1. FEATURES 1.1 System Features Feature Standard (specifications) Option Processor AMD 5X86 133MHz BIOS • 4MB DRAM (expandable to 32MB) with Memory two 72-pin SIMM sockets • 32KB non-volatile memory (expandable to 128KB) Expansion Slots two 16-bit ISA or one 16-bit ISA and 1 PCI RS232C Ports 4 Internal and 4 External (with power output)
Figure 1.1 Isometric View Accessories 1) Journal spooler 2) Roll paper spndle 3) Roll paper 4) Printer ribbon (SA-5000 only) 5) Mode key (3 type x 2 set) 6) Printer cover / FDD cover key 7) Note clip — 2 —...
Page 5
BACK VIEW Expansion Brackets Customer Display Cash Drawer Ports Port Serial Ports Power Supply Ethernet LED Indicator Parallel Port VGA CRT Port Connector Figure 1-2 Figure 1-1 gives an isometric view of the system. On the front, the Floppy Disk Drive cover can be locked up with a keylock.
9.5” monochrome LCDor 10.4” Color DSTN LCD The LCD panel can be rotated, tilted or slid horizontally. The SA-5000 mounts the monochrome video BIOS ROM and the SA-5100 mounts the colour video BIOS ROM as standard. For flexible system configuration, monochrome or colour LCD display is available for both models by switching video BIOS ROM and jumper setting on the motherboard (JP31, JP46).
Page 7
1-3-7. Printers The system housing is designed to accommodate different printer mechanisms with different covers as indicated in the table below. Model Type of Printer Printer Mechanism SA-5000 Single Station Dot Matrix Citizen-614 with validation SA-5100 Single Station Thermal Citizen-380...
Page 8
1-3-8. Cash Drawers The system can support up to two cash drawers. 1-3-9. Ethernet The system provides a 10Mbps connectivity to a Local Area Network complying with the IEEE802.3 Ethernet standard. The Ethernet controller adopts a Bus-Master approach for maximum throughput on the ISA bus. Driver information need to be specified.
2. SPECIFICATIONS 2-1. SA-5000 / 5100 unit Environment and Safety Specifications Specifications Operating Temperature 5˚C — 35˚C Operating Humidity 20% to 90% Non Cond. RH Storage Temperature -10˚C — 80˚C FCC Class A CE Mark Safety & ESD cUL1950, GS...
1. Connect the power cable protruding from the neck of the top assembly to the power cable of the system assembly. 2. Then connect the signal cables protruding from the neck of the top assembly to the signal cables of the system assembly.
4-3. Customer display (SA-5060N, SA-5061D, SA-5062DH) Customer Display (Top Assembly) Neck 10-pin Ribbon Connector Take top cover on upper case and screw pole kit. Thread display cable(s) into case System Assembly Installing Customer Display to System 1. Alphanumeric 2x20 type (SA-5061D, SA-5052DH) Connect the 10-pin ribbon cable to the 10-pin connecter on the rear panel.
Page 14
2. Numeric 1x11 type (SA-5060N) 1. Connect 2 pcs of expansion cable which is the SA-5060N carton box to SA-5060N. 2. Open the upper case and release the screw to fixing the bracket. 3. Change the bracket which is in the SA-5060N carton box and insert the cable to the hole. 4.
Page 15
PCB LOCATION Printer controll PCB CONNECTOR LOCATION Connect 2 pcs of cable here. Note : In case the SA-5060N has no replacement bracket in the carton, please remove the cover for expansion board. Then, insert the cable this hole. Remove this cover and insert 2 pcs of cable here.
Connector SYSTEM REAR VIEW SA-5000/5100 have two cash drawer ports located at the rear of the system. A maximum of two cash drawers can be connected to the system through these ports. Note: Type of connector for the Ethernet port is similar to connector for the cash drawer.
5-2. Motherboard block diagram for serviceing porpose M1489 M1487 DRAM No room to mounting CD-ROM M1489 / M1487 System Block Diagram M1489CMP : Controls cache memory and PCI bus M1487IBC : ISA bus controller RTC : Real time clock (Dallas DS12887A ) CD ROM : CD ROM is used for serviceing purpose.
5-3. Motherboard Jumper and Connector position POWER SUPPLY TO KEYBOARD FLOPPY DISK DRIVE BATTERY POWER SUPPLY FOR GUS HARD DISK DRIVE PRINTER CUSTOMER DISPLAY KEYBAORD CONTROLLER VGA BIOS SYSTEM BIOS MONO LCD COLOR LCD MEMORY SOCET COMSTRAST EXT SERIAL 1 J17 VGA LED1 J12 VGA...
5-4. Jumper Settings Change the jumper settings for each type of CPU used according to the table below. CPU TYPE SETTING 486DX F P24C P24D P24T AMD+ 5x86 Fit F Fit F Fit F Fit F 1-3, 5-6 1-3, 5-6 :default Fit = Fitted / N-F = Not Fitted / Default setting is marked by an AT-sign F / JP9 Fitted for Write Thru, Not Fitted for Write Back / JP39 1-3 Fitted for 133 MHz...
Page 21
Description for DS12887 for DS12887A CMOS Reset (do not insert) for GUS for Mistoffelees Power Switch Status Detection INTEL CPU * TI CPU Backup Status Ring Indicator Int. Serial Port #3 Pin 9 +12V Carrier Detect Int. Serial Port #3 Pin 1 3.45V 3.3V 3.3V/3.45V CPU Volt Selection...
Page 22
The table below shows a summary of all jumper description. PINS WHAT FOR CMOS Reset (not to be inserted) System Reset (not to be inserted) Power Switch Status Detection Backup Status Internal Serial Port #3 - pin 1 & pin 9 selection (5V) Speaker Bypass CPU Voltage Selection CPU Type Selection...
5-5. Interface Specifications Connector Connector Serial Port w/o Voltage Supply External VGA Printer Non-existent Serial Port w/ Voltage Supply Non-existent Serial Port w/ Voltage Supply Non-existent Serial Port w/ Voltage Supply Non-existent Keyboard Interface Non-existent Contrast Voltage Adjustment Non-existent Color LCD Display Non-existent Monochrome LCD Display Serial Port for Smart Card (see J3)
Page 24
5-5-2. LCD VGA Ports J9 - Color LCD Display J10 - Monochr. LCD Display DL4 - Display Data Signal Scan Start-up Signal Input Data Latch Data Input Clock Scan Start-up Signal Input Data Latch VEE - Power supply for LCD Data Input Clock Contrast Adjust Voltage DU3 - Display Data Signal...
Page 25
5-5-3. VGA Ports J12 - VGA (D-Sub 15pin) J26 - Header 10pin Green Blue HSync VSync [VGA Connection] 5-5-4. Serial Ports Serial Port Default Peripheral Location on M/B +12V, +5V Customer Display Default Default POS Printer Selectable Default User-defined J14 & J25 Selectable (0.5A Fuses) User-defined Selectable (0.5A Fuses)
Page 26
Ext. Port #1 Ext. Port #2 Ext. Port #3 Ext. Port #4 +12V/CD +12V/CD +5V/RI +5V/RI [Another 4 of the Serial Ports] 5-5-5. Ethernet Port The connector used conforms to the industry-standard RJ-45. Refer to the relevant documents. 5-5-6. Drawer Port Pin Number Signal Name Signal Direction...
5-6. Memory map The memory system is that of the IBM AT PC-compatible. The size of the system memory depends on the size of the SIMM fitted. See the figure below. 00000 640KB CONVENTIONAL MEMORY A0000 VIDEO BUFFER & EXPANSION AREA D8000 32K NVRAM E0000...
5-7. Serial Port Assignments For convenience, the serial port table is reproduced here. The serial ports for the optional operator display and the 2x20 customer display are controlled by ACER M5105-A4 controller chip. These ports support only IRQ3 and IRQ4 and can go up to 56Kbps. Location Default Device Selectable...
5-9. Power supply circuit R14A R14B AC L +12 V DC+12V AC N +5 V DC+5V R12A R12B DC-5V –5 V R10 L3 DC-12V –12 V +24 V DC+24V DC+24V VR51 Point Voltage level (V) DC180 - 190V DC180 - 190V Less than 30V (Pulse) Q1(D-S) 350 - 400V (Pulse)
5-10. Printer control PCB(SA-5000) The following circuit is printer control circuit for SA-5000. Color change Paper feed Head driver Motor PRINTER CN7-14 Sol.No1 ENA1 COM1 ˚ CN7-6 Sol.No2 OUT1 OUT2 CN7-13 Sol.No3 OUT3 4.7K OUT4 CN7-7 Sol.No4 IC6A 74LS06 2SD1827...
5-11. Printer control PCB(SA-5100) The following circuit is for printer control for SA-5100. Head temperature detection 10 µF/16 V 100 µF/50 V 2SA1115 0.01 µF 4.7K 0.1 µF 0.1 µF 10 µF/16 V JUMPER 100K 22 K 100K 0.1 µF AGND PGND RD3.9EB2 AGND...
Page 33
Data buffer for graphic data : 64KB (32KB x 2) 74AC32 AD[0..15] A[0..20] 0000H-7FFFH 0000H-7FFFH 10000H-17FFFFH 10000H-17FFFFH Even AD10 AD11 AD12 AD13 AD14 AD15 0.1 µF 0.1 µF M5M5256AFP-10L M5M5256AFP-10L U14A U14B WRO# R/W# 74AC32 74AC32 U14C U14D WRO# BHE# 74AC32 74AC32 0.1 µF...
6. To open / close the upper case CAUTION : Make sure that the hard disk drive is complete stop before open tha upper case. Otherwise, the HDD might be defect. Leave the machine about 40 seconds after power turned off. 1.
Page 37
2. In case the power supply unit is replaced, do not close the air hole of power supply unit. Air hole 3. To close the upper case, please be careful not to catch the cable between cases or metal plate when closing the case.
7. RESET OPERATION 7-1. Hard reset It works as PC reset button. 1. Open the upper case. 2. Make short the terminals of JP2 by metal tweezers on the motherboard and turn the power the power switch on. 3. Wait for 5 seconds and release the tweezers, then hard reset is performed. 7-2.
7-4. BIOS Setup This chapter provides the user relevant information on setting the BIOS. The system BIOS used is from AMI. The following is a list of BIOS modifications for the system. • System setup • Chipset setup • Support a maximum of 8 serial ports •...
Page 40
7-4-2. BIOS setup operation To change the BIOS setup menu 1. Turn the mode key to “5” position. 2. Turn the power switch on. 3. Press “5” button when the AMI BIOS screen appears on the LCD display. 4. Then main menu appears on the LCD display. 7-4-3.
Page 41
↓ Display: Similarly, when an Up key is pressed, the cursor will move to the upper line as well as scroll the display. If the cursor is on the first line, the program will ignore the Up key. Similarly, if the cursor is on the last line of the menu, the program will ignore the Down key.
Page 42
7-4-3-2. System Setup The system setup is as follows: Date and Time Setting HDD Setting Type of Drive Drive A and B Boot Sequence and Internal Cache External Cache and System Shadow Setting Parity and Video Shadow Setting Boot ROM Setting —...
Page 43
When the System Setup is selected, the following figure will be displayed and the cursor is placed on the date field on first line. The Left key is used to move the cursor from the date field to the month field and from the month field to the year field.
Page 44
The <Enter> key is used to exit this setup and return to the Main Menu. The options available for drive A are: • 360KB 3.5” • 720KB 3.5” • 1.44M 3.5” • 1.2M 5.25” and • No. 7-4-3-3. Reset to Default Values When this sub-menu is selected, the following figure will be displayed.
Operator display : SA-5001M Monochrome LCD display SA-5002C Color LCD display To mount the color LCD display SA-5002C to SA-5000, the following operation is necessary; 1. Open the upper case. 2. Replace the Video BIOS ROM from Monochrome to Color.
3. Preparation Connect loop back test connector to the I/F terminal on the rear panel. Connect a PC keyboard to Ext.KB which is located on the left side of the SA-5000/5100 and turn the slide switch to “K” position. Connect two cash drawer units.
Page 47
Print Turn the power on. Make sure that BIOS version indi- cation on <screen 1> is 1.3. • SA-5000/5100 display and the CRT change to <screen 2>. • LCD back light turns on. • Make sure that the LCD contrast is proper.
Page 48
Print To be checked Operation NVRAM Test : Page 0 PASSED NVRAM test Display indicates; NVRAM Test : Page 1 PASSED NVRAM Test : Page 0 PASSED NVRAM Test : Page 2 PASSED NVRAM Test : Page 1 PASSED NVRAM Test : Page 3 PASSED NVRAM Test : Page 2 PASSED NVRAM Test : Page 4 PASSED NVRAM Test : Page 3 PASSED...
Page 49
MCR test Read the card while display A:\987654321098765432109876543210987654321098765432 indicates; 1098765432109876543210987654 A : \ > Bad command or file name A:\>198506050055555 [T][S][T][9][5][5][ENTER] for SA-5000 Display indicates; <SA-5100> [T][S][T][9][5][6][ENTER] for SA-5100 A : \ > cycle • • 1014545890101454589010145458901014545890101456458 A : \ > pause 1014545890101454589010145458901014545890101456458 Press any key to continue..
Page 50
Print Operation To be checked <SA-5000> A : \ > pause !”#$%’O*+,-./0123456789:;<=>?@ABCDEFG Press any key to continue..HIJKLMNOPQRSTUVWXYZ[\] abcdefghijklmno [ENTER] pqrstuvwxyz{|} BBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBB A : \ > dskbench BBBBBBBBBBBBBBBBBBBBBBBBBBBBB DISK Drive Speed TEST v0.03 Copyright BBBBBBBBBBBBBBBBBBBBBBBBBBBBB 1992 ZOBplus Hayami 500 Kbyte file Write &...
Page 51
<Screen 1> American Megatrends AMIBIOS(C) 1996 American Megatrends Inc., Version 1.3 3712KB OK WAIT... Auto-Detecting Pri Master..IDE Hard Disk Auto-Detecting Pri Slave...Not Detected Pri Master 02.02.01. ST3850A (C)American Megatrends Inc., 41-1000-000000100111111-071595-FINAL-F <Screen 2> AMIBIOS System Configuration(C) 1985-1996, American Megatrends Inc., Main Processor : Am5x86(X5)-P75 Base Memory Size...
10.TROUBLE SHOOTING Problem Solution System does not respond Check that the system is properly Connected to the power source Check if the power supply is still working. If the power supply is not working ( most basic approach is to feel the fan from the air vent ), do a thorough check to determine the cause.
Page 93
R14A R14B AC L +12 V DC+12V AC N +5 V DC+5V R12A R12B DC-5V –5 V R10 L3 DC-12V –12 V +24 V DC+24V DC+24V VR51 Name: Board No. Drawing No. POWER SUPPLY UNIT KCM150-51C — 91 —...