Remote Desktop Connection - Hitachi G200 Quick Start

4
Run the Initial Startup Wizard
The following procedure describes how to connect to the SVP using Remote Desktop Connection (RDC).
You can also connect using Storage Device List (refer to the Hardware Installation and Reference Guide).
1. Con gure the PC to use an IP address of
10.0.0.xxx, where xxx = 1-99 or 101-254, and a
subnet mask of 255.255.255.0.
2. Run RDC:
a. Click Start > All Programs > Accessories
> Remote Desktop Connection.
b. At the Remote Desktop Connection window:
• In the Computer eld, enter the SVP IP
address.
• At the bottom, click Show Options. In the
User Name eld, type SVP-PC\SVP.
• Click Connect.
c. At the next screen, enter the password and
click the right arrow icon to connect to the SVP.
If prompted that the identity of the remote
computer cannot be veri ed, click Yes to
continue.
3. In the Remote Desktop Connection window:
a. Click Start > All Programs > Hitachi
Device Manager - Storage Navigator.
b. Right-click Initial Startup and click Run as
administrator.
c. At the bottom of the Initial Startup Tool
window, click Start Setup .
d. When a message about checking the initial
environment appears, click OK.
4. Complete the Initial Startup elds.
5
Run the Initial Setup Wizard
NOTE
1. Repeat step 2 above to run RDC.
2. In the Remote Desktop Connection
window, click Start > All
Programs > Hitachi Device
Manager - Storage Navigator >
StorageDeviceList.
3. In the Storage Device List window,
double-click the icon of the
registered storage system.
4. Log in to Device Manager - Storage
Navigator.
5. If prompted about a security
certi cate, select Continue to this
website.
6. In the left pane, under Menu, click
Initial Setup Wizard.
7. At the rst screen, enter the storage
system name, contact, and location.
Click Apply and Next.
8. At the next screen, con gure the
system date and time.
9. Click Apply.
10. Set the SVP date, time, and time zone to the local
time using the Windows Control Panel.
Initial Startup Tool
Initial Startup
If you will use advanced Hitachi software applications, refer to the control memory section in the
Hardware Installation and Reference Guide to see whether additional control memory must be installed.
Maintenance Utility
Storage System
S/N: 410006
CTL1
Information
Hardware
Administration
Firmware
Alert Notifications
Licenses
Network Settings
D & Time
Audit Log Settings
Menu
Initial Setup Wizard
Power Management
System Management
NOTE
Default Account (maintenance)
New Password
Re-enter New Password
Network Setting
IPv4 Configuration:
Storage System Address
CTL1:
CTL2:
Subnet Mask:
Default Gateway:
DNS Server 1:
DNS Server 2:
DNS Server 3:
IPv6 Configuration: Enable Disable
5. Click Apply.
6. When Initial Startup is complete, click Close, and then click Confirm.
The SVP reboots automatically. Rebooting takes 5 to 10 minutes.
7. If you did not connect your IP network (switch) to the LAN1 port on
the SVP, do so now.
S/N: 400001
Set up System Information
Storage System
Storage System
Name
Contact 03-xxxx-xxxx
Location Tokyo xxxx
Storage System
HM800M
Type
Serial Number
400001
Data Spare
Number of Drives 74 8
Chassis
Drives Alerts
Install Remove Locate LED
Controller Chassis
DB-00
After running the Initial Setup wizard, you can remove the cables from
SVP ports LAN3 and LAN4, and connect the cables to customer-
NOTE
supplied switches on the network. For more information, see the
Service Processor Technical Reference (FE-94HM8036).
Some parameters must be obtained from the customer
before performing the Initial Startup Wizard and initial setup.
SVP Address
Alert System Locked Logged in as
Last Updated : 2015/02/23 20:32
IPv4 Address CTL1 10.0.0.16
CTL2 10.0.0.17
IPv6 Address CTL1
CTL2
Temperature 25 degree C
Free Total
9 91
Apply Cancel
Logout ?
user 00
Graphic Table
Go to Detail
Go to Detail