TFT-LCD TV/MONITOR Chassis Model RE23EO LE23R51B RE26EO LE26R51B RE32EO LE32R51B RE40EO LE40R51B SERVICE Manual TFT-LCD TV/MONITOR CONTENTS 1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List 7. Parts List 8.
Page 2
Samsung Electronics Co.,Ltd. h This Service Manual is a property of 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Gyeonggi-Do, Samsung Electronics Co., Ltd. Korea, 443-742 Any unauthorized use of Manual can be Printed in Korea punished under applicable International P/N : BN82-00128A-00 and/or domestic law.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
4 Alignments and Adjustments 4 Alignments and Adjustments 4-1 General Alignment Instuction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
4 Alignments and Adjustments 4-2 Factory Mode Adjustments 4-2-1 Entering Factory Mode 1. To enter “Service Mode” Press the remote -control keys in this sequence : - If you do not have Factory remote - control I N FO MENU MU TE - If you have Factory remote - control - The buttons are active in the service mode.
Page 11
4 Alignments and Adjustments 4-3-1 White Balance - Calibration 4-3-2 White Balance - Adjustment...
Page 12
4 Alignments and Adjustments 4-3-3 Conditions for Measurement 1. On the basis of toshiba ABL pattern : High Light level (57 IRE) - INPUT SIGNAL GENERATOR : MSPG-925LTH * Mode NO 1 : 744X484@60 Hz 6 : 1280X720@60 Hz NO 21 : 1024X768@60 Hz * Pattern NO 36 : 16 Color Pattern NO 16 : Toshiba ABL Pattern 2.
Page 13
4 Alignments and Adjustments c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode) - Adjust sub - Brightness to set the 'Y' value. - Adjust red offset ('x') and blue offset ('y') to the color coordinates. * Do not adjust green offset data.
Page 14
4 Alignments and Adjustments 4-4 Flash ROM Update 1. Installthe Flash Downloader ConnectSet(Service Jack)and Jig Cable to execute Program Update. 2. Flash Downloader program update -Before Turning on the set,Click "connect"which is under of OSD Screen! -Turn on the Set. 3.Open the New Update File and Click the Program and Verify.
3 Disassembly and Reassembly 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LE23A41B/LE26A41B/LE32A41B LCD TV. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 LE23R51B Disassembly Cautions: 1.
Page 18
3 Disassembly and Reassembly 6. Remove 9 screws and Lift up the shield panel and remove 4 screws. 7. Lift up the shield cover and LCD panel. 3-2 LE26R51B, LE32R51B Disassembly 1. Place LCD TV face down on cushioned table. Remove 14 screws from the rear cover.
Page 19
3 Disassembly and Reassembly 4. Remove 11 screws from the shield.and lift up the shield. 5. Remove 5 screws(Left :2/Right :3) 6. Lift up the BRKT. 3-3 LE40R51B Disassembly 1. Remove 8 screws from rearcover. Remove 4 screws from grip on the stand. 2.
Page 20
3 Disassembly and Reassembly 3. Disconnect speaker cable, function cable and Remove screws from the shield. 4. Disconnect Power Cables, LVDS Cable from the power board. 5. Remove 4screws from the Main board and lift up the board. 6. Remove 4 screws from the power board. Disconnect Cables.
Page 21
3 Disassembly and Reassembly 7. Disconnect inverter cable. Lift up the power board. 8. Remove screws. 9. Remove screws from the panel BRKT. Remove screws from the cabinet BRKT and lift up the panel Assy. 10. Lift up the panel, Remove screws from the panel BRKT(R/L).
Page 22
3 Disassembly and Reassembly 3-4 Reassembly Reassembly procedures are in the reverse order of dissasembly procedures.
2 Product Specifications 2-5 Pin Assignments 2-5-1 HDMI Type A pin Singnal Name Wire TMDS Data2+ TMDS Signal wire TMDS Data2 Shield TMDS Shield TMDS Data2- TMDS Signal wire TMDS Data1+ TMDS Signal wire TMDS Data2 Shield TMDS Shield TMDS Data1- TMDS Signal wire TMDS Data0+ TMDS Signal wire...
Page 30
2 Product Specifications 2-5-2 Component 1 2-5-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L RCA White Audio R RCA Red 2-5-4 A/V RCA Yellow CVBS Audio L RCA White Audio R RCA Red...
Page 31
2 Product Specifications 2-5-5 SCART 1 Separate Separate SC1 RED OUT SC1 RED IN SC1 LEFT OUT SC1 RED SC1 LEFT IN SC1 FAST BLANKING SC1 BLUE SC1 SWITCHING SC1 CVBS OUT SC1 CVBS IN SC1 GREEN 2-5-6 SCART 2 Separate Separate SC2 RED OUT...
2 Product Specifications 2-6 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. 2-6-1 LCD Panel Mode1 mode...
5 Troubleshooting 5 Troubleshooting 5-1 No Power LAMP off, power indicator Check a connection a power cable. LED red color? Does proper DC 12V Change a Assy PCB Power. appear at C801, C807? Does proper DC A3.3V, Check a IC812, IC801. A5V appear at Change a main PCB ass'y.
Page 38
Change a main PCB ass'y. DIN(0:23)of IC312? Does the digital data appear at Check a IC201. output of Change a main PCB ass'y. LVDS TX(FT250~253)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 39
5 Troubleshooting WAVEFORMS R,G,B Output Signal of IC906 R,G,B Output Signal of IC312 Digital Output Data of IC201...
Page 40
DIN(0:23), Change a main PCB ass’y. HDMI(Data, Clk +/-)? Does the digital data Check a IC201. appear at output of IC201 Change a main PCB ass'y. LVDS(FX250~253)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 41
5 Troubleshooting WAVEFORMS Digital Output Data of IC201 Signal of HDMI(Data)
Page 42
Check a IC203. #13 of IC203? Change a main PCB ass'y. Does the digital data appear at Check a IC201. output of FT250~FT253 ? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 43
5 Troubleshooting WAVEFORMS Digital Output Data of IC201 Tuner_CVBS Output Signal...
Page 44
Check a IC203. #13 of IC203? Change a main PCB ass'y. Does the digital data appear at Check a IC515. output of FT250~FT253? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 45
5 Troubleshooting WAVEFORMS Digital Output Data of IC515 Tuner_CVBS Output Signal...
Page 46
Dose the signal appear at Check a connection harness. R722, R721 of IC201? Does the digital data appear at Check a IC201. Output of FT250~FT253? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel? 5-10...
Page 47
5 Troubleshooting WAVEFORMS Digital Output Data of IC201 Analog Signal(Y,C) to IC201 5-11...
Page 48
5 Troubleshooting 5-7 No Sound Connect a sound cable. Picture is display, no sound. control a volume. Does the signal appear at Pin 51, 50(CH1_L, R Sound) Check a connection harness and and Pin 57, 58 headphone jack. (CH2_L, R Sound) of IC610 (MSP4410K)? Check the DC 8V Check a IC813.
Page 49
5 Troubleshooting WAVEFORMS The Signal are Inputed to IC610 DC +8V Output WaveForm 5-13...
7 Electrical Parts List 7 Electrical Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 7-1 LE23R51B Main PCB Parts Level Loc. No. Code No. Description Specification Remarks SPZ-LE23R51BX/XEC LTA230W1-L02 ..3 BN94-00629S ASSY PCB MAIN ..4...
11 Schematic Diagrams 11 Schematic Diagrams ’ 11-1 Power_Sound Schematic Diagram R,G,B Output Signal of IC312 Signal of HDMI(Data) The Signal are Inputed to IC610 Output WaveForm 11-1...
Page 87
11 Schematic Diagrams ’ 11-3 MICOM Schematic Diagram R,G,B Output Signal of IC906 11-3...
Page 88
11 Schematic Diagrams ’ 11-4 SVP_EX Schematic Diagram Digital Output Data of IC201 Tuner_CVBS Output Signal Analog Signal(Y,C) to IC201 11-4...
Page 89
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-5 LCD23VFAX Schematic Diagram(23") H O T CO LD 250V C 838 222K JP801 V1 : C801, C 802 => 250V/3 30uF VF : C801 => 450/ 120uF, C 802 =>...
Page 90
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-6 INVERTER Schematic Diagram(26", 32") 11-6...
Page 91
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-7 MULTI_SMPS Schematic Diagram(26", 32") 11-7...
Page 92
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-8 PFC_CONTROL SMPS Schematic Diagram(26", 32") 11-8...
Page 93
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-9 STAND BY SMPS Schematic Diagram(26", 32") 11-9...
Page 94
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-10 INVERTER Schematic Diagram(40") 11-10...
Page 95
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-11 MULTI_SMPS Schematic Diagram(40") 11-11...
Page 96
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-12 PFC_CONTROL SMPS Schematic Diagram(40") 11-12...
Page 97
11 Schematic Diagrams -This Document can not be used without Samsung s authorization. 11-13 STAND BY SMPS Schematic Diagram(40") 11-13...