Motorola SCANMOD-ET1 Quick Reference Manual

Installation
1. Power off the ET1. 5. Remove the existing module. Do
2. Remove the battery. not remove filler plate.
3. If the handstrap is installed,
rotate the handstrap to access
the expansion module screws.
4. Remove two screws using a T8
®
Torx screwdriver.
6. Install the new module.
Filler Plate
Data Capture
7. Secure the two screws using a
T8 Torx screwdriver.
8. Replace the battery.
MSR Swipe
Additional Information Health and Safety
Recommendations
For detailed information on setting up and using the
Scanning and Scanning/MSR module, refer to the
Ergonomic Recommendations
ET1 Enterprise Tablet User Guide and Integrator
Guide.
In order to avoid or minimize the
CAUTION
Regulatory Information
potential risk of ergonomic injury
This device is approved under Motorola Solutions, follow the recommendations below.
Inc. Consult with your local Health &
This guide applies to the following model numbers: Safety Manager to ensure that you
SCANMOD-ET1 and MSRSCAN-ET1. are adhering to your company's
All Motorola devices are designed to be compliant safety programs to prevent
with rules and regulations in locations they are sold employee injury.
and will be labeled as required.
• Reduce or eliminate repetitive motion
Local language translations are available at the
• Maintain a neutral postures
following website:
• Reduce or eliminate excessive force
http://supportcentral.motorola.com.
• Keep objects that are used frequently within easy
Any changes or modifications to Motorola
reach
equipment, not expressly approved by Motorola/
• Perform tasks at correct heights
Symbol Technologies could void the user's authority
• Reduce or eliminate vibration
to operate the equipment.
• Reduce or eliminate direct pressure
For use only with Motorola approved and UL Listed
• Provide adjustable workstations
mobile computers. Motorola approved and UL Listed
• Provide adequate clearance
accessories and/or Motorola approved and UL
• Provide a suitable working environment
Listed/Recognized battery packs.
• Improve work procedures
Declared maximum operating temperature: 50 °C.
Laser Devices
Class 2 laser scanners use a low power, visible light
diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into
the light beam. Momentary exposure to a Class 2
laser is not known to be harmful.
CAUTION: Use of controls, adjustments or
Radio Frequency Interference
performance of procedures other than those
Requirements-FCC
specified herein may result in hazardous laser light
exposure.
Note: This equipment has been
Labeling
tested and found to comply with
the limits for a Class B digital
device, pursuant to Part 15 of
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
the FCC rules. These limits are designed to provide
1 STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER DE
CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER
DANS LE FAISCEAU.VORSICHT- LASERLICHT KLASSE 2, reasonable protection against harmful interference
WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL
BLICKEN.
2 COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR in a residential installation. This equipment
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED
JUNE 24, 2007 AND IEC 60825-1 (Ed.2.0),EN60825-1:2007 &
IEC62471:2006 (Ed. 1.0) EN62471:2008. generates, uses and can radiate radio frequency
LASER LIGHT- DO NOT STARE INTO BEAM.
energy and, if not installed and used in accordance
3 CLASS 2 LASER PRODUCT. LASERLICHT - NICHT
IN DEN STRAHL BLICKEN. LASER KLASSE 2.
LUMIÈRE LASER - NE PAS REGARDER DANS with the instructions, may cause harmful interference
LE FAISCEAU. APPAREIL À LASER DE
CLASSE 2 630-680nm, 1mW
to radio communications. However there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Label read:
• Reorient or relocate the receiving antenna
1. CAUTION - CLASS 2 LASER LIGHT WHEN
• Increase the separation between the equipment
OPEN. DO NOT STARE INTO BEAM.
and receiver
2. COMPLIES WITH 21CFR1040.10 AND 1040.11
• Connect the equipment into an outlet on a circuit
EXCEPT FOR DEVIATIONS PURSUANT TO
different from that to which the receiver is
LASER NOTICE NO. 50, DATED JUNE 24, 2007
connected
AND IEC 60825-1 (Ed.1.2, 2.0); EN60825-
• Consult the dealer or an experienced radio/TV
1:2001, 2007 & IEC62471 (Ed.1.0);
technician for help.
EN62471:2008.
3. LASER LIGHT - DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT.