 Help and support ........................3 System requirements ........................4 Package content ..........................4 Software installation ........................4 Specifications ..........................5 Calibrated parameters ......................5 Supported tiling matrix ......................

  • Page 4: General Information

    TP Vision Belgium NV cannot be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible.

  • Page 5: System Requirements

    2. System requirements  Windows 7 (32-bit/64-bit) or Windows 10 (32-bit/64-bit)  DVI / HDMI or DP out  An available RS232 port (USB to RS232 adaptor will also work)  Free memory : 1 GB  Hard disk space : 400MB ...

  • Page 6: Specifications

    5. Specifications 5.1 Calibrated parameters Tint: custom 10000K Gamma: 2.2 Backlight: automatic aligned to the maximum light output 5.2 Supported tiling matrix 1x1 to 15x15 monitors. - 5 -...

  • Page 7: Start The Color Calibration

    6. Start the color calibration Before you start the calibration warm up the monitor(s) for minimum 1 hour. Movie of a 2x2 color calibration 6.1 Connect color sensor 1. Lift up the diffuser arm 2. Rotate the diffuser 3. Click the diffuser in the rear position 4.

  • Page 8: Connect Com-Port Cable

    6.2 Connect COM-port cable  Connect the COM-port from your PC via a null modem (= cross) RS232 cable to the RS232 jack 2.5mm input of the first monitor with monitor ID=1.  Make sure all the monitors are daisy chained via RS232 ...

  • Page 9: Run The Calibration Software

    6.5 Run the calibration software 6.5.1 Start the program  Before you start the calibration warm up the monitor(s) for minimum 1 hour  Start the calibration software CMND & Calibrate 6.5.2 Installation tab  In the “Installation” tab select your COM-port number ...

  • Page 10: Setup Tab

    6.5.3 Setup tab  In the “Setup” tab select your matrix: maximum matrix is 15x15  Point structure: how many points must be aligned in each monitor, recommended value = 5 Note: On the bottom of the window of the program on PC you might see some error in red, adapt where needed according to the errors.

  • Page 11: Calibration Tab

    6.5.4 Calibration tab.  In the “Calibrate” tab select “Calibrate”: this will launch the calibration Note: read first below before starting the actual calibration  A green spot will appear on the first display  Put the color sensor on this green spot and do not take it away ...
  • Page 12 After the calibration is done the green message “Calibrated” will appear on every calibrated monitor. See below screenshot Note: the monitors in the software calibration tool can be deselected, means those monitors will not be calibrated See below screenshot in red marker as an example, monitor “ID: 1” and “ID: 2” will not be calibrated - 11 -...
  • Page 13  Set as reference is used to adjust the backlight of 1 monitor measured from another monitor  it will also adjust the colors to a target value set in the PC  Select in 1 monitor “set as reference”, the light output of this monitor will be measured and used as target value to adjust the other monitor(s) ...

  • Page 14: Manual Tuning

    6.5.5 Manual tuning It is possible to adjust each monitor manually, select your monitor and you can change the “backlight”, the Red, Green and Blue colors manually of the selected monitor, see the red marker below. 7. Supported monitors  65BDL3000Q ...
  • Page 15  BDL6520QL  BDL3260EL  BDL4260EL  BDL4660EL  BDL5560EL  BDL4765EL  Firmware must be at least 1.94 for all above monitors - 14 -...

  • Page 16: Ini File

    8. Ini file Normally you don’t need to change any setting in this ini file. 9. Trouble shooting - 15 -...

Table of Contents