1. PRODUCT DESCRIPTION Erbium-doped fiber amplifier (EDFA) has advantages of low noise, high gain, wide bandwidth, efficient pump and stable working condition etc. It is used in CATV system widely. As the transmitting nodes in the CATV system increase constantly, fiber to the home (FTTH) and fiber to the building (FTTB) are popular.
operating parameters. 2.4 Network Type Select All-piece status monitoring transponder guarantees to meet the national standard and be compatible with the SCTE HMS standard, it enables network management to monitor capabilities. 2.5 Power Supply Double hot pluggable power supply: switching power supply is pluggable type with aluminum profile structural, it helps greatly to cooling and replacement.
4.2 Block Diagram of Integrated WDM WD 1543 WD 1543 15 50n m 131 0nm 149 0nm 4.3 Front/Back Panel Drawing 5. TECHNICAL PARAMETERS 5.1 Technical Parameters Item Unit Technical Parameter Remark Operating bandwidth 1540- 1565 Suggested optical input power Optical input power range -5- +10 0 - +3dBm...
Page 6
Saturated output power 27~33 RS232 communication Power supply 115~265 Power supply Consumption <30 Operating temperature range °C 0~50 Max. operating relative humidity Max 95% no condensation Storage Temperature Range °C -20 ~ +85 Dimension 40.5(W) x 245.8(D) x 360(H) PON optical path with WDM PON port operating wavelength 1310/1490 PON port insertion loss...
EDFA-1550-8×22-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×23-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×17-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×18-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×19-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×20-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×21-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×22-HP-1U FC/APC or SC/APC or E2000 EDFA-1550-8×23-HP-1U...
Page 8
of pump laser. As shown in Figure (2) 6.8.1 Pump Switch State: If there is no light power input, pump will keep close. Figure (2)7.1. 6.8.2 Lead Pump Bias: Figure (2) 7.2, displaying LD bias currents in laser. When the operating current is greater than 130% of rated current, the working life of laser are affected, even damage the lasers.
Page 9
6.8.7 Back to Previous Menu: Figure (2) 7.7. In the current page click the button " " to back to previous menu. 6.9 Power Parameter: Figure (1).In the current page click the button " " to inquire the power parameters, as shown in Figure (5). The display circuit of supply voltage (+24V,+12V,+5V,-5V): display real-time values of current power supply.
master with another is spare, the master is open and the spare is on standby. If the two are linking, the power-on indication will be open. ③ When RS232 is normal and a machine is master with another is spare, if the master is close, the spare will be open, when the master open again, the spare will be on standby, the same as working on spare.
Page 11
users and manufacturers. Imported equipment is generally claimed with a network management system which is based on industry standard RS232 or RJ45 interface. In order to achieve the network management, the users need to purchase high-cost private network management software. And each manufacturer's software is not compatible with each other.
7.2 Search Interface of the Equipment 8. NOTES ABOUT OPTICAL CONNECTION 8.1 Please Carefully Clear All The Fiber Optic Connectors And Connectors Before Connection. Cleaning Guide: 8.1.1 Fiber Optical Jumper Removal the dust cap of fiber optic connector, pay attention to confirm the ...
and clean the other side of the optical fiber jumper connector directly ; Kindly Note: When handling fiber optic connectors must be very careful to avoid damage. 8.1.2 Using the optical fiber jumper to connect the output of optical transmitter to the optical power meter; 8.1.3 Using the optical power meter to check the output of the transmitter optical power is within normal limits.
Page 14
In the warranty period, users have the right to repair or replace the defective product confirmed by the company. However, the above provision is considered invalidly to change ownership, or the irregularities caused by use, storage, transport, assembly or accidents. 10.2 Assurance for Specific Product and Guide to Repair All products are produced according to high-quality standards to ensure that avoid the failures in technology, materials and external framework, etc.