Page 1
Model:E830 Countertop POS This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. ...
MATTERS NEED ATTENTION ........................17 8 TRANSPORTATION AND STORAGE......................17 9 CUSTOMER SERVICE CENTER ........................17 ......................... 17 OTE ABOUT FTER SALES ERVICE ............................18 RODUCT AINTENANCE ................................... 18 ONTACT This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 2 / 18 ...
LANDI’s prior written consent. Fujian LANDI reserves the right to claim compensation on all direct or indirect loss incurred by the above illegal action. Fujian LANDI shall not be liable for any damages, failures and data loss to device or accessories resulting from improper operation not in accordance with the guidance of this manual.
In no event shall LANDI be liable for any data or revenue loss, or consequential, indirect, punitive, special or incidental damages resulting from any reasons.
1.2 Network compatibility declaration The product: E830 is in conformity with the following harmonized standards or technical rules: ETSI ES 203201 ETSI TR 103000 is designed to interwork with the following European analogue Public Switched Telephone Network (PSTN) networks: ….country list…...
1 Product Introduction 1.1 Unpacking Inspection Please open the box and check carefully if the terminal and accessories were unpacked or damaged due to transportation. E830 is a device with security characteristic. Any disassembly will probably make it work abnormally.
1, Telephone line cord port 2, Extension telephone line port 3, Power socket 4, COM2 port 5, Drawer type SAM card connector 6, COM1 port 7, USB host expansion port 8, Ethernet RJ45 Port This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 7 / 18 ...
EPT-DEV for WINDOWS; Support ANSI C language Power adapter:AC 100V~240V 50~60Hz/0.3A Power Supply Output:9V/1A Working temperature: -30℃~50℃ Environmental Storage temperature:: -20℃~70℃ Characteristics Relative humidity: 5%~90℅, Non-condensing 188mm L×82mm W×65mm H Dimension & Weight 340g This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 8 / 18 ...
2.2 Product Function and Configuration E830 is a Point of Sales (POS) product developed based on the 3rd Gen, payment kernel of LANDI. It is configured with ARM Cortex-A9 Core Security Processor to provide powerful processing capabilities and security features; and its 2.8”LCD delivers excellent customer experience.
************************************************************************************** NOTE Don’t connect the PINPAD to telephone line cord port, or will cause the damage. ************************************************************************************** 2.3.5 COM1/COM2 port Terminal is configured RS232 port. RJ22 PINPAD E830 Port socket RJ22 Power supply 5.0V PINPAD receive send PINPAD send receive...
Press the top of the SAM cards and pull it out slowly. ****************************************************************************************** NOTE When using only one SAM card, it is recommended to insert SAM1 slot (bottom). ****************************************************************************************** 3.2 SIM Card Installation Same procedures as above Chapter 3.1 This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 11 / 18 ...
Place the paper roll onto paper box and pull out the paper over the ripper. Close the printer cover. Please be noted that the carbon layer side of the printer paper should be faced against the the cover. Leave a section of paper out after closing the cover. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 12 / 18 ...
4.2 Power on/off Operation Normal power on: Press <Power> button for about 1s until the terminal displays the figure below: Normal power off: Press <Power> button for 2s until the terminal displays the figure below: This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 13 / 18 ...
The IC card should be horizontally inserted into the card reader with chip side upwards. Make sure the card is completely inside the card reader and prevent the card chip contacts from being damaged or oxidized, otherwise it may cause transaction failure. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 14 / 18 ...
4.5 RF Card Place the RF card right against the sensing area and remove it until card swiping success prompts. The sensing area of E830 is right above the paper cover. 5 Product Maintenance Guide 5.1 Magnetic Card Reader and ICCR Maintenance Do not attempt to clean the magnetic card reader and IC card reader, for this action may result in damage to the terminal, and that cause warranty invalid.
The wireless communication feature requires the support from local telecom operators. To use such function, you should obtain the data-enabled SIM/UIM card from local telecom operators. You can then insert this card into E830 card slot; and power the device on to implement corresponding operations. When the LCD display the signal icon, it represents the network is successfully connected.
Note about After-sales Service Before asking for customer service, please be noted to back up the data in the terminal. We are not responsible for backing up the data received from our customer service. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 17 / 18 ...