Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch CS 200
Summary of Contents for Bosch CS 200
- Page 1 0010005426-001 Solar controller CS 200 Installation instructions for installers...
-
Page 2: Table Of Contents
2 | Table of contents 7.1 Solar system settings..... . . 13 Table of contents 7.2 Settings for transfer systems ....13 7.3 Settings for freshwater systems . -
Page 3: Key To Symbols And Safety Instructions
Key to symbols and safety instructions | 3 General safety instructions Key to symbols and safety instructions These installation instructions are intended for plumbers, heating engineers and electricians. Explanation of symbols ▶ Read the installation instructions (heat sources, modules, etc.) before installation. Warning symbols ▶... -
Page 4: Product Description
▶ Correct any faults immediately. Product Description Product description • The CS 200 must be used in conjunction with the MS 200 to control a Solar heating system, in certain cases an MS 100 may also be combined. • After operating for 90 minutes, the solar controller has a power reserve of at least 8 hours. -
Page 5: Temperature Sensor Characteristics
Installation | 5 Disposal Rated power (excluding 9 mA ▶ Dispose of packaging in an environmentally responsible illumination) manner. BUS interface EMS 2 ▶ When replacing assemblies or components, dispose of the Permitted ambient temp. 0 °C to 50 °C old assemblies or components in an environmentally Protection class responsible manner. -
Page 6: Electrical Connection
6 | Installation ▶ To avoid inductive interference: Make sure all low-voltage cables are routed separately from mains voltage cables (min. clearance 100 mm). ▶ In the case of external inductive interferences (e.g. from photovoltaic systems), use shielded cables (e.g. LIYCY) and earth the shield on one side. -
Page 7: Basic Principles Of Operation
Basic principles of operation | 7 ▶ Remove the solar controller by lifting upward. auto menu info 0010005432-001 Fig. 6 Control elements [1] fav key – Lists the favourites [2] man key – Deactivates the automatic change of the temperature displayed in the standard display 0010005431-002 [3] auto key –... -
Page 8: Operating The Service Menu
8 | Commissioning Operating the service menu ▶ Turn the rotary control knob to highlight Continue and press the rotary control knob. Closing and opening the service menu The Display switches to the previous menu level. The solar controller operates with the modified setting. Opening the service menu ▶... -
Page 9: Overview Of The Commissioning Steps
5.3.1 Commissioning the solar heating system ( Chapter 5.3, page 9) 8. Check and, if necessary, adjust the settings in the service Menu item menu of the CS 200 solar controller and perform Start configuration wizard? configuration ( Chapter 5.4, page 11) Question Answer / setting 9. -
Page 10: Commissioning The Freshwater System
10 | Commissioning Menu item Menu item Question Answer / setting Question Answer / setting Is a solar pump with speed No | PWM | 0-10 V Check before starting the configuration wizard: control installed? • Module installed and address set? Gross collector area 1 •... -
Page 11: Commissioning The Transfer Station
Shutdown / switching off | 11 5.3.3 Commissioning the transfer station System handover ▶ Enter the contact details of the responsible installer in the Menu item Diagnosis menu > Maintenance > Contact address, e.g. Start configuration wizard? company name, phone number and address or e-mail Question Answer / setting address (... - Page 12 12 | Service menu – Speed ctrl. solar pump...2 – Type collector array 1 – Gross collector area 1 – 2 – Climate zone – Type collector array 1 – Reset solar yield – Climate zone – Reset solar optimisation –...
-
Page 13: Solar System Settings
Service menu | 13 – Keep hot Menu item Purpose of the menu Change solar Graphical configuration of the solar Diagnosis configuration system Current solar Graphical representation of the – Function test configuration configured solar system – Enable function tests Solar parameters Settings for the installed solar system –... -
Page 14: Diagnosis
14 | Service menu Diagnosis Menu item Description Active faults All current faults that are present in the system are displayed here according to their severity. Fault history The last 20 faults are displayed here, sorted in order of the time of occurrence. The fault history can be deleted in the Reset menu (... -
Page 15: Reset
▶ Do not discharge DHW unmixed. If a fault cannot be corrected, Bosch's Technical Support department (see back cover). ▶ Ensure a thermal mixing valve is fitted as stated in the UK G3 building regulations. -
Page 16: Environmental Protection And Disposal
12-15 V DC. Environmental protection and disposal Solar module defective Replace the module Environmental protection is a key commitment of the Bosch Table 17 Fault displays with fault code A11 Group. Quality of products, efficiency and environmental protection Fault code - sub-code - [cause or fault description] are equally important objectives for us. - Page 17 Environmental protection and disposal | 17 Batteries must not be disposed together with your household waste. Used batteries must be disposed of in local collection systems. CS 200 6720850722 (2015/06)
- Page 20 Bosch Thermotechnik GmbH Junkersstrasse 20-24 D-73249 Wernau www.bosch-thermotechnology.com...