Configuration of the receiver _______________________ 12 8.1 Basic configuration _______________________________________12 8.2 Advanced configuration ___________________________________13 Erasing all transmitters in the receiver ________________________13 Description of Sesam 800 K3 transmitter _____________ 14 Indications on the transmitter _______________________________14 Using the system _________________________________ 15 Configuration of the transmitter _____________________ 15 11.1 Group ID _______________________________________________15 Replacing batteries in the transmitters _______________ 17 12.1 Replacing batteries in Sesam K3 ____________________________17...
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY ÅKERSTRÖMS BJÖRBO CORPORATION COULD VOID THE USER`S AUTHORITY TO OPERATE THE EQUIPMENT. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
The Sesam remote control system is recommended for the remote opera- tion of door opening equipment only. This unit is not intended for use on material handling, people moving or any other critical application. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0...
Page 5
THE RECEIVER UNIT MUST NOT BE INSTALLED OR OPERATED IN EXPLOSIVE ENVIRONMENTS UNLESS APPROPRIATE SECONDARY ENCLOSURE MEASURES ARE TAKEN. WARNING: THE UNIT MUST BE WIRED TO THE CORRECT VOLTAGE; FAILURE TO DO SO MAY DAMAGE THE SYSTEM. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
11. Contents of the manual may be amended by the manufacturer without notice. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
Description of Sesam 800 RX DIN receiver Figure 1. Sesam 800 RX DIN model connections and buttons 1. Learn/Erase button 2. Power connection, 3. Connection to relay 1 4. Connection to relay 2 5. Connection to relay 3 6. LED 5 Squelch LED 6 Status LED 7 Learn Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
(see 2 in fig. 2) will lock the receiver to the rail automatically. Make sure it re- ally snap securely. To remove, withdraw the snap fit and lift the receiver off the rail. Figure 2. DIN receiver, the lock for the rail. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
LED 7 on the receiver flashes 3 times if the Learn procedure is successful. Mount the receiver cover by match top and bottom together and press, the snap fits on the sides locks. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0...
Press the Learn/Erase button for 5 seconds (until LED 7 is OFF). All trans- mitters are now erased from the receiver memory. Mount the lid on the receiver. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
Description of Sesam 800 K3 transmitter 13 (16) Description of Sesam 800 K3 transmitter Figure 4. The Sesam 800 K3 transmitter indicators and buttons 1. Status LED 2. Buttons 1..3 Indications on the transmitter Normal operation Quick flashing RED = Sending message. Continuous GREEN = Relay activated in the receiver (Feedback information from receiver).
Insert the new batteries (see fig. 6 and 7). Close the cover. Tighten the 3 screws with PH00 (torque 0,14 Nm). Figure 5. Battery cover Figure 6. Insert the batteries in the transmitter Figure 7. Batteries in its correct position Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...
Memory card copy to verify error Internal errors. The unit needs service Line power unstable Table 2. Error codes Sesam 800 RX DIN Measure for Sesam 800 RX DIN 92 mm Figure 8. The RX DIN receiver measure. Sesam 800 K3 RXDIN USA Manual Document-ID: 946415-000 Version: A0 Author: SH...