Motorola MK3000 Quick Reference Manual

MK3000
Quick Reference Guide
© 2011 Motorola Solutions, Inc. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Motorola products might be used. An
implied license exists only for equipment, circuits, and subsystems contained in
Motorola products.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are
trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are
used under license. All other trademarks are the property of their respective owners.
Motorola Solutions, Inc.
One Motorola Plaza
Holtsville, N.Y. 11742-1300
http://www.motorolasolutions.com
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty
M olutions, Inc.
otorola S
One Motorola Plaza
Holtsville, New York 11742, USA
1-800-927-9626
http://www.motorolasolutions.com
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo
are trademarks or registered trademarks of Motorola Trademark Holdings,
LLC and are used under license. All other trademarks are the property of
their respective owners. © 2011 M
otorola Solutions, Inc. All rights reserved.
72-148309-01 Revision A — April 2011
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure
that you are adhering to your company's safety programs to prevent employee injury.
•
Reduce or eliminate repetitive motion
•
Maintain a natural position
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
•
Improve work procedures.
Regulatory Information
This device is approved under the Symbol Technologies, Inc. brand: Symbol
Technologies, Inc. is a wholly owned subsidiary of Motorola Solutions, Inc. (collectively
"Motorola").
This guide applies to the following Model Numbers: MK3000, MK3900
All wireless information only applies to MK3900.
All Motorola/Symbol devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://supportcentral.motorola.com
Any changes or modifications to Motorola/Symbol Technologies equipment, not
expressly approved by Motorola/Symbol Technologies, could void the user's authority to
operate the equipment.
Radio Modules
The device contains approved radio module(s). These module(s) are identified below.
Motorola/Symbol SDIO Radio module with 802.11a/b/g Wireless LAN, Type: 21-92955
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the
radio(s) is/are approved for use in the following countries: United States, Canada,
1
Japan, China, S. Korea, Australia, and Europe .
Please refer to the Declaration of Conformity (DoC) for details of other country
markings. This is available at http://www.motorola.com/doc
1
Note : For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria,
Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Country Roaming
This device incorporates the International Roaming feature (IEEE802.11d) which will
ensure the product operates on the correct channels for the particular country of use.
Ad-Hoc Operation (5 GHz band)
Ad-Hoc operation is limited to Channels 36-48 (5150-5250 MHz). Use of this band is
restricted to Indoor Use Only, any other use will make the operation of this device illegal.
Frequency of Operation - FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250
MHz) is restricted to Indoor Use Only; any other use will make the operation of this
device illegal.
Industry Canada Statement:
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce
potential for harmful interference to co-Channel mobile satellite systems. High power
radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz
and 5650-5850 MHz and these radars could cause interference and/or damage to LE-
LAN devices.
Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-
à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces
radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The
range of channels is limited by firmware.
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless
devices.
Potentially Hazardous Atmospheres - Vehicles Use
You are reminded of the need to observe restrictions on the use of radio devices in fuel
depots, chemical plants etc. and areas where the air contains chemicals or particles
(such as grain, dust, or metal powders) and any other area where you would normally
be advised to turn off your vehicle engine.
Potentially Hazardous Atmospheres - Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel
depots, chemical plants etc. and areas where the air contains chemicals or particles
(such as grain, dust, or metal powders).
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or airline
staff. If your device offers a 'flight mode' or similar feature, consult airline staff as to its
use in flight.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical
equipement.
Wireless devices should be switched off wherever you are requested to do so in
hospitals, clinics or healthcare facilitlies. These requests are designed to prevent
possible interference with sensitive medical equipement.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be
maintained between a handheld wireless device and a pacemaker to avoid potential
interference with the pacemaker. These recommendations are consistent with
independent research and recommendations by Wireless Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker
when turned ON.
•
Should not carry the device in a breast pocket.
•
Should use the ear furthest from the pacemaker to minimise the potential for
interference.
•
If you have any reason to suspect that interference is taking place, turn OFF your
device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if
the operation of your wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure - Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices. For information on
"International" human exposure to eletromagnic fields refer to the Motorola/Symbol
Declaration of Conformity (DoC) at http://www.motorola.com/doc.
Europe
To satisfy EU RF exposure requirements, a mobile transmitting device must operate
with a minimum separation distance of 20 cm or more from a person's body.
Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used for this
transmitter must not be co-located or operating in conjunction with any other transmitter/
antenna except those already approved in this filling.
Remote and Standalone Antenna Configurations
To comply with FCC RF exposure requirements, antennas that are mounted externally
at remote locations or operating near users at stand-alone desktop of similar
configurations must operate with a minimum separation distance of 20 cm from all
persons.
Laser Devices
Complies with 21CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007 and EN60825-1:2007 and
IEC 60825-1(ED.2).
The laser classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended
purpose. The following statement is required to comply with US and international
regulations:
Caution: Use of controls, adjustments or performance of procedures other than those
specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light
source, such as the sun, the user should avoid staring directly into the light beam.
Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
CAUTION- CLASS 2 LASER, 1M LED LIGHT WHEN OPEN. DO NOT STARE INTO BEAM
OR VIEW WITH OPTICAL INSTRUMENTS.
ATTENTION- LUMIÉRE LASER DE CLASSE 2 EN CAS D'OUVERTURE. NE PAS
REGARDER DANS LE FAISCEAU.
VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET. NICHT
IN DEN STRAHL BLICKEN.
LED light is emitted from this aperture:
LED Output
This device contains LEDs for illuminating the bar code.
Illumination:
Optical Output: 0.91mW
Pulse Duration: 970uS
Emitted Wavelength: 600-630nm
Viewing the LED output with certain optical instruments (for example, eye loupes,
magnifiers and scopes) may pose an eye hazard.
Caution - Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous LED light exposure.
Power Supply
This device must be powered from an 802.3af or 802.3at compliant power source which
has been certified by the appropriate agencies, or by a LISTED Motorola, Type no.
PWRS-14001 (24Vdc, 1.5A) , direct plug-in power supply, marked Class 2 or LPS
(IEC60950-1, SELV). Use of alternative Power Supply will invalidate any approvals
given to this unit and may be dangerous.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.