Sharp AN-3DG40 Operation Manual

MODEL
AN-3DG40
3D GLASSES FOR
SHARP 3D AQUOS
OPERATION MANUAL
ENGLISH
These 3D Glasses (AN-3DG40) are only for use with SHARP AQUOS LCD
TVs supporting 3D. For details of how to make adjustments for 3D functions
and to fully enjoy 3D viewing, refer to the operation manual of your TV.
IMPORTANT INFORMATION
This product contains a CR Coin Lithium Battery which contains
Perchlorate Material – special handling may apply, California residents,
See www.dtsc.ca.gov/hazardouswaste/perchlorate/
U.S.A. ONLY
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
"This product contains a coin/button cell battery. If the coin/button cell battery
is swallowed, it can cause severe internal burns in just 2 hours and can lead
to death. Keep new and used batteries away from children. If the battery
compartment does not close securely, stop using the product and keep it
away from children. If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate medical attention."
Printed in China
13P02-CH-NM
ATI3045-500030
EN-1
Using the 3D Glasses
CAUTION
• Not all consumers can experience and enjoy 3DTV. Some people suffer from stereo blindness which
prevents them from perceiving the intended depth of 3D entertainment. Also, some people who watch 3D
programming may experience initial feelings of motion sickness as they adjust to the picture. Others may
experience headaches, eye fatigue or motion sickness. Some viewers might also experience epileptic
seizures. Like a roller coaster, the experience is not for everyone.
• The 3D Glasses are precision equipment. Handle them with care.
• Improper use of the 3D Glasses or failure to follow these instructions can result in eye strain.
• If you experience dizziness, nausea, or other discomfort while viewing 3D images, immediately
discontinue use of the 3D Glasses. Using the 3DTV with incompatible 3D broadcasts or software can
make images appear blurry or create overlapping images.
• When viewing 3D images continuously, be sure to take a break periodically to prevent eye strain.
• If you are nearsighted or farsighted or have astigmatism or a different level of eyesight between the
left and right eyes, you should take the necessary steps, such as wearing eyeglasses, to correct your
eyesight before viewing 3D images. The 3D Glasses can be worn over eyeglasses.
• When viewing 3D images, keep the 3D Glasses horizontally level with the TV screen. If you tilt the
3D Glasses with respect to the TV screen, the images viewed by the left and right eyes may appear
significantly different or images may appear overlapping.
• View 3D images at the appropriate distance from the TV screen. The recommended distance is three
times the effective height of the TV screen.
• Be careful of your surroundings when viewing 3D images. When you view 3D images, objects may appear
closer or farther than they are. This may cause you to misjudge the distance and possibly result in injury
if you accidentally hit the screen or surrounding objects.
• The 3D glasses are not recommended for people aged less than 6.
• When children are viewing 3D images, be sure a parent or guardian is present. Monitor children viewing
3D images, and if they show signs of discomfort, immediately discontinue use of the 3D Glasses.
• People with a known history of photosensitivity and people with heart problems or poor health should
not use the 3D Glasses. This can worsen existing health conditions.
• Do not use the 3D Glasses for other purposes (such as general eyeglasses, sunglasses, or protective
goggles).
• Do not use the 3D function or 3D Glasses while walking or moving around. This may result in injuries due
to running into objects, tripping, and/or falling.
• When using the 3D Glasses, take care not to accidentally strike the TV screen or other people. Viewing
3D images may cause you to misjudge the distance to the TV screen and accidentally strike the screen,
resulting in possible injury.
• It is recommended that you do not view 3D images if you are sleep deprived or if you have been drinking
alcohol.
Supplied Accessories
Make sure the following accessories are provided with the 3D Glasses.
3D Glasses Nose pad* Glasses case
(×1) (small ×1, large ×1) (×1)
Operation manual
(this publication)
Cleaning cloth
(×1)
* Use the 3D Glasses nose pad as needed. The small nose pad is already attached.
NOTE
• The illustrations above are for explanation purposes and may vary slightly from the actual accessories.
EN-5
Specifications
ENGLISH
P o r d u t c 3 D G a l s s s e
Model number AN-3DG40
Lens type Liquid crystal shutter
Power supply DC3V
B t a e t y r L h t i u i m b t u o t n b t a e t y r C ( R 2 0 2 5 × ) 1
Battery life Approx. 100 hours of continuous use
Dimension (W x H x D) 6 / × 1 / × 6 / inche/171.2 × 46.0 × 162.4 mm
3 5 2
4 6 5
W e g i t h A p p o r . x 0 0 . 6 8 3 b l . s 3 / 1 0 . g n i ( c u l d n i g h t l e h t i u i m b t u o t n b t a e t ) y r
Operating temperature 50°F to 104°F/10°C to 40°C (The 3D Glasses cannot operate fully at extreme high
or low temperatures. Please use them within the specified usage temperature
range.)
The product serial number is displayed on the 3D Glasses as indicated in the illustration on
the left. The first three digits represent the date of manufacture.
Example: Manufactured on February 23, 2013
S/N : 8 2 P
Manufacture number
Month of Day of
manufacture manufacture
1: 1 1: 1 A : 10
2: 2 2: 2 B : 11
3: 3
3: 3
H : 17
8 : 8 J : 18
9 : 9
A : 10 N : 22
B : 11 P : 23
C : 12
W : 30
X : 31
* "I", "O", "Y" and "Z" are not used.
NOTE
• Please contact your local authority for the correct method of disposal of this product and/or packing.
Usage Range of the 3D Glasses
The 3D Glasses can be used by receiving a signal sent from the TV.
The 3D Glasses turn off automatically after 15 seconds if no signal is received from the TV.
Operating range
From directly in front of the 3D emitter on the TV: approx.17 ft (5 m)
(within approx. 30° horizontally and 20° vertically)
IMPORTANT INFORMATION
(U.S.A. and Canada only)
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement
This Class B digital apparatus complies with CAN ICES-003(B)/NMB-3(B)
DEAR SHARP CUSTOMER
Thank you for your purchase of the 3D Glasses for SHARP 3D AQUOS. To ensure safety and many years of
trouble-free operation of your product, please read the Important Safety Instructions carefully before using
this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong
the service life of your Liquid Crystal Television, please read the following precautions carefully before using the
product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
EN-2
Using the 3D Glasses
Part Names
1 Power button 1 Power button
• When the power button is pressed for 2 or more
seconds with the power off, pairing with the TV starts.
2
LED indicator • When the power button is pressed for 2 or more
seconds with the power on, the power turns off.
• When paired, the power will turn off if the power
button is pressed for 2 or more seconds.
• When the power button is pressed for less than
2 seconds with the power off, the 3D glasses
will turn to standby.
• When the 3D glasses are in 3D mode with the
power on, pressing the power button for less than
2 seconds will turn the 3D glasses to 2D mode.
• When the 3D glasses are in 2D mode with the
power on, pressing the power button for less than
two seconds will turn the 3D glasses to 3D mode.
• When paired, the 3D glasses will be non-reactive if
the power button is pressed for less than 2 seconds.
2 LED indicator
• When paired with the TV, the LED light
blinks in red and green.
• When pairing is completed successfully,
3
Nose pad mount the LED blinks in green for 3 seconds.
• When the power is turned on, the LED
NOTE
lights up in green for 3 seconds.
• The power turns off automatically in the following
• When in 3D mode, the LED blinks in green
cases:
in 3-second intervals.
- When pairing fails
• When in 2D mode, the LED blinks in red in
- When the 3D Glasses are not operated in standby
3-second intervals.
for 15 seconds
• When the power is turned off, the LED
blinks in green 3 times.
NOTE
• When in low voltage mode:
- When in 3D mode, the LED blinks 3 times in
green in 3-second intervals.
- When in 2D mode, the LED blinks 3 times in red
in 3-second intervals.
3 Nose pad mount
The dedicated nose pad can be mounted here.
Attaching the Nose Pad Before Using the 3D Glasses
Attach either of the supplied nose pads as needed (such Before using the 3D Glasses for the first time, remove the
as when the glasses do not fit properly). The glasses insulating sheet attached to them.
come with a large and small nose pad.
Removing the nose pad Attaching the nose pad
EN-6
Fiche technique
FRANÇAIS
P o r d t i u L u n e t t s e 3 D
Numéro de modèle AN-3DG40
Type de verres Obturateur à cristaux liquides
Alimentation 3 V CC
P e l i P e l i b o u o t n a l u h t i u i m C ( R 2 0 2 5 × ) 1
Durée de vie de la pile Environ 100 heures d'utilisation continue
Dimensions (L x H x P) 6 / × 1 / × 6 / pouces/171,2 × 46,0 × 162,4 mm
3 5 2
4 6 5
P o d i s E v n o r i n 0 0 , 6 8 3 b l . s 3 / 1 0 , g ( v a c e a l l i p l e h t i u i m - o i n p o y l m è e r r c e h a g r a e b ) e l
Température de 50 °F à 104 °F/10 °C à 40 °C (Les lunettes 3D ne peuvent fonctionner pleinement à
fonctionnement des températures extrêmement élevées ou basses. Veuillez les utiliser dans la plage de
température d'utilisation spécifiée.)
Le numéro de série du produit est affiché sur les lunettes 3D conformément à l' illustration de
gauche. Les trois premiers chiffres représentent la date de fabrication.
Exemple : Fabriquée le 23 février 2013
S/N : 8 2 P
Numéro de fabrication
Mois de Jour de
fabrication fabrication
1: 1 1: 1 A : 10
2: 2 2: 2 B : 11
3: 3
3: 3
H : 17
8 : 8 J : 18
9 : 9
A : 10 N : 22
B : 11 P : 23
C : 12
W : 30
X : 31
utilisées.
REMARQUE
• Veuillez contacter votre municipalité locale pour connaître la méthode correcte de mise au rebut de ce produit et/ou
de son emballage.
Portée d'utilisation des lunettes 3D
Les lunettes 3D peuvent être utilisées en recevant un signal envoyé par le téléviseur.
Les lunettes 3D s'éteignent automatiquement au bout de 15 secondes en l'absence de signaux émis par le téléviseur.
Rayon d'action
Directement depuis l'avant de l'émetteur 3D sur le téléviseur : environ 17 pieds (5 m)
(dans une plage d'environ 30° horizontalement et 20° verticalement)
IMPORTANT SAFETY INSTRUCTIONS
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Prevention of accidental ingestion
• Keep the accessory out of the reach of small children. Small children can accidentally swallow these parts.
−If a child accidentally swallows any of these parts, seek immediate medical attention.
Do not disassemble
• Do not disassemble or modify the 3D Glasses except when recycling the batteries. Do not modify the 3D
glasses.
Caution for lithium battery
• Batteries must not be exposed to excessive heat such as direct sunlight or fire.
• Replace only with the same or equivalent type of battery. The battery may explode if improperly replaced.
• Take care not to reverse the battery poles (+ and –) when loading the battery. Follow the correct procedure when
loading the battery. Loading the battery incorrectly may damage the battery or cause it to leak battery fluid,
which could result in a fire, injury or damage.
Handling the 3D Glasses
• Do not drop, exert pressure on, or step on the 3D Glasses. Doing so may damage the glass section, which may
result in the risk of injury.
• Be careful not to trap your finger in the hinge section of the 3D Glasses. Doing so may result in injury.
−Pay special attention when children are using this product.
Using the 3D Glasses
• Use of the 3D Glasses should be limited to a maximum of 3 hours, and in any case no more than one movie.
• Use the 3D Glasses only for the specified purpose.
• Do not move around while wearing the 3D Glasses. The surrounding area may appear dark, which may result in
falling or other accidents that may cause injury.
Caring for the 3D Glasses
• Use only the cloth provided with the 3D Glasses to clean the lenses. Remove dust and soil from the cloth. Any
dust or other soiling on the cloth may result in scratches. Do not use solvents such as benzene or thinners as
doing so may damage the coating.
• When cleaning the 3D Glasses, take care not to allow water or other fluids to come into contact with the
glasses.
• Always store the 3D Glasses in the case provided when not in use.
• When storing the 3D Glasses, avoid very humid or hot locations.
Viewing 3D images
• If you experience dizziness, nausea, or other discomfort while viewing 3D images, discontinue use and rest your
eyes.
• Do not use the 3D Glasses if they are cracked or broken.
EN-3
Using the 3D Glasses
Using the 3D Glasses Replacing the Battery
The battery has an expected service life of approximately
100 hours.
• When replacing the button battery, use only the
designated battery (Maxell branded CR2025 lithium
button battery).
1
Use the tip of a ballpoint pen or similar object to
press in on the lock.
Pairing the 3D glasses
To view 3D images, it is necessary to pair the 3D glasses
and TV.
• To confirm pairing of the 3D glasses and TV, make sure
that 3D images are displayed on the TV screen.
• When the power button is pressed for 2 or more 2
While pressing in on the lock, place your fingertip
seconds with the power off, pairing with the TV starts.
in the groove and pull out the battery holder.
When pairing is completed successfully, the LED blinks
• Pull the battery holder all the way out.
in green for 3 seconds.
• To switch between 2D and 3D modes, briefly press the
power button.
1'64" (50 cm)-6'56" (2 m)
3
Replace the battery.
1Use the tip of a ballpoint pen or similar object to
remove the battery.
2Insert a new battery.
• Insert the battery with the negative side facing up.
NOTE
1 2
• When paired, make sure that the 3D glasses are kept
at a distance of 1.64-6.56 ft (50 cm-2 m) from the TV.
If too close, pairing cannot be performed.
Switching to 3D and 2D Mode
4
Align the battery holder with the battery slot on the
When viewing 3D images, you can press the power
3D Glasses and slide it back into place.
button to switch between 2D and 3D modes. This is
• Press it in until it locks.
useful when several people are viewing 3D images on the
same TV with some people wanting to watch in 3D and
some people wanting to watch in 2D.
Viewing 2D images
When you press and hold the power button for less
than 2 seconds while viewing 3D images, the LED
light blinks in red and the 3D images switch to 2D
images.
Viewing 3D images
When you press and hold the power button for less
than 2 seconds while viewing 2D images, the LED
light blinks in green and the 2D images switch to NOTE
3D images.
• Take care not to reverse the battery poles ( and
when loading the battery.
• Used batteries should be disposed of strictly in
accordance with the applicable local laws and regulations.
EN-7
Especificaciones
ESPAÑOL
P o r d u c o t G f a s a p a a r 3 D
Número de modelo AN-3DG40
Tipo de lente Postigo de cristal líquido
Suministro de alimentación 3 V CC
P a l i P a l i d e b o ó t n d e i l o i t C ( R 2 0 2 5 × ) 1
Vida de la pila Aprox. 100 horas de uso continuo
Dimensiones (An x Al x Pr) 6 / × 1 / × 6 / pulgadas/171,2 × 46,0 × 162,4 mm
3 5 2
4 6 5
Peso Aprox. 0,0683 libras/31,0 g (incluyendo la pila recargable de polímero de iones de litio)
Temperatura de 50°F a 104°F/10°C a 40°C (Las gafas para 3D no pueden funcionar perfectamente
funcionamiento a temperaturas extremadamente altas o bajas. Use las gafas dentro de la gama
especificada de temperaturas de uso).
El número de serie del producto se muestra en las gafas para 3D como se indica en la ilustración
de la izquierda. Los primeros tres dígitos representan la fecha de fabricación.
Ejemplo: Fabricadas el 23 de febrero 2013
S/N : 8 2 P
Número de fabricación
Mes de Día de
fabricación fabricación
1: 1 1: 1 A : 10
2: 2 2: 2 B : 11
3: 3
3: 3
H : 17
8 : 8 J : 18
9 : 9
A : 10 N : 22
B : 11 P : 23
C : 12
W : 30
X : 31
* "I", "O", "Y" y "Z" no se usan.
NOTA
• Para información sobre el método correcto para deshacerse de este producto y/o embalaje, contacte con las
autoridades locales.
Alcance de uso de las gafas para 3D
Las gafas para 3D pueden usarse para recibir una señal enviada desde el televisor.
Las gafas para 3D se apagan automáticamente después de 15 segundos sin recibir señal desde el televisor.
Alcance de operación
Desde directamente delante del emisor 3D en el televisor: aproximadamente 17 pies (5 m)
(dentro de aproximadamente 30° horizontalmente y 20° verticalmente)
SHARP CORPORATION
IMPORTANT SAFETY INSTRUCTIONS
Notes on Radio Wave Certification in the U.S.A. and Canada
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
"This transmitter must not be co-located or operated in conjunction with any other anntenna or transmitter."
FCC/INDUSTRY CANADA NOTICE
This device complies with Part 15 of FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency
(RF) Exprosure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of
specific absorption ratio (SAR).
FCC CAUTION
Changes or modifications not expressly approved by Hosiden responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003
Le présent appareil est conforme aux la prtie 15 des règles de la FCC et CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'uitilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées pour un environnement non
contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans le Supplément C
à OET65 et d'exposition aux fréquences radioélectriques (RF) CNR-102 de l'IC. Cet équipement émet une énergie RF
très faible qui est considérée conforme sans évaluation du débit d'absorption spécifique (DAS).
Cet appareil numérique de la classe B est conforme à la norme NMB-3 du Canada.
Notas sobre la Certificación de Radiodifusión en México
• COFETEL: RCPHOAR12-1504
• Nombre de la marca del módulo con licencia: SHARP CORPORATION
• Nombre de modelo del módulo con licencia: ARC0517
• Módulo ARC0517 instalado adentro de esta gafas
PRECAUCIÓN
"La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo
no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada."
Número de licencia para la certificación de radiodifusión
Estados Unidos CONTAINS FCC ID: VIYARC0517
Canadá CONTAINS IC: 7305A-ARC0517
EN-4
Using the 3D Glasses
NOTE
• These 3D Glasses are only for use with SHARP LCD TVs supporting 3D.
3D Glasses lenses
• Do not apply pressure to the lenses of the 3D Glasses. Also, do not drop or bend the 3D Glasses.
• Do not scratch the surface of the lenses of the 3D Glasses with a pointed instrument or other object. Doing so may
damage the 3D Glasses and reduce the quality of the 3D image.
• Use only the cloth provided with the 3D Glasses to clean the lenses.
Caution during viewing
• Do not use devices that emit strong electromagnetic waves (such as cellular phones or wireless transceivers) near
the 3D Glasses. Doing so may cause the 3D Glasses to malfunction.
• The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them within the specified
usage temperature range.
• If the 3D Glasses are used in a room with fluorescent lighting, the light within the room may appear to flicker. In this
case, either darken or turn off the fluorescent lights when using the 3D Glasses.
• Wear the 3D Glasses correctly. 3D images will not be correctly visible if the 3D Glasses are worn upside down or
back-to-front.
• Other displays (such as computer screens, digital clocks, and calculators) may appear dark and difficult to view while
wearing the 3D Glasses. Do not wear the 3D Glasses when watching anything other than 3D images.
• If you lie on your side while watching the TV with 3D Glasses, the picture may look dark or may not be visible.
• Be sure to stay within the viewing angle and optimum TV viewing distance when watching 3D images. Otherwise,
you may not be able to enjoy the full 3D effect.
• The 3D Glasses may not work properly if there is any other 3D product or electronic devices turned on near the
glasses or TV. If this occurs, turn off the other 3D product or electronic devices or keep the devices as far away as
possible from the 3D Glasses.
• Stop using this product in any of the following situations:
−When images consistently appear doubled while you are wearing the 3D Glasses
−When you have difficultly perceiving the 3D effect
• If the 3D Glasses are faulty or damaged, stop using them immediately. Continued use of the 3D Glasses may cause
eye fatigue, headaches and illness.
• If you have any abnormal skin reaction, stop using the 3D Glasses. In very rare instances, such reactions may be
due to an allergic reaction to the coating or materials used.
• If your nose or temples become red or you experience any pain or itchiness, stop using the 3D Glasses. Pressure
caused by long periods of use may lead to such reactions and may result in skin irritation.
Troubleshooting
P o r b e l m P o s s b i e l S l o t u o i
• Images displayed in 3D mode • Is the power of the 3D Glasses turned on?
appear doubled while you are • Press the power button for at least 2 seconds to turn on the 3D
wearing the 3D Glasses. Glasses.
• Images displayed in 3D mode • Are the 3D Glasses set to 2D mode?
appear 2D while you are wearing • Press the power button while viewing 2D images, the LED light blinks in
the 3D Glasses. green and the 2D images switch to 3D images.
)
EN-8
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer
assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original
container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or
part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has been removed, defaced,
changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This limited warranty will not apply if the Product has
been or is being used in a commercial setting or application; this warranty is meant solely for the non-commercial, household use of the Product by consumers in
their home or residence. If you intend to or already use this Product for commercial purposes or in a commercial setting, there are warranties available to cover
your use of this Product, the terms of which may vary. Please contact 1-888-GO-SHARP for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of purchase to the servicer,
which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or implied. Specifically ALL
OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE
LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE
PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser and
only for the time periods set forth herein. No other representations or promises made by anyone are permitted. Correction of defects, in the manner and for the
period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and
shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable,
or in any way responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence, lack of
reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the Product which were caused by
repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on remedies for breach in certain transactions; in such states, the
limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA. AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description: AN-3DG40 3D Glasses
(Be sure to have this information and Proof of Purchase available when you need service
for your Product.)
Warranty Period for this Product: One (1) year parts and labor from date of purchase.
Additional Exclusions: User replaceable batteries are not covered by this Limited Warranty.
What to do to Obtain Service: Warranty service is available from a Sharp Authorized Service Center located in the United
States.
To receive repair handling instructions, please contact Sharp toll free at 1-800-BE-SHARP
(1-800-237-4277).
If it is necessary to ship the Product for servicing, please ensure it is shipped prepaid,
insured and packaged securely. Sharp shall not be responsible for lost, stolen or
misdirected mail or for damage to the product incurred during shipping. Please have
proof of purchase available when requesting warranty service.
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES, CALL 1-800-BE-SHARP OR VISIT www.sharpusa.com
n
For USA customers only