Page 1 Grid Solutions Feeder Protection System Instruction Manual Product version: 7.6x GE publication code: 1601-0093-AF1 (GEK-130999) E83849 LISTED IND.CONT. EQ. 52TL 1601-0093-AF1...
Page 2 The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice.
Page 3: Table Of Contents
Type tests ..........................2-38 2.5.14 Production tests ........................2-38 2.5.15 Approvals ..........................2-39 2.5.16 Maintenance.........................2-39 3 INSTALLATION Unpack and inspect ....................3-1 Panel cutouts ......................3-2 3.2.1 Horizontal units ........................3-2 3.2.2 Vertical units ........................... 3-5 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 4 3.7.5 Automatic discovery of UR devices................3-65 Connect to the F60 ....................3-66 3.8.1 Connect to the F60 in EnerVista.................. 3-66 3.8.2 Use Quick Connect via the front panel RS232 port..........3-67 3.8.3 Use Quick Connect via a rear Ethernet port............3-68 Set up CyberSentry and change default password........3-69...
Page 5 Direct inputs and outputs....................5-136 5.3.19 Teleprotection ........................5-142 5.3.20 Installation ..........................5-143 Remote resources ....................5-143 5.4.1 Remote resources configuration ................5-143 System setup.......................5-145 5.5.1 AC inputs ..........................5-145 5.5.2 Power system........................5-146 5.5.3 Signal sources........................5-147 5.5.4 Breakers..........................5-150 5.5.5 Disconnect switch control...................5-155 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 6 5.12 Testing ......................... 5-357 5.12.1 Test mode function ......................5-357 5.12.2 Test mode forcing......................5-358 5.12.3 Phasor Measurement Unit test values..............5-358 5.12.4 Force contact inputs ..................... 5-359 5.12.5 Force contact outputs ....................5-360 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 7 6.5.2 Event records ........................6-27 6.5.3 Oscillography........................6-29 6.5.4 Data logger ...........................6-29 6.5.5 Phasor Measurement Unit records................6-30 6.5.6 Breaker maintenance.......................6-30 6.5.7 Hi-Z records ..........................6-31 Product information .................... 6-31 6.6.1 Model information......................6-31 6.6.2 Firmware revisions ......................6-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 8 10.7 Back up and restore settings ................10-8 10.7.1 Back up settings .........................10-8 10.7.2 Restore settings ....................... 10-11 10.8 Upgrade software....................10-13 10.9 Upgrade firmware ..................... 10-13 10.10 Replace front panel ................... 10-15 10.11 Replace module ....................10-23 viii F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 9 A FLEXANALOG FlexAnalog items ....................A-1 OPERANDS B RADIUS SERVER RADIUS server configuration ................B-1 CONFIGURATION C COMMAND LINE Command line interface ..................C-1 INTERFACE D MISCELLANEOUS Warranty .........................D-1 Revision history ......................D-1 ABBREVIATIONS INDEX F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 10 TABLE OF CONTENTS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 11: Introduction
Ensure that the control power applied to the device, the alternating current (AC), and voltage input match the ratings specified on the relay nameplate. Do not apply current or voltage in excess of the specified limits. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 12: For Further Assistance
Website: http://www.gegridsolutions.com/multilin When contacting GE by e-mail, optionally include a device information file, which is generated in the EnerVista software by clicking the Service Report button. When using the optional graphical front panel, the report instead can be generated by connecting a USB drive to the front panel.
Page 13 CHAPTER 1: INTRODUCTION FOR FURTHER ASSISTANCE Figure 1-1: Generate service report in EnerVista software F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 14 FOR FURTHER ASSISTANCE CHAPTER 1: INTRODUCTION F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 15: Product Description
This chapter outlines the product, order codes, and specifications. 2.1 Product description The F60 Feeder Protection System is part of the Universal Relay (UR) series of products. It is a microprocessor-based relay for feeder protection. Overvoltage and undervoltage protection, overfrequency and underfrequency protection, breaker failure protection, directional current supervision, fault diagnostics, remote terminal unit (RTU), and programmable logic functions are provided.
Page 16: Description
PRODUCT DESCRIPTION CHAPTER 2: PRODUCT DESCRIPTION The F60 uses flash memory technology that allows field upgrading as new features are added. Firmware and software are upgradable. The following single-line diagram illustrates the relay functionality using American National Standards Institute (ANSI) device numbers.
Page 17: Security
The F60 supports password entry from a local or remote connection. Local access is defined as any access to settings or commands via the front panel interface. This includes both keypad entry and the through the front panel RS232 port.
Page 18 When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the front panel, the local password applies.
Page 19 |---------- Control Elements |---------- Inputs / Outputs |--------------- Contact Inputs |--------------- Contact Input threshold |--------------- Virtual Inputs |--------------- Contact Outputs |--------------- Virtual Outputs |--------------- Resetting |--------------- Direct Inputs |--------------- Direct Outputs |--------------- Teleprotection F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 20 In cases where user-attributable access is required especially to facilitate auditable processes for compliance reasons, use RADIUS authentication only. When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication database to authenticate the user. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 21: Order Codes
The order code is on the product label and indicates the product options applicable. The F60 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit. It consists of the following modules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications.
Page 22 Enhanced front panel with Turkish display and user-programmable pushbuttons Enhanced front panel with German display Enhanced front panel with German display and user-programmable pushbuttons 7" Graphical front panel display in multiple languages with USB front port and user-programmable pushbuttons F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 23 Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels * When an 8Z module is ordered, rear slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 24 ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION Table 2-5: F60 order codes for reduced-size vertical units - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 25 Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels * When an 8Z module is ordered, slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-11...
Page 26: Order Codes With Process Bus Modules
ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION 2.3.2 Order codes with process bus modules Table 2-6: F60 order codes for horizontal units with process bus - * ** - * * * - F ** - H ** - M **...
Page 27 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-13...
Page 28 ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION Table 2-7: F60 order codes for reduced-size vertical units with process bus - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 29: Replacement Modules
Replacement modules can be ordered separately. When ordering a replacement CPU module or front panel, provide the serial number of your existing unit. Not all replacement modules apply to the F60 relay. The modules specified in the order codes for the F60 are available as replacement modules for the F60.
Page 30 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs * When an 8Z module is ordered, rear slot F must have an 8F or 8G module. 2-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 31 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs * When an 8Z module is ordered, rear slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-17...
Page 32: Signal Processing
The UR samples its AC signals at 64 samples per cycle, that is, at 3840 Hz in 60 Hz systems, and 3200 Hz in 50 Hz systems. The sampling rate is dynamically adjusted to the actual system frequency by an accurate and fast frequency tracking system. The A/D converter has the following ranges of AC signals: 2-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 33 Measured analog values and binary signals can be captured in COMTRADE format with sampling rates from 8 to 64 samples per power cycle. Analog values can be captured with Data Logger, allowing much slower rates extended over long period of time. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-19...
Page 34: Specifications
> 2.0 × CT: ±1.5% of reading > 2.0 × CT rating Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I t; FlexCurves™ (programmable); Definite Time (0.01 s base curve) Curve multiplier: Time Dial = 0.00 to 600.00 in steps of 0.01...
Page 35 0.1 to 2.0 x CT rating ±1.5% of reading > 2.0 x CT rating Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I t; FlexCurves™ (programmable); Definite Time (0.01 s base...
Page 36 <30 ms at 0.9 pickup at 60 Hz for Definite Time mode AUXILIARY UNDERVOLTAGE Pickup level: 0.004 to 3.000 pu in steps of 0.001 Dropout level: 102 to 103% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V 2-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 37 Typical times are average operate times including variables such as frequency change instance, test method, and so on, and can vary by ±0.5 cycles. OVERFREQUENCY Pickup level: 20.00 to 65.00 Hz in steps of 0.01 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-23...
Page 38 ±3% of operate time or ±42 ms, whichever is greater Operate time: <42 ms at 1.10 × pickup at 60 Hz BREAKER RESTRIKE Principle: detection of high-frequency overcurrent condition ¼ cycle after breaker opens 2-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 39 ±500 ms or 2%, whichever is greater for I < 0.9 × k × I and I / (k × I ) > 1.1 TRIP BUS (TRIP WITHOUT FLEXLOGIC) Number of elements: Number of inputs: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-25...
Page 40: User-Programmable Elements
LEDs on Test sequence 2: all LEDs off, one LED at a time on for 1 s Test sequence 3: all LEDs on, one LED at a time off for 1 s 2-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 41: Monitoring
Data storage: in non-volatile memory DATA LOGGER Number of channels: 1 to 16 Parameters: any available analog actual value Sampling rate: 15 to 3600000 ms in steps of 1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-27...
Page 42: Metering
±1.0% of reading at –1.0 ≤ PF < –0.8 and 0.8 < PF ≤ 10 REACTIVE POWER (VARS) Accuracy at 0.1 to 1.5 x CT rating and 0.8 to 1.2 x VT rating: 2-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 43: Inputs
Standard CT: 0.02 to 46 × CT rating RMS symmetrical Sensitive Ground CT module: 0.002 to 4.6 × CT rating RMS symmetrical HI-Z CT module: 0.002 to 4.6 × CT rating RMS symmetrical F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-29...
Page 44 5 mA Range: –50 to +250°C Accuracy: ±2°C Isolation: 36 V pk-pk IRIG-B INPUT IRIG formats accepted: B000…B007, B120…B127 IRIG control bits: IEEE Std C37.118.1-2011 Amplitude modulation: 1 to 10 V pk-pk 2-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 45: Power Supply
= 45 W/VA contact factory for exact order code consumption INTERNAL FUSE Ratings: Low range power supply: 8 A / 250 V High range power supply: 4 A / 250 V Interrupting capacity: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-31...
Page 46: Outputs
Break (DC inductive, L/R = 40 ms): Voltage Current 24 V 48 V 0.5 A 125 V 0.3 A 250 V 0.2 A Operate time: < 8 ms Contact material: silver alloy 2-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 47 ±0.75% of full-scale for 0 to 1 mA range ±0.5% of full-scale for –1 to 1 mA range ±0.75% of full-scale for 0 to 20 mA range 99% Settling time to a step change: 100 ms Isolation: 1.5 kV F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-33...
Page 48: Communication Protocols
PARALLEL REDUNDANCY PROTOCOL (PRP) (IEC 62439-3 CLAUSE 4, 2012) Ethernet ports used: 2 and 3 Networks supported: 10/100 Mb Ethernet OTHER TFTP, SFTP, HTTP, IEC 60870-5-104, Ethernet Global Data (EGD), IEEE C37.118 2-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 49: Inter-Relay Communications
At extreme temperatures these values deviate based on component tolerance. On average, the output power decreases as the temperature is increased by a factor of 1 dB / 5 °C. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-35...
Page 50: Cybersentry Security
1 phasor metering page for each AC Source 5 tabular metering pages with dynamic metering and status event records page with dynamic update product information page settings, actual values, error messages (targets) 2-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 51: Environmental
95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6 days) OTHER Altitude: 2000 m (maximum) Pollution degree: Overvoltage category: Ingress protection: IP20 front, IP10 back Noise: 0 dB F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-37...
Page 52: Type Tests
Insulation: class 1, Pollution degree: 2, Over voltage cat II 1 Not tested by third party. 2.5.14 Production tests THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. 2-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 53: Approvals
Normally, cleaning is not required. When dust has accumulated on the front panel display, wipe with a dry cloth. To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-39...
Page 54 SPECIFICATIONS CHAPTER 2: PRODUCT DESCRIPTION 2-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 55: Installation
For any issues, contact GE as outlined in the For Further Assistance section in chapter 1. Check that you have the latest copy of the F60 Instruction Manual and the UR Family Communications Guide, for the applicable firmware version, at http://www.gegridsolutions.com/multilin/manuals/index.htm...
Page 56: Panel Cutouts
3.2.1 Horizontal units The F60 is available as a 19-inch rack horizontal mount unit with a removable front panel. The front panel can be specified as either standard or enhanced at the time of ordering. The enhanced front panel contains additional user-programmable pushbuttons and LED indicators.
Page 57 CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-1: Horizontal dimensions (enhanced front panel) Figure 3-2: Horizontal mounting (enhanced and graphical front panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 58 PANEL CUTOUTS CHAPTER 3: INSTALLATION Figure 3-3: Horizontal mounting and dimensions (standard front panel) Figure 3-4: Horizontal dimension (graphical front panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 59: Vertical Units
3.2.2 Vertical units The F60 is available as a reduced size (¾) vertical mount unit, with a removable front panel. The front panel can be specified as either standard or enhanced at the time of ordering. The enhanced front panel contains additional user- programmable pushbuttons and LED indicators.
Page 60 PANEL CUTOUTS CHAPTER 3: INSTALLATION Figure 3-5: Vertical dimensions (enhanced front panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 61 CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-6: Vertical and mounting dimensions (standard front panel) For side-mounting F60 devices with the enhanced front panel, see the following documents available on the UR DVD and the GE Grid Solutions website: • GEK-113180 —...
Page 62 PANEL CUTOUTS CHAPTER 3: INSTALLATION For side-mounting F60 devices with the standard front panel, use the following figures. Figure 3-7: Vertical side-mounting installation (standard front panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 63 CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-8: Vertical side-mounting rear dimensions (standard front panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 64: Rear Terminal Layout
Two-slot wide modules take their slot designation from the first slot position (nearest to CPU module), indicated by an arrow marker on the terminal block. The figure shows an example of rear terminal assignments. 3-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 65 Wire connections to these two modules at 13 inch-pounds. Figure 3-10: CPU modules and power supply The following figure shows the optical connectors for CPU modules. Figure 3-11: LC fiber connector (left) and ST fiber connector (right) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-11...
Page 66: Wiring
WIRING CHAPTER 3: INSTALLATION 3.3 Wiring 3.3.1 Typical wiring Figure 3-12: Typical wiring diagram (T module shown for CPU) 3-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 67: Dielectric Strength
3.3.2 Dielectric strength Dielectric strength is the maximum electric strength that can be sustained without breakdown. It is measured in volts. The table shows the dielectric strength of the UR-series module hardware. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-13...
Page 68: Control Power
The power supply module can be ordered for two possible voltage ranges, and the F60 can be ordered with or without a redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges are as follows (see the Specifications section of chapter 2 for details): •...
Page 69: Ct/Vt Modules
These modules have enhanced diagnostics that can automatically detect CT/VT hardware failure and take the relay out of service. CT connections for both ABC and ACB phase rotations are identical, as shown in the Typical Wiring Diagram. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-15...
Page 70 UR models. Substitute the tilde “~” symbol with the slot position of the module in the following figure. 3-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 71 CT modules must be connected to a ground current source, either a zero-sequence CT (see the Typical wiring diagram with high impedance fault detection earlier in this chapter) or, if a zero-sequence CT is not available, to the neutral conductor of the phase CTs (see diagram below). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-17...
Page 72: Process Bus Modules
3.3.5 Process bus modules The F60 can be ordered with a process bus interface module. The module interfaces with the HardFiber Process Bus System, or HardFiber Brick, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber Bricks.
Page 73: Contact Inputs And Outputs
Form-A contact output with or without a current or voltage monitoring option is not polarity sensitive. The polarity shown in the figure is required for solid-state contact output connection. Figure 3-18: Form-A and solid-state contact outputs with voltage and current monitoring F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-19...
Page 74 Output or Terminal Output or assignment input assignment assignment input assignment input Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A 3-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 75 2 Inputs Form-A Not Used Form-A ~6a, ~6c 2 Inputs Form-A Solid-State ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs Form-A Not Used ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs Form-A Solid-State F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-21...
Page 76 ~5a, ~5c 2 Inputs 2 Outputs Solid-State Solid-State ~6a, ~6c 2 Inputs 2 Outputs Not Used Not Used ~7a, ~7c 2 Inputs 2 Outputs Solid-State Solid-State ~8a, ~8c 2 Inputs Not Used 3-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 77 CHAPTER 3: INSTALLATION WIRING Figure 3-19: Contact input and output module wiring (Sheet 1 of 2) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-23...
Page 78 CHAPTER 3: INSTALLATION Figure 3-20: Contact input and output module wiring (Sheet 2 of 2) For proper functionality, observe the polarity shown in the figures for all contact input and output connections. 3-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 79 F60 input even when the output is open, if there is a substantial distributed capacitance (represented by C1) present in the wiring between the output and the F60 input and the debounce time setting in the F60 relay is low enough.
Page 80 This operation of contact inputs also can be prevented by using the Auto-Burnish contact inputs or contact inputs with active impedance. Figure 3-23: Contact input connected to a contact output with resistor (R2) across the input 3-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 81 Eq. 3-2 The 2 mA current is used in case the contact input is connected across the GE Form A contact output with voltage monitoring. Otherwise use the amperage of the active circuit connected to the contact input when its contact output is open and the voltage across the contact input is third trigger threshold to calculate the resistor value.
Page 82 Consequently, the threshold voltage setting is also defined per group of two contact inputs. The auto-burnish feature can be disabled or enabled using the DIP switches found on each daughter card. There is a DIP switch for each contact, for a total of 16 inputs. 3-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 83 Contact inputs susceptible to parasitic capacitance caused by long cable runs affected by switching surges from external circuits can result in inadvertent activation of contact inputs with the external contact open. In this case, GE recommends using the contact I/O module with active impedance circuit.
Page 84: Transducer Inputs And Outputs
The following figure illustrates the transducer module types (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay. 3-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 85 CHAPTER 3: INSTALLATION WIRING Where a tilde “~” symbol appears, substitute the slot position of the module. Figure 3-27: Transducer input/output module wiring The following figure show how to connect RTDs. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-31...
Page 86: Rs232 Port
EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is shown in the following figure for both 9-pin and 25-pin connectors. The baud rate for this port can be set, with a default of 115200 bps. 3-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 87: Cpu Communication Ports
Figure 3-29: RS232 front panel port connection 3.3.9 CPU communication ports 3.3.9.1 Overview In addition to the front panel RS232 port, there is a rear RS485 communication port. The CPU modules do not require a surge ground connection. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-33...
Page 88 This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the F60 COM terminal (#3); others function correctly only if the common wire is connected to the F60 COM terminal, but insulated from the shield.
Page 89: Irig-B
IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The IRIG-B code allows time accuracies of up to 100 ns. Using the IRIG-B input, the F60 operates an internal oscillator with 1 µs resolution and accuracy.
Page 90: Direct Input And Output Communications
UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to UR4-Rx, and UR4-Tx to UR1-Rx. A maximum of 16 URs can be connected in a single ring. 3-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 91 UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1 for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the second ring. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-37...
Page 92 Those that apply depend on options purchased. The options are outlined in the Inter-Relay Communications section of the Order Code tables in Chapter 2. All of the fiber modules use ST type connectors. 3-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 93: Fiber: Led And Eled Transmitters
The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser modules. Figure 3-38: 7x Laser fiber modules The following figure shows configuration for the 2I and 2J fiber-laser modules. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-39...
Page 94: Interface
The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical arrangement of these pins, see the Rear Terminal Layout section earlier in this chapter. All pin interconnections are to be maintained for a connection to a multiplexer. 3-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 95 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is inserted fully. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-41...
Page 96 (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). The switch settings for the internal and loop timing modes are shown. 3-42 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 97 One source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface. Figure 3-45: G.703 dual loopback mode F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-43...
Page 98: Rs422 Interface
(data module 1) connects to the clock inputs of the UR RS422 interface in the usual way. In 3-44 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 99 Figure 3-48: Timing configuration for RS422 two-channel, three-terminal application Data module 1 provides timing to the F60 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure because they vary by manufacturer.
Page 100: Rs422 And Fiber Interface
For the direct fiber channel, address power budget issues properly. When using a laser interface, attenuators can be necessary to ensure that you do not exceed maximum optical input power to the receiver. Figure 3-50: RS422 and fiber interface connection 3-46 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 101: And Fiber Interface
Connection — as per all fiber optic connections, a Tx to Rx connection is required The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94 standard. The figure shows the concept. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-47...
Page 102 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F60 communication for two and three terminal applications.
Page 103 When the clips have locked into position, the module is inserted fully. Figure 3-55: IEEE C37.94 timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-49...
Page 104: C37.94Sm Interface
Fiber optic cable length — Up to 11.4 km • Fiber optic connector — Type ST • Wavelength — 1300 ±40 nm • Connection — As per all fiber optic connections, a Tx to Rx connection is required 3-50 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 105 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F60 communication for two and three terminal applications.
Page 106 When the clips have locked into position, the module is inserted fully. Figure 3-58: C37.94SM timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. 3-52 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 107: Activate Relay
Press the right arrow until the message displays. MESSAGE SECURITY Press the down arrow until the message displays. MESSAGE INSTALLATION Press the right arrow until the Not Programmed message displays. MESSAGE RELAY SETTINGS: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-53...
Page 108: Install Software
To communicate via the RS232 port, use a standard straight-through serial cable. Connect the DB-9 male end to the relay and the DB-9 or DB-25 female end to the computer COM2 port as described in the CPU Communication Ports section earlier in this chapter. 3-54 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 109: System Requirements
This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the F60 rear communications port. The converter terminals (+, –, GND) are connected to the F60 communication module (+, –, COM) terminals. See the CPU Communication Ports section in chapter 3 for details.
Page 110: Install Software
Click the Next button to begin the installation. The files are installed in the directory indicated, and the installation program automatically creates icons and adds an entry to the Windows start menu. 3-56 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 111: Add Device To Software
3.7 Add device to software You connect remotely to the F60 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup software. The F60 also can be accessed locally with a computer through the front panel RS232 port or the rear Ethernet port using the Quick Connect feature.
Page 112 From the Windows desktop, right-click the My Network Places icon and select Properties to open the network connections window. Or in Windows 7, access the Network and Sharing Center in the Control Panel. Right-click the Local Area Connection icon and select Properties. 3-58 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 113 Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button. Click the “Use the following IP address” box. Enter an IP address with the first three numbers the same as the IP address of the F60 relay and the last number different (in this example, 1.1.1.2).
Page 114 Minimum = 0ms, Maximum = 0ms, Average = 0 ms Pinging 1.1.1.1 with 32 bytes of data: verify the physical connection between the F60 and the computer, and double-check the programmed IP address in setting, then repeat step 2. Product Setup  Communications  Network  IP Address...
Page 115 Click the Quick Connect button to open the window. Select the Ethernet interface and enter the IP address assigned to the F60, then click the Connect button. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick Connect”...
Page 116: Configure Serial Connection
For the RS232 connection, a computer with an RS232 port and a serial cable are required. To use the RS485 port at the back of the relay, a GE Grid Solutions F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.
Page 117: Configure Ethernet Connection
SEL-2032. This option enables display of a terminal window to allow interaction with the other device. 11. Click the Read Order Code button to connect to the F60 and upload the order code to the software. If a communications error occurs, ensure that the EnerVista software serial communications values entered in the previous step correspond to the relay setting values, and also ensure that the same IP address is not assigned to multiple F60 ports.
Page 118 12. If using a gateway to connect to the device, select Yes from the drop-down list. 13. Click the Read Order Code button to connect to the F60 device and upload the order code. If the device was entered already, a message displays "Device ’x’ is also using IP address.." If a communications error occurs, ensure that the values entered in the previous steps correspond to the relay setting values, and also ensure that the same IP address is not assigned to multiple F60 ports.
Page 119: Configure Modem Connection
CHAPTER 3: INSTALLATION ADD DEVICE TO SOFTWARE The device has been configured for Ethernet communications. Proceed to the Connect to the F60 section to begin communications. 3.7.4 Configure modem connection A modem connection allows a computer to communicate with a UR device over phone lines.
Page 120: Connect To The F60
When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the device. When unable to connect, ensure that the same IP address is not assigned to multiple F60 ports, for example under Settings > Product Setup > Communications > Network.
Page 121: Use Quick Connect Via The Front Panel Rs232 Port
Connect a nine-pin to nine-pin RS232 serial cable to the computer and the front panel RS232 port. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista DVD or online from http://www.gegridsolutions.com/multilin). See the software installation section if not already installed.
Page 122: Use Quick Connect Via A Rear Ethernet Port
Connect" and displays them in the Online Window. Expand the sections to view data directly from the F60 device. Use the Device Setup button to change the site name. Each time that the EnerVista software is initialized, click the Quick Connect button to establish direct communications to the F60.
Page 123: Set Up Cybersentry And Change Default Password
IID — Instantiated IED capability description file — Actual settings on UR • CID — Configured IED description file — Settings sent to the UR (may or may not be actual settings) The import is done in the Offline Window area. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-69...
Page 124: Connect To D400 Gateway
3.11 Connect to D400 gateway A GE Multilin D400 Substation Gateway can be used to collect data from UR devices in a local area network (LAN). It collects metering, status, event, and fault report data from serial or LAN-based intelligent substation devices, and it pre-processes the data.
Page 125: Setting Files
These are the configuration/settings files in the IEC 61850 SCL/IID format. The ur.iid file is saved with a "_YYMMDDhhmmss" retrieval time stamp, for example ur_170525183124.iid. It is stored in the D400 folder system using the UR site and device name. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-71...
Page 126 CONNECT TO D400 GATEWAY CHAPTER 3: INSTALLATION 3-72 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 127: Interfaces
The EnerVista UR Setup software is provided with every F60. This chapter outlines the EnerVista software interface features. The EnerVista UR Setup Help File also provides details for getting started and using the software interface.
Page 128: Event Viewing
IP Address IP Subnet Mask IP Routing When a settings file is loaded to a F60 that is in-service, the following sequence occurs: The F60 takes itself out of service. The F60 issues a UNIT NOT PROGRAMMED major self-test error.
Page 129: File Support
Site list / online window area Settings list / offline window area Software windows, with common toolbar Settings file data view windows, with common toolbar Workspace area with data view tabs Status bar 10. Quick action hot links F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 130: Protection Summary Window
4.1.6 Protection summary window The Protection Summary is a graphical user interface to manage elements, such as enabling and disabling them. Access it under Settings > Protection Summary. See the Settings chapter for information on use. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 131: Settings Templates
Settings file templates simplify the configuration and commissioning of multiple relays that protect similar assets. An example is a substation that has 10 similar feeders protected by 10 UR-series F60 relays. In these situations, typically 90% or greater of the settings are identical among devices. The templates allow engineers to configure and test these common settings, then lock them so that they are not available to users.
Page 132 Figure 4-4: Settings template with all settings specified as locked Specify the settings to make viewable by clicking them. A setting available to view is displayed against a yellow background. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 133 To display only the settings available for editing: Select an installed device or a settings file from the left menu of the EnerVista UR Setup window. Apply the template by selecting the Template Mode > View In Template Mode option. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 134 Once the template has been applied, users are limited to edit the settings specified by the template, but all settings are shown. The effect of applying the template to the phase time overcurrent settings is shown as follows. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 135: Secure And Lock Flexlogic Equations
4.1.8.1 Lock FlexLogic equations To lock individual entries of a FlexLogic equation: Right-click the settings file or online device and select the Template Mode > Create Template item to enable the settings template feature. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 136 The effect of applying the template to the FlexLogic entries is shown here. Figure 4-10: Locking FlexLogic entries through settings templates The FlexLogic entries are also shown as locked in the graphical view and on the front panel display. 4-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 137 Right-click the setting file in the offline window area and select the Edit Device Properties item. The window opens. Figure 4-12: Settings file properties window F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-11...
Page 138: Settings File Traceability
When a settings file is transferred to a F60 device, the date, time, and serial number of the F60 are sent back to EnerVista UR Setup and added to the settings file on the local computer. This information can be compared with the F60 actual values at any later date to determine if security has been compromised.
Page 139 4.1.9.2 Online device traceability information The F60 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista online window as shown in the example.
Page 140: Front Panel Interface
The enhanced front panel consists of LED panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional user-programmable pushbuttons. The front panel is hinged to allow access to removable modules inside the chassis. 4-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 141 The standard front panel can be horizontal or vertical. The following figure shows the horizontal front panel. Figure 4-18: Standard horizontal front panel The following figure shows the vertical front panel for relays ordered with the vertical option. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-15...
Page 142 The USB port is the square type B. User-programmable pushbuttons 9 to 16 can be programmed among the 10 pushbuttons on the left and right sides of the display. 4-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 143: Front Panel Display
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel or the LEDs. To view the front panel in EnerVista software: Click Actual Values > Front Panel, then any option. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-17...
Page 144 The footer dynamically labels the Tab, or control, pushbuttons immediately below. Page content displays between the header and footer. The pages are arranged for navigation in a hierarchical structure similar to that used for the enhanced and standard front panels. 4-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 145 Active targets symbol. View error messages by pressing the Menu Tab pushbutton, then accessing the TARGETS menu. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-19...
Page 146 Factory default names are SLD 1, SLD 2, and so on. Pages that have no configured content have a blank Tab pushbutton label, and the Tab pushbutton does nothing. The label for the current page has a blue background. 4-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 147 Single-line diagram example The following example outlines how to create a circuit breaker diagram, then how to close the second circuit breaker. The figure shows six switches, two breakers, feeder, and ground. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-21...
Page 148 Line Diagram Editor. Add the four switches for the top line by clicking the GE switch symbol in the toolbar, then clicking in the window. If the UR device is not online, the software attempts to connect. Double-click to edit properties. Rotate switches SW569 and SW5682 to 270 degrees.
Page 149 Add the two lower switches. Leave rotation at 0 degrees. Add the breakers by clicking the GE breaker symbol in the toolbar, then clicking in the window. Double-click to edit properties, rotating 90 degrees and setting the color to red (open).
Page 150 Load — Opens single-line diagram files, which replaces all five windows with that in the file To save drawings as a separate file, click File > Save As. The file is saved in the .mif format. 4-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 151 Up to 32 static symbols can be used per single-line diagram. To add a symbol, click it in the toolbox, then click in the window. Double-click the symbol to open its properties window to set orientation. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-25...
Page 152 Each breaker and each disconnect can be configured to use the UR-style symbols, IEC symbols, or simple square/slash symbols as shown in the following figure. The symbols assume horizontal symbol orientation, red - closed color, and green - open scheme. With vertical orientation, they are rotated 90 degrees. 4-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 153 (horizontal or vertical), color scheme (red - closed, or red - open), and assigned side button (if any). If the selected breaker or disconnect element F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-27...
Page 154 A question mark displays in a symbol on the graphical front panel when status is bad. The question mark does not rotate with orientation. Figure 4-34: Symbols when status is bad The following figures show the orientation available for the static components. The default position is 0 degrees. 4-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 155 CHAPTER 4: INTERFACES FRONT PANEL INTERFACE Figure 4-35: Single-line diagram static symbol orientation (sheet 1 of 2) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-29...
Page 156 User-programmable pushbuttons 9 to 16 can be programmed among the 10 pushbuttons on the left and right sides of the screen display. They show dynamically and provide a means to perform the same control as a hardware user- programmable pushbutton. 4-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 157 To add a metering component, click the M symbol in the toolbox, then click in the window. Drag it to its final location. Double-click it to open the properties window. The figure shows the properties that can be edited. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-31...
Page 158 Self Reset, so the alarm displays in a solid color. The blue alarm type is Acknowledgeable, so the alarm flashes until it is acknowledged, for example by navigating with the arrow keys and pressing the ENTER button. The alarm then remains blue until the trigger condition is eliminated. 4-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 159 Alarm types of each window can be configured as Self Reset, Latched, or Acknowledgeable. In Self Reset mode, the window lighting follows the state of the configured FlexLogic operand. The self-reset mode alarm sequence conforms to ISA-18.1-1979 (R2004) standard type A 4 5 6. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-33...
Page 160 In Acknowledgeable mode, both Off to On and On to Off state changes in the configured operand cause the background to flash; the window must be acknowledged/reset to cancel flashing. This mode conforms to ISA-18.1-1979 (R2004) standard type R-6. 4-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 161 The last window is not configured and displays blank/grey. In order for the Ethernet and battery alarms to work, the corresponding self-test alarms have been enabled under Settings > Product Setup > User-Programmable Self Tests (not shown). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-35...
Page 162 Five tabular metering pages can be configured, while there can be a phasor page for each configured AC source. They display on the graphical front panel using the Metering Tab pushbutton. The path to the editor is Settings > Product Setup > Graphical Panel > Metering Editor. 4-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 163 Content to display is configured with the cell lines. The content can be actual values, a status indicator, or text. • Actual value — Select from the FlexAnalogs applicable to the F60, where a FlexAnalog is an analog parameter •...
Page 164: Front Panel Navigation Keys
The decimal key initiates and advances to the next character in text edit mode or enters a decimal point. key can be pressed at any time for context-sensitive help messages. HELP 4-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 165 Tab pushbutton — Five pushbuttons under the display. They navigate through the page hierarchy, and on some pages activate other actions. The display footer dynamically labels the page or action that is activated by the tab pushbutton. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-39...
Page 166: Led Indicators
“Enabled” or “Latched.” If a protection element target setting is “Enabled,” then the corresponding event-cause LEDs remain on as long as the operand associated with the element remains asserted. If a 4-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 167 Support for applying a customized label beside every LED is provided. Default labels are shipped in the label package of every F60, together with custom templates. The default labels can be replaced by user-printed labels. User customization of LED operation is of maximum benefit in installations where languages other than English are used to communicate with operators.
Page 168 Default labels for LED panel 2 The default labels are intended to represent the following: • GROUP 1...6 — The illuminated GROUP is the active settings group • BREAKER 1(2) OPEN — The breaker is open 4-42 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 169 TRIP — Indicates that the selected FlexLogic operand serving as a trip output has operated. This indicator latches; initiate the reset command to reset the latch. • ALARM — Indicates that the selected FlexLogic operand serving as an alarm output has operated F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-43...
Page 170: Front Panel Labelling
NEUTRAL/GROUND — LED 14 — Indicates that neutral or ground was involved 4.2.5 Front panel labelling 4.2.5.1 Enhanced front panel The following procedure requires these pre-requisites: • The UR front panel label cutout sheet (GE part number 1006-0047) has been downloaded from http://www.gegridsolutions.com/products/support/ur/URLEDenhanced.doc and printed • Small-bladed knife To create custom LED and pushbuttons labels for the enhanced front panel: Start the EnerVista UR Setup software.
Page 171 LED labels. Use the tool with the printed side containing the GE part number facing the user. The label package shipped with every F60 contains the three default labels, the custom label template sheet, and the label removal tool.
Page 172 Bend the tab at the center of the tool tail as shown. To remove the LED labels from the F60 front panel and insert the custom labels: Use the knife to lift the LED label and slide the label tool underneath. Ensure that the bent tabs are pointing away from the relay.
Page 173 Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown. To remove the user-programmable pushbutton labels from the F60 front panel and insert the custom labels: Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown. Ensure that the bent F60 FEEDER PROTECTION SYSTEM –...
Page 174 Remove the tool and attached user-programmable pushbutton label. Slide the new user-programmable pushbutton label inside the pocket until the text is properly aligned with the 4-48 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 175 To create LED and pushbutton labels for a standard front panel: In the EnerVista software, if the F60 is not already listed in the Offline Window area, add it by right-clicking it and selecting the Add Device to Offline Window option.
Page 176 4.2.5.3 Graphical front panel The F60 includes software for labelling the LEDs and pushbuttons on the graphical front panel and a sticker sheet with pre- printed and blank labels. The pre-printed labels are on the top-left of the template sheet, and the blank labels are on the bottom-right.
Page 177: Menu Navigation
Use the down, right, left, and up arrows to navigate the menu. The up and down arrow keys move within a group of headers, sub-headers, setting values, or actual MESSAGE F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-51...
Page 178 The Page Up and Page Down Tab pushbuttons also navigate through the list. When there is only a single page of options, they jump to the first and last entries. The options displayed depend on order code. 4-52 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 179: Change Settings
This flash message momentarily appears as confirmation of the storing process. Numerical values that contain decimal places are rounded-off if more decimal place digits are entered than specified by the step value. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-53...
Page 180 An example is a confirmation message upon saving settings. This setting specifies how long to display the message. Press the Menu pushbutton to display the main menu. 4-54 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 181 Figure 4-56: Main menu Use the Up or Down pushbutton to select SETTINGS, then press the Right or ENTER pushbutton. Figure 4-57: Settings menu With PRODUCT SETUP selected, press the Right or ENTER pushbutton. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-55...
Page 182 As the FLASH MESSAGE TIME setting accepts a numerical value, a keypad displays. The time is to be changed to 4.0 seconds. 4-56 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 183 The shift key (up arrow on keyboard) is green upon activation, while the keyboard letters switch to upper case. The globe key (shown greyed-out) toggles the keyboard language between English and another display language selected, for example between English and French. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-57...
Page 184: View Actual Values
Each phasor page has a name, which consists of the value of the SOURCE # NAME setting appended with " Phasors." Phasor pages that have no configured CTs or VTs do not have a Tab pushbutton, and phasor pages that have no configured cells cannot be displayed. 4-58 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 185: Breaker Control
4.2.9 Breaker control The F60 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, that can be presented on front panel LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated from the front panel keypad or automatically initiated from a FlexLogic operand.
Page 186: Change Passwords
The information in this section refers to password security. For information on how to set the password for the first time or change CyberSentry passwords, see the previous chapter or the Settings > Product Setup > Security > CyberSentry section in the next chapter. 4-60 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 187 When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the front panel, the local password must be used.
Page 188: Logic Diagrams
By default, when an incorrect Command or Setting password has been entered via the front panel three times within five minutes, the FlexLogic operand is set to “On” and the F60 does not allow settings or command level LOCAL ACCESS DENIED access via the front panel for five minutes.
Page 189: Flexlogic Design Using Engineer
Works with all UR firmware versions The figure shows an example where several inputs are used to trigger an output. With the OR function, any one of the inputs can trigger the output. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-63...
Page 190 This section explains how to use Engineer. It outlines the following topics: • Design logic • Send file to and from device • Monitor logic • View front panel • Generate connectivity report • Preferences 4-64 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 191: Design Logic
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, virtual outputs 3 and 4 are named DLTrigger Top logic — Seven-minute timer trigger Bottom logic — Turn on LED 9 for 10 seconds when the trigger starts F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-65...
Page 192 This procedure uses input / output logic as an example. To create a logic diagram: In the Offline Window area, access Engineer for the device, then Logic Designer. If the device is not listed, right-click 4-66 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 193 Add the input blocks to the logic diagram. For example, click the I/O Tokens tab on the right, click the Input element, then click in the logic sheet to add it. Or drag-and-drop it. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-67...
Page 194 Line option. The cursor needs to be at the connection point to end the line, not elsewhere on the block. Note that the outline color is no longer red on the blocks. 4-68 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 195 The warning "input using disabled feature" means that input needs to be enabled. Double-click the block, click the View Associated Screen button, enable the setting, save, and recompile. The output and messages are explained in the next section. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-69...
Page 196 IEC 61850 panel and thereby become synchronized. The CID file and the IID file (depending on the preference 'Do not update IID file when updating SCL files') are updated. If the CID file is not already there, it is generated. 4-70 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 197 FLEXLOGIC DESIGN USING ENGINEER The location of these files is C:\ProgramData\GE Power Management\urpc, for example, in the Offline and Online folders. Any FlexLogic equations entered in the Offline Window area are erased. The logic drawn in the Logic Designer window in Engineer in the Offline Window area remain.
Page 198 Click the Ok button to save and exit from the window. In the logic diagram, select an element, then click in the drawing area to add it, click again to add a second box, and so on. 4-72 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 199 Optimization Summary. Changes also display when the FlexLogic Equation Editor is accessed. The logic diagram does not change. In the example shown, no lines were saved to free up space. Figure 4-81: Code optimization results F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-73...
Page 200 Type in the second text string box, or select any of the 32 previous searches from the drop-down list. Click the Search button. Any results display. The search applies to all tabs, not just the active tab. Double-click a search result to view the item. 4-74 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 201: Send File To And From Device
When a window opens, select the device to which you want to send the file, then click the Send button and confirm. The order codes must match. The file is sent to the live device. Any errors can be viewed in the log file at the prompt. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-75...
Page 202: Monitor Logic
(green box outline). In this case, the battery is weak and needs to be replaced. This can be viewed as the Replace Battery message on the front panel of the device and in the EnerVista software under Actual Values > Front Panel > Front Panel or Display/Keypad. 4-76 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 203: View Front Panel And Print Labels
To save the report and labels, click File > Save As, enter a file name, and select the FPR, JPG, or PDF format. Use the instructions in the second tab of the window to add the labels to the physical device. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-77...
Page 204: Generate Connectivity Report
View > Toolbar > Advanced Actions — Active when in Logic Designer. Toggles a toolbar to nudge, rotate, flip, or change the order of an element. View > Show Unused Pins — Enable to display unconnected pins. Disable to eliminate unconnected pins from the view, for example when printing. 4-78 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 205 File Information The text entered here displays at the bottom right of a diagram when printing, provided that the Show Title Block option is enabled. Note the option to change the logo from the GE logo to your company logo. Display The panel sets how the element boxes display.
Page 206 The software displays the color specified when an element is on. There is no color when the element is off. The software displays another color when the status cannot be determined and is unknown. 4-80 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 207 Options display for filtering, such as recording timing for Virtual Inputs and Outputs, but not Communications Status. 4.4.6.4 COMTRADE waveforms Waveform files are viewable in the EnerVista software. The preferences are unrelated to Engineer and are outlined in the UR Family Communications Guide. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-81...
Page 208: Toolbars
When you re-launch the EnerVista software, communication is on by default. 4.4.7.2 Token Toolbox Drawing Tools Draw a line. Click and drag to draw. Draw multiple joined lines. Click and drag for each line. Double-click to finish. 4-82 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 209 Remote inputs from other devices Input from another UR device. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-83...
Page 210 Tag-In can is used to reference an existing Tag-Out. It joins another diagram to a previous diagram. Boolean Tokens These symbols are used to create FlexLogic Equations. Use them as intermediate logic for the Virtual Output equations. The display can vary from that shown here. 4-84 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 211 Place a positive one shot and a negative one shot symbol in the Logic Designer diagram Place a timer in the Logic Designer diagram Elements These blocks configure properties of the element or use element operands as input to FlexLogic equations. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-85...
Page 212 Set the width of the selected components to the same width as the reference component Same Height Set the height of the selected components to the same height as the reference component 4-86 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 213 Front, Back Moves current components to the absolute front or back of all viewable layers Forward, Backward Moves current components on layer higher or lower than its original layer hierarchy F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-87...
Page 214 FLEXLOGIC DESIGN USING ENGINEER CHAPTER 4: INTERFACES 4-88 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 215: Settings
  REAL TIME See page 5-109   CLOCK  FAULT REPORTS See page 5-113    OSCILLOGRAPHY See page 5-115    DATA LOGGER See page 5-117   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 216 See page 5-207    NON-VOLATILE See page 5-212    LATCHES  SETTINGS  SETTING GROUP 1 See page 5-213   GROUPED ELEMENTS   SETTING GROUP 2    F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 217    VIRTUAL OUTPUTS See page 5-345    RESETTING See page 5-345    DIRECT INPUTS See page 5-346    DIRECT OUTPUTS See page 5-346   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 218: Overview
For example, if CT1 = 300 / 5 A and CT2 = 100 / 1 A, then in order to sum these, CT2 is scaled to the CT1 ratio. In this case, the base quantity is 300 A primary, 5 A secondary for CT1, and 300/(100/1) = 3 A secondary for CT2. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 219 Not every operand of a given element in a UR relay generates events, only the major output operands. Elements, asserting output per phase, log operating phase output only, without asserting the common three-phase operand event. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 220: Introduction To Ac Sources
For example, in the scheme shown in the preceding figure, the user configures one source to be the sum of CT1 and CT2 and can name this source as “Wdg1 I.” F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 221: Product Setup
(as described earlier) as follows for a maximum configuration: F1, F5, M1, M5, U1, and U5. 5.3 Product setup 5.3.1 Security 5.3.1.1 Security overview The following security features are available: • Password security — Basic security present by default F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 222 To reset the unit after a lost password: Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email account. Customer service provides a code to reset the relay to the factory defaults.
Page 223 When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the front panel, the local password must be used.
Page 224 When an original password has already been used, enter it in the Enter Password field and click the Send Password to Device button. Re-enter the password in the Confirm Password field. 5-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 225 INVALID ATTEMPTS BEFORE LOCKOUT The F60 provides a means to raise an alarm upon failed password entry. If password verification fails while accessing a password-protected level of the relay (either settings or commands), the FlexLogic operand is UNAUTHORIZED ACCESS asserted.
Page 226 ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout is restarted. The status of this timer updates every five seconds. 5-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 227 It is disabled by default to allow access to the device immediately after installation. When security is disabled, all users have administrator access. GE recommends enabling the EnerVista security before placing the device in service. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 228 If you force password entry by using this feature, ensure that you know the Administrator password. If you do not know the password and are locked out of the software, contact GE Grid Solutions for the default password of a UR device.
Page 229 The EnerVista security management system must be enabled (the Enable Security check box enabled) To modify user privileges: Select the Security > User Management item from the top menu to open the user management window. Locate the username in the User field. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-15...
Page 230 This feature requires a CyberSentry software option. See the Order Codes section in chapter 2 for details. The EnerVista software provides the means to configure and authenticate the F60 access using either a server or the device. Access to functions depends on user role.
Page 231 When the "Device" button is selected, the F60 uses its local authentication database and not the RADIUS server to authenticate the user. In this case, it uses built-in roles (Administrator, Engineer, Supervisor, Operator, Observer, or Administrator and Supervisor when Device Authentication is disabled), as login accounts and the associated passwords are stored on the F60 device.
Page 232 Figure 5-3: Security panel when CyberSentry installed For the Device > Settings > Product Setup > Supervisory option, the panel looks like the following. Figure 5-4: Supervisory panel For the Security panel, the following settings are available. 5-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 233 Administrator is to re-enable Device authentication when Device authentication is disabled. To re-enable Device authentication, the Supervisor unlocks the device for setting changes, and then the Administrator can re- enable Device authentication. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-19...
Page 234 LOGIN: Range: Administrator, Engineer, Supervisor,   None Operator, Factory (for factory use only), None  CHANGE LOCAL See page 5-21   PASSWORDS  SESSION See page 5-22   SETTINGS 5-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 235 • Observer — This role has read-only access to all F60 settings. This role allows unlimited concurrent access but it has no download access to any files on the device. Observer is the default role if no authentication has been done to the device.
Page 236 In Device authentication mode, the Observer role does not have a password associated with it. In Server authentication mode the Observer role requires a password. If you are locked out of the software, contact GE Grid Solutions for the default password. When using CyberSentry, the default password is "ChangeMe1#".
Page 237 SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY  SELF TESTS  SELF TESTS  FAILED See below   AUTHENTICATE  FIRMWARE LOCK: Range: Enabled, Disabled  Enabled SETTINGS LOCK: Range: Enabled, Disabled  Enabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-23...
Page 238 After making any required changes, log out. When changing settings offline, ensure that only settings permitted by the role that performs the settings download are changed because only those changes are applied. 5-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 239 Clear Energy command (not applicable to all UR products) Clear Unauthorized Access command Clear Teleprotection Counters command (not applicable to all UR products) Clear All Relay Records command Role Log in Role Log off F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-25...
Page 240: Display Properties
PRODUCT SETUP CHAPTER 5: SETTINGS In addition to supporting syslog, a F60 with CyberSentry also saves the security events in two local security files, these being SECURITY_EVENTS.CSV and SETTING_CHANGES.LOG. Details on these files and how to retrieve them are available in the EnerVista software under Maintenance >...
Page 241 Some customers prefer very low currents to display as zero, while others prefer the current to display even when the value reflects noise rather than the actual signal. The F60 applies a cut-off value to the magnitudes and angles of the measured currents.
Page 242: Graphical Front Panel
The path is Settings > Product Setup > Graphical Panel > Home Page. The menu does not display when there is no graphical front panel. 5-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 243 Whenever an annunciator window changes state this list is re-evaluated, which can result in the home page displaying a different annunciator page. The Tabular option displays a configured actual values/metering page. The Targets option displays error messages. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-29...
Page 244 If the display rolls, the rolling mode pages remain displaying regardless of the home page or rolling mode delay specified. Each page displays for a few seconds; duration cannot be set. The path is Settings > Product Setup > Graphical Panel > Rolling Mode. 5-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 245 Range: 1 to 10 in steps of 1 Default: 1 This setting specifies the number of rolling pages. During rolling mode, the graphical front panel displays pages from 1 to the selected number. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-31...
Page 246 Metering Tab pushbutton on the graphical front panel. The Metering Editor is not used. The figures show setup and preview for monitoring actual values in a table on the graphical front panel. 5-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 247 A maximum of eight Status Inputs can be used per metering page, and 16 in all metering pages. Select the metering input from the drop-down list. The options reflect the FlexLogic operands applicable to the F60. They are inputs for all five metering pages, not just the current page.
Page 248 Range: 24-bit color selector Default: Black Set the text color to display in the specified cell. BACK COLOR Range: 24-bit color selector Default: Grey Set the background color to display for the specified cell. 5-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 249 Range: 1 to 12 in steps of 1 Default: 1 This setting specifies the number of integers in the displayed metered value. It can be used to provide for leading character spacing of the display value. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-35...
Page 250 User-Programmable Self Tests (not shown). When the alarms are triggered, they display with a red background. An alarm is acknowledged by using the arrow keys on the graphical front panel then pressing the Enter button. 5-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 251 Range: up to 20 alphanumeric characters Default: Page 1...Page 8 Up to 20 characters can be input as the name of each annunciator page. The number of pages depends on the Layout. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-37...
Page 252 The background color to display for any triggered cell, for example when alarm is triggered. Configure Range: Configure Default: Configure The Configure button becomes active when the CONTENT field is set to "Actual" or "Mixed." The window configures metered values. 5-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 253 (such as wrong password), IRIG-B clock failure, or breaker trouble, the Event Records display. When a breaker opens, a single-line diagram displays. For the Ethernet and IRIG-B failure operation to work, these functions also have been enabled under Settings > Product Setup > User-Programmable Self Tests. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-39...
Page 254: Clear Relay Records
SETTINGS  PRODUCT SETUP  CLEAR RELAY RECORDS  CLEAR RELAY CLEAR FAULT REPORTS: Range: FlexLogic operand   RECORDS CLEAR EVENT RECORDS: Range: FlexLogic operand  CLEAR OSCILLOGRAPHY: Range: FlexLogic operand  5-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 255: Communications
Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user- programmable pushbuttons to clear specific records is a typical application for these commands. Since the F60 responds to rising edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Page 256 5.3.5.3 Ethernet network topology The F60 has three Ethernet ports. Each Ethernet port must belong to a different network or subnetwork. Configure the IP address and subnet to ensure that each port meets this requirement. Two subnets are different when the bitwise AND operation performed between their respective IP address and mask produces a different result.
Page 257 SCADA is provided through LAN2. P2 and P3 are connected to LAN2, where P2 is the primary channel and P3 is the redundant channel. In this configuration, P3 uses the IP and MAC addresses of P2. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-43...
Page 258 LAN2, to which port 2 (P2) is connected, and communications with SCADA on LAN3, to which port 3 (P3) is connected. There is no redundancy. Figure 5-15: Multiple LANS, no redundancy 5-44 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 259 IP addresses and mask. Configure the network IP and subnet settings before configuring the routing settings. To obtain a list of all port numbers used, for example for audit purposes, contact GE technical support with substantiating information, such as the serial number and order code of your device.
Page 260 2 is performed. The delay in switching back ensures that rebooted switching devices connected to the F60, which signal their ports as active prior to being completely functional, have time to completely initialize themselves and become active. Once port 2 is active again, port 3 returns to standby mode.
Page 261 UR 7 redundancy Failover is selected for redundancy. 5.3.5.6 Parallel Redundancy Protocol (PRP) The F60 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 262 Delete the default route by replacing the default gateway with the default value of 127.0.0.1. General conditions to be satisfied by static routes The following rules are validated internally: 5-48 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 263 Port 2 (IP address 10.1.2.2) connects the UR to LAN 10.1.2.0/24 and to the EnerVista software through Router2. Router2 has an interface on 10.1.2.0/24 and the IP address of this interface is 10.1.2.1. The configuration before release 7.10 was as follows: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-49...
Page 264 SETTINGS  PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL  MODBUS PROTOCOL MODBUS SLAVE Range: 1 to 254 in steps of 1   ADDRESS: 254 MODBUS TCP PORT Range: 0 to 65535 in steps of 1  NUMBER(502): 502 5-50 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 265 0 disables Modbus over TCP/IP, meaning closes the Modbus TCP port. When the port number is changed to 0, the change takes effect when the F60 is restarted. When it is set to 0, use the front panel or serial port to communicate with the relay.
Page 266 DNP UNSOL RESPONSE Range: 0 to 65519 in steps of 1  DEST ADDRESS: 1 DNP CURRENT SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000,  FACTOR: 1 100000, 1000000, 10000000, 100000000 5-52 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 267 Range: 0 to 32 in steps of 1  CONTROL POINTS: 0 DNP TCP CONNECTION Range: 10 to 7200 s in steps of 1  TIMEOUT: 120 s DNP EVENT TIME BASE: Range: UTC, LOCAL  LOCAL F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-53...
Page 268 DNP ADDRESS unique address to each DNP slave. The F60 can specify a maximum of five clients for its DNP connections. These are IP addresses for the controllers to which the F60 can connect. The settings follow. SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP NETWORK CLIENT ADDRESSES ...
Page 269 DNP TCP connection for greater than the time specified by this setting, the connection is aborted by the F60. This frees up the connection to be re-used by a client. For any change to take effect, restart the relay.
Page 270 60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored. 5.3.5.12 IEC 61850 protocol The F60 is provided with optional IEC 61850 communications. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 271 The maximum number of simultaneous clients supported by the UR family is five. EnerVista setup for IEC 61850 The EnerVista UR Setup software provides the interface to configure F60 settings for the IEC 61850 protocol. This section describes this interface. The software also supports import/export and merging of IEC 61850 Substation Configuration Language (SCL) files as documented in the UR Family Communications Guide.
Page 272 Figure 5-19: IEC 61850 panel Opening the IEC 61850 window while online causes the UR Setup software to retrieve and import an SCL file from the F60. This System Configuration Description (SCD) file contains all the settings in the UR at the time of the file request, both those that are mapped into the IEC 61850 information model (that is, the "public"...
Page 273 When the Save button is clicked in the online IEC 61850 window, UR Setup software prepares a configured IED description (CID) file containing all the settings of the UR and sends the CID file to the F60. Upon receipt, the F60 checks the CID file for correctness, going out of service, then back into service when the CID file is accepted.
Page 274 Range: status-only, direct-with-normal-security, sbo-with-normal-security Default: sbo-with-normal-security This setting specifies the control service that clients must use to control the TEST MODE FUNCTION of the F60. An "on" control to <LDName>/LLN0.Mod changes TEST MODE FUNCTION to Disabled, an "on-blocked" control changes it to Forcible, and a "test/blocked"...
Page 275 The LLN0 in the Master logical device, which includes setting group, GOOSE and report control blocks, and datasets • LPHD1 — Models common issues for physical devices • GGIO1 — For unmapped FlexLogic operands F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-61...
Page 276 Figure 5-23: Menu for logical node If the insert option is selected, or the edit option is selected for other than the Master logical device, a logical device parameters edit dialog opens. 5-62 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 277 Each logical device inst name is required to be unique within the device, and it cannot be blank. Also, if the corresponding functional ldName setting is blank, the concatenation of the IED name and the logical device F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-63...
Page 278 The UR increments the value of paramRev by one whenever one or multiple setting changes occurs in one Modbus write request by any means (front panel, Modbus, or MMS) other than by SCL file 5-64 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 279 A v7.4 device can send an R-GOOSE message to another v7.4 device when both have R-GOOSE active as the protocol • A v7.4 device can send a GOOSE message to another v7.4 device when both have GOOSE active as the protocol F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-65...
Page 280 Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > TxGOOSE > TxGOOSE1 to access the settings for the first TxGOOSE. The settings and functionality for the others are similar. 5-66 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 281 Range: 0 to 129 VisibleString characters Default: TxGOOSE1 The entered value sets the goID value published in TxGOOSE1 messages, and can be used by subscribers to discriminate the TxGOOSE1 messages from other GOOSE messages. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-67...
Page 282 VID values of 0 and 1 are assigned by IEEE 802.1Q to other functions and are not to be used for GOOSE. 5-68 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 283 Also, Port 3 configuration in the CID file is ignored. The Port 3 ConnectedAP elements has no meaning, as ports 2 and 3 use the port 2 MAC address, IP address, and mask. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-69...
Page 284 (test field in edition 1.0 messages) are accepted only when the UR Test Mode Function setting is set to Forcible or Isolated. RxGOOSE messages can be received through any UR Ethernet port. 5-70 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 285 RxGOOSE1 messages. An entered address of zero disables RxGOOSE1. If the publisher is a UR series 7.3x device, the setting needs to match the value of the publisher’s TxGOOSE DST MAC setting. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-71...
Page 286 <GoCBName> is the name of the publishing control block. The F60 translates the ACSI format required for this setting to the MMS format used in GOOSE messages: <LDName>/LLN0$GO$<GoCBName> If the publisher is a UR 7.3x or 7.40 series device, <LDName> is the value of the publisher's Master functional ldName setting if that setting is not empty, otherwise it is the value of the publisher's IED NAME suffixed with "Master".
Page 287 7.40 UR Setup RxGOOSE Inputs pages. In this case the Member setting displays as the product-related name used by the publishing IED of the data object or data attribute, in standard SCSM format (e.g. Publisher1LD1/LLN0$ST$Off$stVal). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-73...
Page 288 (supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. The figure shows a selection being made by importing a CID file using the Add IED function. 5-74 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 289 This setting selects the logic state for the RxGOOSE Boolean1 FlexLogic operand if the UR has just completed startup and the selected RxGOOSE has not yet received a message, or the selected RxGOOSE has lost its connectivity with the publisher. The following choices are available: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-75...
Page 290 Range: None, RxGOOSE1, RxGOOSE2, and so on Default: None This setting selects the GOOSE message containing the value that drives the RxGOOSE DPS1 FlexLogic operand. If set to None, the RxGOOSE DPS1 FlexLogic operand assumes its default state. 5-76 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 291 (supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. Figure 5-31: RxGOOSE Analog Inputs panel There are 32 RxGOOSE analog inputs. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-77...
Page 292 Range: 0.000 to 1000000000.000 in steps of 0.001 Default: 1.000 This setting specifies the per-unit base value for other F60 features to use with the RxGOOSE Analog1 operand. A FlexElement for instance subtracts two quantities after converting their values to integers rescaled to a common base, the common base being the largest of the base values of the two quantities.
Page 293 RptEna attribute is false. Buffered and unbuffered reports Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports > Buffered Reports or Unbuffered Reports. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-79...
Page 294 Also, the control block can be configured to send integrity reports containing the present value of all members either on demand from the client or periodically. A TCP handshaking mechanism causes messages that are not read and acknowledged by the client to be retransmitted. 5-80 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 295 Control blocks and data sets can be pre-configured by sending the F60 a CID file. See the UR Family Communications Guide for details. EnerVista UR Setup also can be used to select the data set members and to pre-configure the control blocks.
Page 296 This setting selects the data set whose members' status is reported in Unbuffered Report1 messages using the UR Setup software designator for the data set. The IEC 61850 name of the data sets are configured in the Datasets panel, as described later. 5-82 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 297 DataSets Navigate to Settings > Product Setup > Communications > IEC 61850 > DataSets. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-83...
Page 298 The DataSet name is not copied or pasted. In short, use this feature to copy a DataSet Member setting and paste it into another Member setting, a text file, or Word, as examples. 5-84 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 299 Select the member from the drop-down list. Or right-click an entry to copy, paste, delete, or insert. Product setup Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-85...
Page 300 Deadband parameters of measured values related to the Energy metering are configured here. Real Time Clock Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup > Real Time Clock. 5-86 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 301 The analog value that each deadband setting applies is usually obvious from the name of the setting. However, a tabulation of the analog values and their associated deadband setting can be found in the UR Family Communications Guide. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-87...
Page 302 Auxiliary voltage — 275 x auxiliary VT ration setting • Power (real, reactive, apparent, 3-phase, and 1-phase) — 4 × phase CT primary setting × 1.5 × VT Secondary setting × VT ratio setting 5-88 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 303 While the selected operand is asserted, Bkr0XCBR1.Loc.stVal is true and IEC 61850 commands to BkrCSWI1.Pos and Bkr0XCBR1.Pos are not accepted, and a Negative Response (-Rsp) is issued with the REASON CODE of Blocked-by- switching-hierarchy. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-89...
Page 304 Bkr0XCBR1.BlkOpn.ctlVal signal on the Breaker Control Logic (Sheet 1 of 2) diagram in the Settings > System Setup section later. This signal when true blocks breaker 1 trip control while the operand selected by setting XCBR1 ST.LOC OPERAND is not active. 5-90 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 305 Navigate to Settings > Product Setup > Communications > IEC 61850 > System Setup > Switches > Switch 1 to access the settings that configure the IEC 61850 protocol interface with the first disconnect switch control and status monitoring element. The settings and functionality for the others are similar. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-91...
Page 306 > System Setup section later. These signals force a disconnect switch trip or close control while the operand selected by setting XSWI1 ST.LOC OPERAND is not active. "sbo" here is select-before-operate. Enhanced security means that the F60 reports to the client the disconnect switch 1 position the end of the command sequence.
Page 307 SelectEditSG. The setting related to these IEC 61850 commands are described here. Navigate to Settings > Product Setup > Communications > IEC 61850 > Control Elements > Setting Groups to access the setting that configures the IEC 61850 setting group commands. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-93...
Page 308 Navigate to Settings > Product Setup > Communications > IEC 61850 > Settings for Commands to access the settings that configure the IEC 61850 protocol interface for record clear commands. Figure 5-43: Commands panel 5-94 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 309 This setting selects the control model clients must use to successfully control the command CLEAR FAULT REPORTS. "sbo" here is select-before-operate. Enhanced security means that the F60 reports to the client the breaker 1 position at the end of the command sequence.
Page 310 Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO2 to access the settings that configure the IEC 61850 protocol interface for Virtual Input commands. Figure 5-45: GGIO2 panel 5-96 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 311 <LDName>/GGIO4.AnIn01.instMag.f. The value of the FlexAnalog operand is converted automatically to the format and scaling required by the standard, that is to say primary amperes, primary volts, and so on. See Appendix A for a list of FlexAnalog operands. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-97...
Page 312 File transfer by IEC 61850 The F60 supports file transfer by IEC 61850. The approach is as follows, using the SISCO AX-S4 61850 client software as an example. In the AX-S4 61850 Explorer window, click the Tools menu and access the SISCO File Transfer Utility.
Page 313 NUMBER(80): 80 The F60 contains an embedded web server and can display pages in a web browser. The web pages are organized as a series of menus that can be accessed starting at the F60 “Main Menu.” Web pages are read-only and are available showing DNP and IEC 60870-5-104 points lists, Modbus registers, event records, fault reports, and so on.
Page 314 NUMBER: 0 The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the F60 over a network. The F60 operates as a TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file obtained from the F60 contains a list and description of all available files, for example event records and oscillography.
Page 315 COMMUNICATIONS  PROTOCOL connected to a maximum of two masters (usually either an RTU or a SCADA master station). Since the F60 maintains two sets of IEC 60870-5-104 data change buffers, ideally no more than two masters actively communicate with the F60 at one time.
Page 316 CHAPTER 5: SETTINGS The F60 can specify a maximum of five clients for its IEC 104 connections. These are IP addresses for the controllers to which the F60 can connect. A maximum of two simultaneous connections are supported at any given time.
Page 317 EXCH 1 DATA ITEM 1 to 20/50 from the F60 memory map can be configured to be included in an EGD exchange. The settings are the starting Modbus register address for the data item in decimal format. See the Modbus memory map in the UR Series Communications Guide for details.
Page 318 PTP, or SNTP, its time is overwritten by these three sources, if any of them is active. If the synchronization timeout occurs and none of IRIG-B, PTP, or SNTP is active, the F60 sets the invalid bit in the time stamp of a time-tagged message.
Page 319 Spontaneous transmission occurs as a response to cyclic Class 2 requests. If the F60 wants to transmit Class 1 data at that time, it demands access for Class 1 data transmission (ACD=1 in the control field of the response).
Page 320 FlexAnalog operands. The measurands sent are voltage, current, power, power factor, and frequency. If any other FlexAnalog is chosen, the F60 sends 0 instead of its value. Note that the power is transmitted in KW, not W. Measurands are transmitted as ASDU 3 or ASDU 9 (type identification value set to measurands I, respectively measurands II).
Page 321 Range: Virtual input  COMMAND 31 OFF: Range: Virtual input  Commands are received as General Command (Type Identification 20). The user can configure the action to perform when an ASDU command comes. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-107...
Page 322: Modbus User Map
PRODUCT SETUP CHAPTER 5: SETTINGS A list of available mappings is provided on the F60. This includes 64 virtual inputs (see the following table). The ON and OFF for the same ASDU command can be mapped to different virtual inputs.
Page 323: Real-Time Clock
Setup for IRIG-B is illustrated in the Installation chapter. For the Other protocols, whenever a time synchronization message is received through any of the active protocols, the F60 clock updates. However, given that IEC 60870-5-103, IEC 60870-5-104, Modbus, and DNP are low-accuracy time synchronization methods, avoid their use for synchronization when better accuracy time protocols, such as IRIG-B and PTP, are active in the system.
Page 324 See the Order Codes section in chapter 2 for details. The F60 supports the Precision Time Protocol (PTP) specified in IEEE Std 1588 2008 using the Power Profile (PP) specified in IEEE Std C37.238 2011. This enables the relay to synchronize to the international time standard over an Ethernet network that implements PP.
Page 325 When a clock on start-up discovers that it is “better” than the present grandmaster, it assumes the grandmaster role and the previous grandmaster reverts to slave. The F60 qualification mechanism accepts a potential master clock as a new grandmaster, when in a four-second interval it has received three announce messages from it, all better than the present grandmaster clock and better than any other announce in this interval.
Page 326 F60 clock is closely synchronized with the SNTP/ NTP server. It takes up to two minutes for the F60 to signal an SNTP self-test error if the server is offline.
Page 327: Fault Reports
 2:00 The F60 maintains two times: local time and Universal Coordinated Time (UTC). Local time can be provided by IRIG-B signals. UTC time is provided by SNTP servers. The real-time clock (RTC) and time stamps reported in historical records and communication protocols can be incorrect if the Local Time settings are not configured properly.
Page 328 MAG: 0.00 Ω The F60 relay supports one fault report and an associated fault locator per CT bank to a maximum of three. The signal source and trigger condition, as well as the characteristics of the line or feeder, are entered in this menu.
Page 329: Oscillography
Range: 0 to 100% in steps of 1  TRIGGER SOURCE: Range: FlexLogic operand  AC INPUT WAVEFORMS: Range: Off; 8, 16, 32, 64 samples/cycle  16 samples/cycle  DIGITAL CHANNELS See below   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-115...
Page 330 When changes are made to the oscillography settings, all existing oscillography records are cleared. 5.3.9.2 Digital channels SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  DIGITAL CHANNELS  DIGITAL CHANNELS DIGITAL CHANNEL 1: Range: FlexLogic operand    DIGITAL CHANNEL 63: Range: FlexLogic operand  5-116 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 331: Data Logger
Analog channel 1 ↔ 3rd harmonic Analog channel 23 ↔ 25th harmonic 5.3.10 Data logger SETTINGS  PRODUCT SETUP  DATA LOGGER  DATA LOGGER DATA LOGGER MODE: Range: Continuous, Trigger   Continuous F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-117...
Page 332 This setting only applies when the mode is set to “Trigger.” — This setting selects the time interval at which the actual value data is recorded. DATA LOGGER RATE 5-118 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 333: Demand
The figure shows the 90% thermal response time characteristic of 15 minutes. A setpoint establishes the time to reach 90% of a steady-state value, just as the response time of an analog instrument. A steady state value applied for twice the response time indicates 99% of the value. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-119...
Page 334: User-Programmable Leds
See below   LEDS   TRIP & ALARM LEDS See page 5-123    USER-PROGRAMMABLE See page 5-123   LED 1   USER-PROGRAMMABLE   LED 48 5-120 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 335 Additionally, stages 2 and 3 are repeated twice for the five device status LEDs and nine event cause LEDs, one time with green color on and the other with red color on. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-121...
Page 336 Configure the LED test to recognize user-programmable pushbutton 1 by making the following entries in the SETTINGS  menu: PRODUCT SETUP  USER-PROGRAMMABLE LEDS  LED TEST : “Enabled” LED TEST FUNCTION “PUSHBUTTON 1 LED TEST CONTROL ON” 5-122 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 337 “Latched,” the LED, once lit, remains so until reset by the front panel button, from a remote device via a RESET communications channel, or from any programmed operand, even if the LED operand state de-asserts. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-123...
Page 338 Event Cause LED 7 LED PHASE B EVENT CAUSE LED 7 Orange Event Cause LED 8 LED PHASE C EVENT CAUSE LED 8 Orange Event Cause LED 9 LED NEUTRAL/GROUND EVENT CAUSE LED 9 Orange 5-124 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 339: User-Programmable Self-Tests
There are three standard control pushbuttons, labelled USER 1, USER 2, and USER 3, on the standard and enhanced front panels. These are user-programmable and can be used for various applications such as performing an LED test, switching setting groups, and invoking and scrolling though user-programmable displays. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-125...
Page 340 The location of the control pushbuttons are shown in the following figures. Figure 5-52: Control pushbuttons (enhanced front panel) An additional four control pushbuttons are included on the standard front panel when the F60 is ordered with the 12 user- programmable pushbutton option.
Page 341: User-Programmable Pushbuttons
Range: 0 to 60.00 s in steps of 0.05  TIME: 0.00 s PUSHBTN 1 LED CTL: Range: FlexLogic operand  PUSHBTN 1 MESSAGE: Range: Disabled, Normal, High Priority  Disabled PUSHBUTTON 1 Range: Disabled, Enabled  EVENTS: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-127...
Page 342 PRODUCT SETUP CHAPTER 5: SETTINGS The F60 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. User-programmable pushbuttons provide an easy and error-free method of entering digital state (on, off) information. The number depends on the front panel ordered.
Page 343 The pulse duration of the remote set or local front panel pushbutton must be at least 50 ms to operate the pushbutton. This allows the user-programmable pushbuttons to properly operate during power cycling events and various system disturbances that can cause transient assertion of the operating signals. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-129...
Page 344 PUSHBTN 1 AUTORST DELAY mode. — This setting assigns the FlexLogic operand serving to inhibit user-programmable pushbutton PUSHBTN 1 REMOTE operation from the operand assigned to the settings. PUSHBTN 1 SET PUSHBTN 1 RESET 5-130 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 345 10 seconds. — If this setting is enabled, each user-programmable pushbutton state change is logged as an PUSHBUTTON 1 EVENTS event into the event recorder. The figures show the user-programmable pushbutton logic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-131...
Page 346 PRODUCT SETUP CHAPTER 5: SETTINGS Figure 5-58: User-programmable pushbutton logic (Sheet 1 of 2) 5-132 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 347: Flex State Parameters
The state bits can be read out in the “Flex States” register array beginning at Modbus address 0900h. Sixteen states are packed into each register, with the lowest-numbered state in the lowest-order bit. Sixteen registers accommodate the 256 state bits. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-133...
Page 348: User-Definable Displays
When this type of entry occurs, the sub-menus are automatically configured with the proper content—this content can be edited subsequently. 5-134 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 349 If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the bottom line only. The units are only displayed on both lines if the units specified both the top and bottom line items are different. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-135...
Page 350: Direct Inputs And Outputs
DIRECT OUTPUT DEVICE ID messages. All UR-series IEDs in a ring need to have unique numbers assigned. The IED ID is used to identify the sender of the direct input and output message. 5-136 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 351 DIRECT I/O DATA RATE setting applies to a F60 with dual-channel communication cards and allows crossing DIRECT I/O CHANNEL CROSSOVER over messages from channel 1 to channel 2. This places all UR-series IEDs into one direct input and output network regardless of the physical media of the two communication channels.
Page 352 DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: DIRECT OUTPUT DEVICE ID: “2” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 3: 5-138 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 353 Figure 5-63: Three-terminal line application A permissive pilot-aided scheme can be implemented in a two-ring configuration, shown as follows (IEDs 1 and 2 constitute a first ring, while IEDs 2 and 3 constitute a second ring). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-139...
Page 354 In this application, apply the following settings. For UR-series IED 1: DIRECT OUTPUT DEVICE ID: “1” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: 5-140 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 355 EVENTS: Disabled The F60 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The monitoring function counts all incoming messages, including messages that failed the CRC check.
Page 356: Teleprotection
 EVENTS: Disabled The F60 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unreturned messages.
Page 357: Remote Resources
5.4 Remote resources 5.4.1 Remote resources configuration When the F60 is ordered with a process card module as a part of HardFiber system, an additional Remote Resources menu tree is available in the EnerVista software to allow configuration of the HardFiber system.
Page 358 Bricks. Remote resources settings configure the point-to-point connection between specific fiber optic ports on the F60 process card and specific Brick. The relay is then configured to measure specific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
Page 359: Ac Inputs
The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5.5.1.2 Voltage banks SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK F5(M5)  VOLTAGE BANK F5 PHASE VT F5 Range: Wye, Delta   CONNECTION: Wye F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-145...
Page 360: Power System
5-146 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 361: Signal Sources
“Disabled” only in unusual circumstances; consult GE Grid Solutions for special variable- FREQUENCY TRACKING frequency applications. The frequency tracking feature functions only when the F60 is in the “Programmed” mode. If the F60 is “Not Programmed,” then metering values are available but can exhibit significant errors. 5.5.3 Signal sources SETTINGS ...
Page 362 CHAPTER 5: SETTINGS When the F60 is equipped with a type 8Z CT/VT module for high impedance fault detection, do not assign the CT bank of this module to a source that is used by any conventional protection element. The type 8Z module CT bank is used solely by the high impedance fault detection algorithm.
Page 363 CT/VT inputs that are used to provide the data. Figure 5-68: Example of use of sources Y LV D HV SRC 1 SRC 2 SRC 3 Phase CT F1+F5 None Ground CT None None Phase VT None None F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-149...
Page 364: Breakers
 BREAKER 1 ΦC OPENED: Range: FlexLogic operand  BREAKER 1 TOPERATE: Range: 0 to 65535 s in steps of 1  70 ms BREAKER 1 EXT ALARM: Range: FlexLogic operand  5-150 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 365 — Selects an operand that prevents initiation of Breaker 1 close commands. This setting can be used BREAKER 1 BLK CLOSE for blocking circuit breaker closing, for instance to prevent closing into a closed ground switch. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-151...
Page 366 If this setting is set to Off, the racked status is not considered. 5-152 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 367 CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-69: Dual breaker control logic (Sheet 1 of 3) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-153...
Page 368 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-70: Dual breaker control logic (Sheet 2 of 3) 5-154 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 369: Disconnect Switch Control
Range: Disabled, Enabled   FUNCTION: Disabled SWITCH 1 NAME: Range: up to six alphanumeric characters  SW 1 SWITCH 1 MODE: Range: 3-Pole, 1-Pole  3-Pole SWITCH 1 OPEN: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-155...
Page 370 — This setting selects “3-Pole” mode, where disconnect switch poles have a single common auxiliary SWITCH 1 MODE switch, or “1-Pole” mode where each disconnect switch pole has its own auxiliary switch. 5-156 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 371 — This setting specifies the delay interval during which a disagreement of status among the pole SWITCH 1 ALARM DELAY position tracking operands do not declare a pole disagreement. This allows for non-simultaneous operation of the poles. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-157...
Page 372 CHAPTER 5: SETTINGS IEC 61850 functionality is permitted when the F60 is in “Programmed” mode and not in local control mode. The switch element has direct hard-coded connections to the IEC 61850 model as shown in the logic diagrams. This allows remote open/close operation of each switch, using either CSWI or XSWI IEC 61850 logical nodes.
Page 373 CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-73: Disconnect switch control status logic (sheet 2 of 3) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-159...
Page 374: Flexcurves
FlexCurve, enter the reset and operate times (using the keys) for each selected pickup point (using the VALUE up/down keys) for the required protection curve (A, B, C, or D). MESSAGE 5-160 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 375 The recloser curve configuration window shown here appears when the Initialize From setting in the EnerVista software is set to “Recloser Curve” and the Initialize FlexCurve button is clicked. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-161...
Page 376 MRT and from then onwards the operating time remains at 200 ms. Figure 5-76: Composite recloser curve with HCT disabled With the HCT feature enabled, the operating time reduces to 30 ms for pickup multiples exceeding eight times pickup. 5-162 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 377 EnerVista software generates an error message and discards the proposed changes. 5.5.6.5 Standard recloser curves The following graphs display standard recloser curves available for the F60. Figure 5-78: Recloser curves GE101 to GE106 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 378 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-79: Recloser curves GE113, GE120, GE138, and GE142 Figure 5-80: Recloser curves GE134, GE137, GE140, GE151, and GE201 5-164 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 379 CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-81: Recloser curves GE131, GE141, GE152, and GE200 Figure 5-82: Recloser curves GE133, GE161, GE162, GE163, GE164, and GE165 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-165...
Page 380 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-83: Recloser curves GE116, GE117, GE118, GE132, GE136, and GE139 Figure 5-84: Recloser curves GE107, GE111, GE112, GE114, GE115, GE121, and GE122 5-166 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 381: Phasor Measurement Unit
  CONFIGURATION The F60 is provided with an optional Phasor Measurement Unit (PMU) feature. This feature is specified as a software option at the time of ordering. The number of PMUs available also depends on this option. Using the order code for your device, see the order codes in chapter 2 for details.
Page 382 The figure shows an example of an N60 using four Logical Device PMUs (Logical Device 2 through 5) and four aggregators. The control blocks for the aggregators are located in LD1. A 64 character LDName setting is provided. 5-168 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 383 MxxMMXU1 ClcMth = M-Class (Note Vaux is mapped to Vneut of MMXU) • MxxMSQI1 ClcMth = M-CLASS • NxxMMXU1 ClcMth = M-Class (Note Vaux is mapped to Vneut of MMXU) • NxxMSQI1 ClcMth = M-CLASS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-169...
Page 384 The mapping is implemented as STN-IDCode (text string). From each PMU, the user selects the phasor information of interest that is mapped into the selected aggregator datset(s). For version 7.0 and later, only FCDA data is supported. 5-170 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 385 5.5.7.6 Configuration example: CFG-2 based configuration (using IEC 61850-90-5) The F60 is expected to send the CFG-2 file (IEEE C37.118 config. file) upon request from the upstream synchrophasor devices (for example, P30) without stopping R-SV multicasting, as shown in the following figure. The primary domain controller (PDC) does not need to use a stop/start data stream command if the UR protocol is set to IEC 61850-90-5 prior to requesting the configuration via CFG-2 (IEEE C37.118 config.
Page 386 FUNCTION: Disabled PMU 1 IDCODE: Range: 1 to 65534 in steps of 1  PMU 1 STN: Range: 32-character ASCII string truncated to 16  characters if mapped into C37.118 Default: GE-UR-PMU GE-UR-PMU 5-172 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 387 PMU 1 D-CH-16 Range: 16-character ASCII string  NM: Dig Channel 16 PMU 1 D-CH- 1 Range: Off, On  NORMAL STATE: Off  PMU 1 D-CH-16: Range: Off, On  NORMAL STATE: Off F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-173...
Page 388 10 Hz, 12 Hz, 15 Hz, 20 Hz, 30 Hz, 60 Hz, or 120 Hz (or 10 Hz, 25 Hz, 50 Hz, or 100 Hz when the system frequency is 50 Hz) when entered via the keypad or software; and the F60 stops the transmission of reports.
Page 389 (magnitude and angle) coordinates. This setting complies with bit-0 of the FORMAT field of the IEEE C37.118 configuration frame. With 90-5 PMU, the FORMAT and STYLE are Floating-point and Polar respectively, as specified in the IEC 61850-90-5 technical report. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-175...
Page 390 MAG: 100.0% PMU 1 IG CALIBRATION Range: –5.00 to 5.00° in steps of 0.05  ANGLE: 0.00° PMU 1 IG CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%  MAG: 100.0% 5-176 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 391 When receiving synchrophasor data at multiple locations, with possibly different reference nodes, it can be more beneficial to allow the central locations to perform the compensation of sequence voltages. • This setting applies to PMU data only. The F60 calculates symmetrical voltages independently for protection and control purposes without applying this correction. •...
Page 392 PMU 1 FREQ TRIGGER Range: 20.00 to 70.00 Hz in steps of 0.01  LOW-FREQ: 49.00 Hz PMU 1 FREQ TRIGGER Range: 20.00 to 70.00 Hz in steps of 0.01  HIGH-FREQ: 61.00 Hz 5-178 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 393 F60 standards. This element requires that the frequency be above the minimum measurable value. If the frequency is below this value, such as when the circuit is de-energized, the trigger drops out.
Page 394 Range: 0.00 to 600.00 s in steps of 0.01  DPO TIME: 1.00 s PMU 1 CURR TRIG BLK: Range: FlexLogic operand  PMU 1 CURR TRIGGER Range: Self-reset, Latched, Disabled  TARGET: Self-reset 5-180 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 395 The trigger responds to the single-phase and three-phase power signals of the Phasor Measurement Unit (PMU) source. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-181...
Page 396 Range: 0.00 to 600.00 s in steps of 0.01  DPO TIME: 1.00 s PMU 1 df/dt TRG BLK: Range: FlexLogic operand  PMU 1 df/dt TRIGGER Range: Self-reset, Latched, Disabled  TARGET: Self-reset 5-182 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 397 “Automatic Overwrite,” the last record is erased to facilitate new recording, when triggered. Under the “Protected” selection, the recorder stops creating new records when the entire memory is used up by the old uncleared records. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-183...
Page 398 FlexLogic operands are updated, and the five-second timer restarts. This setting enables or disables the control. When enabled, all 16 operands for each aggregator are active; when disabled, all 16 operands for each aggregator remain reset. 5-184 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 399 ASDU at T-2 (previous values) + ASDU at T-1 (previous values) + ASDU at T0 (current values) ASDU at T-3 (previous values) + ASDU at T-2 (previous values) + ASDU at T-1 (previous values) + ASDU at T0 (current values) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-185...
Page 400 0 state, the remote client writes to the reserve bit, the SvEna is rejected by the UR, and a negative response with the appropriate Service Error is returned to the client. 5-186 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 401: Flexlogic
FlexLogic. In general, the system receives analog and digital inputs that it uses to produce analog and digital outputs. The figure shows major subsystems of a generic UR-series relay involved in this process. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-187...
Page 402 Figure 5-99: UR architecture overview The states of all digital signals used in the F60 are represented by flags (or FlexLogic operands, which are described later in this section). A digital “1” is represented by a set flag. Any external contact change-of-state can be used to block an element from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output.
Page 403 The following table lists the operands available for the relay. The operands can be viewed online by entering the IP address of the relay in a web browser and accessing the Device Information Menu. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-189...
Page 404 Auxiliary AUX UV1 DPO Auxiliary undervoltage element has dropped out undervoltage AUX UV1 OP Auxiliary undervoltage element has operated AUX UV2 to 3 Same set of operands as shown for AUX UV1 5-190 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 405 BRK RESTRIKE 1 OP B Breaker restrike detected in phase B of the breaker control 1 element BRK RESTRIKE 1 OP C Breaker restrike detected in phase C of the breaker control 1 element F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-191...
Page 406 Same set of operands as shown for Counter 1 ELEMENT: DCB3 TX INIT Directional blocking signal is initiated Directional DCB3 TX STOP Directional blocking scheme de-asserts transmit signal comparison blocking DCB3 OP Directional blocking scheme has operated scheme (DCB3) 5-192 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 407 INCIPNT FLT 1 PKP B Asserted when incipient cable fault detector 1 picks up in phase B INCIPNT FLT 1 PKP C Asserted when incipient cable fault detector 1 picks up in phase C F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-193...
Page 408 Phase B directional 1 block overcurrent PH DIR1 BLK C Phase C directional 1 block PH DIR1 BLK Phase directional 1 block PH DIR2 Same set of operands as shown for PH DIR1 5-194 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 409 PMU 1 VOLT TRIGGER Abnormal voltage trigger of phasor measurement unit 1 has operated PMU 1 TRIGGERED Phasor measurement unit 1 triggered; no events or targets are generated by this operand F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-195...
Page 410 Source 1 VT neutral wire open detected. When the VT is connected in Delta, do not enable this function because there is no neutral wire for Delta connected VT. SRC2 VT FUSE FAIL to SRC4 Same set of operands as shown for SRC1 VT FF 5-196 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 411 Same set of operands as shown for THERMAL PROT 1 ELEMENT: TRIP BUS 1 PKP Asserted when the trip bus 1 element picks up Trip bus TRIP BUS 1 OP Asserted when the trip bus 1 element operates F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-197...
Page 412 Virt Op 1 Flag is set, logic=1 Virtual outputs Virt Op 2 Flag is set, logic=1 Virt Op 3 Flag is set, logic=1 ↓ ↓ Virt Op 96 Flag is set, logic=1 5-198 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 413 RxGOOSE 1 On Flag is set, logic=1 ↓ ↓ RxGOOSE 64 On Flag is set, logic=1 RxGOOSE 1 Off Flag is set, logic=1 ↓ ↓ RxGOOSE 64 Off Flag is set, logic=1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-199...
Page 414 ID of any of these operands, the assigned name appears in the relay list of operands. The default names are shown in the FlexLogic operands table. The characteristics of the logic gates are tabulated in the following table, and the operators available in FlexLogic are listed in the FlexLogic operators table. 5-200 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 415: Flexlogic Rules
Assigning the output of an operator to a virtual output terminates the equation. A timer operator (for example, "TIMER 1") or virtual output assignment (for example, " = Virt Op 1") can be used once F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-201...
Page 416: Flexlogic Evaluation
Inspect each operator between the initial operands and final virtual outputs to determine if the output from the operator is used as an input to more than one following operator. If so, the operator output must be assigned as a virtual output. 5-202 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 417 Figure 5-102: Logic for virtual output 3 Prepare a logic diagram for virtual output 4, replacing the logic ahead of virtual output 3 with a symbol identified as virtual output 3, shown as follows. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-203...
Page 418 Assume for this example that the state is to be ON for a closed contact. The operand is therefore “Cont Ip H1c On”. 5-204 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 419 [88] Virt Ip 1 On [89] DIG ELEM 1 PKP [90] XOR(2) [91] Virt Op 3 On [92] OR(4) [93] LATCH (S,R) [94] Virt Op 3 On [95] TIMER 1 [96] Cont Ip H1c On F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-205...
Page 420 Virt Op 1 On Virt Op 2 On Virt Ip 1 On DIG ELEM 1 PKP XOR(2) Virt Op 3 On OR(4) LATCH (S,R) Virt Op 3 On TIMER 1 Cont Ip H1c On OR(3) 5-206 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 421: Flexlogic Equation Editor
FLEXELEMENT 1 NAME: Range: up to six alphanumeric characters  FxE 1 FLEXELEMENT 1 +IN: Range: Off, any analog actual value parameter  FLEXELEMENT 1 -IN: Range: Off, any analog actual value parameter  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-207...
Page 422 The element can be programmed to respond either to a signal level or to a rate-of-change (delta) over a pre-defined period of time. The output operand is asserted when the operating signal is higher than a threshold or lower than a threshold, as per your choice. 5-208 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 423 — Enables the relay to respond to either high or low values of the operating signal. The following FLEXELEMENT 1 DIRECTION figure explains the application of the , and FLEXELEMENT 1 DIRECTION FLEXELEMENT 1 PICKUP FLEXELEMENT 1 HYSTERESIS settings. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-209...
Page 424 Figure 5-108: FlexElement direction, pickup, and hysteresis In conjunction with the setting, the element can be programmed to provide two extra FLEXELEMENT 1 INPUT MODE characteristics, as shown in the following figure. 5-210 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 425 (Brk X Arc Amp A, B, and C) DCmA BASE = maximum value of the DCMA INPUT MAX setting for the two transducers configured under the +IN and –IN inputs DELTA TIME BASE = 1 µs F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-211...
Page 426: Non-Volatile Latches
Typical applications include sustaining operator commands or permanently blocking relay functions, such as Autorecloser, until a deliberate interface action resets the latch. — This setting characterizes Latch 1 to be Set- or Reset-dominant. LATCH 1 TYPE 5-212 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 427: Grouped Elements
SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  SETTING GROUP 1  LOAD ENCROACHMENT See below     PHASE CURRENT See page 5-216    NEUTRAL CURRENT See page 5-228   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-213...
Page 428: Load Encroachment
Range: Self-reset, Latched, Disabled  TARGET: Self-reset LOAD ENCROACHMENT Range: Disabled, Enabled  EVENTS: Disabled The load encroachment element responds to the positive-sequence voltage and current and applies a characteristic as shown in the figure. 5-214 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 429 When the voltage is below this threshold, a blocking signal is not asserted by the element. When selecting this setting, remember that the F60 measures the phase-to-ground sequence voltages regardless of the VT connection. The nominal VT secondary voltage as specified with the SYSTEM SETUP ...
Page 430: Phase Current
 DIRECTIONAL 2 5.7.4.2 Inverse TOC curve characteristics The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t standard curve shapes. This allows for simplified coordination with downstream devices.
Page 431 IEEE Very Inverse 8.090 3.514 1.471 0.899 0.654 0.526 0.450 0.401 0.368 0.345 16.179 7.028 2.942 1.798 1.308 1.051 0.900 0.802 0.736 0.689 32.358 14.055 5.885 3.597 2.616 2.103 1.799 1.605 1.472 1.378 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-217...
Page 432 6.878 4.012 2.521 1.992 1.712 1.535 1.411 1.319 1.247 1.188 0.60 10.317 6.017 3.781 2.988 2.568 2.302 2.117 1.978 1.870 1.782 0.80 13.755 8.023 5.042 3.984 3.424 3.070 2.822 2.637 2.493 2.376 5-218 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 433 A to E = constants defined in the table = characteristic constant defined in the table = reset time in seconds (assuming energy capacity is 100% and RESET is “Timed”) RESET Table 5-34: GE type IAC inverse time curve constants IAC curve shape IAC Extreme Inverse 0.0040 0.6379...
Page 434 GROUPED ELEMENTS CHAPTER 5: SETTINGS IAC curve shape IAC Short Inverse 0.0428 0.0609 0.6200 –0.0010 0.0221 0.222 Table 5-35: GE type IAC curve trip times Multiplier Current ( I / I pickup (TDM) 10.0 IAC Extremely Inverse 1.699 0.749 0.303 0.178...
Page 435 T = Operate Time (in seconds) TDM = Multiplier setting I = Input Current = Pickup Current setting pickup = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-221...
Page 436 GROUPED ELEMENTS CHAPTER 5: SETTINGS Recloser curves The F60 uses the FlexCurve feature to facilitate programming of 41 recloser curves. See the FlexCurves settings section earlier in this chapter for details. 5.7.4.3 Phase time overcurrent (ANSI 51P, IEC PTOC) SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT  PHASE TOC1(6) ...
Page 437 — Selects the signal source for the phase time overcurrent protection element. SIGNAL SOURCE — Selects how phase current input quantities are interpreted by the F60. Inputs can be selected as fundamental INPUT phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 438 PHASE IOC1 BLOCK A: Range: FlexLogic operand   PHASE IOC1 BLOCK C: Range: FlexLogic operand  PHASE IOC1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset PHASE IOC1 Range: Disabled, Enabled  EVENTS: Disabled 5-224 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 439 Range: 0.004 to 3.000 pu in steps of 0.001  THRESHOLD: 0.700 pu PHASE DIR 1 BLOCK Range: No, Yes  WHEN V MEM EXP: No PHASE DIR 1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-225...
Page 440 (phase current) and the polarizing signal (the line voltage, shifted in the leading direction by the characteristic angle, ECA). The table shows the operating and polarizing signals used for phase directional control. 5-226 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 441 When set to "No," the directional element allows tripping of phase overcurrent elements under directional control. — This setting enables and disables the logging of phase directional overcurrent events in the PHASE DIR 1 EVENTS sequence of events recorder. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-227...
Page 442: Neutral Current
 NEUTRAL TOC 1 See below      NEUTRAL TOC 6    NEUTRAL IOC 1 See page 5-230     NEUTRAL IOC 12   5-228 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 443 — This setting selects the signal source for the neutral time overcurrent protection element. NEUTRAL TOC1 SIGNAL SOURCE — This setting selects how neutral current input quantities are interpreted by the F60. Inputs can be NEUTRAL TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 444 The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents resulting from: • System unbalances under heavy load conditions • Transformation errors of current transformers (CTs) during double-line and three-phase faults • Switch-off transients during double-line and three-phase faults 5-230 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 445 VOLT: Calculated V0 NEUTRAL DIR OC1 OP Range: Calculated 3I0, Measured IG  CURR: Calculated 3I0 NEUTRAL DIR OC1 POS- Range: 0.000 to 0.500 in steps of 0.001  SEQ RESTRAINT: 0.063 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-231...
Page 446 The following tables define the neutral directional overcurrent element. V_0 is the zero-sequence voltage, I_0 is the zero-sequence current, ECA is the element characteristic angle, and IG is the ground current. 5-232 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 447 This allows for better protection coordination. Take the bias into account when using the neutral directional overcurrent element to directionalize other protection elements. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-233...
Page 448 For example, if using an autotransformer neutral current as a polarizing source, ensure that a reversal of the ground current does not occur for a high-side fault. Assume that the 5-234 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 449 — This setting defines the pickup level for the overcurrent unit of the element in the reverse NEUTRAL DIR OC1 REV PICKUP direction. When selecting this setting, keep in mind that the design uses a positive-sequence restraint technique for the “Calculated 3I0” mode of operation. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-235...
Page 450: Wattmetric Ground Fault
OV PKP: 0.20 pu WATTMETRIC GND FLT 1 Range: Calculated IN, Measured IG  CURR: Calculated IN WATTMETRIC GND FLT 1 Range: 0.002 to 30.000 pu in steps of 0.001  OC PKP: 0.060 pu 5-236 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 451 WATTMETRIC GND FLT 1 PWR PKP the 1 pu voltage as specified for the overvoltage condition of this element, and 1 pu current as specified for the overcurrent condition of this element. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-237...
Page 452 The four FlexCurves allow for custom user-programmable time characteristics. When working with FlexCurves, the element uses the operate to pickup ratio, and the multiplier setting is not applied: Eq. 5-21 Again, the FlexCurve timer starts after the definite time timer expires. 5-238 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 453 Figure 5-123: Wattmetric characteristic angle response — This setting is applicable if the is set to Inverse and WATTMETRIC GND FLT 1 MULTIPLIER WATTMETRIC GND FLT 1 CURVE defines the multiplier factor for the inverse time delay. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-239...
Page 454: Ground Current
Figure 5-124: Wattmetric zero-sequence directional logic 5.7.7 Ground current 5.7.7.1 Menu SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  GROUND CURRENT  GROUND CURRENT  GROUND TOC1 See below     5-240 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 455 — This setting selects the signal source for the ground time overcurrent protection element. GROUND TOC1 SIGNAL SOURCE — This setting selects how ground current input quantities are interpreted by the F60. Inputs can be GROUND TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 456 GROUND IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 0.00 s GROUND IOC1 BLOCK: Range: FlexLogic operand  GROUND IOC1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset 5-242 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 457 The resultant primary current is negligible for faults on the lower 30% of the winding F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-243...
Page 458 This is similar to a single infeed situation and can be mistaken for an internal fault. Similar difficulties occur in a breaker-and-a-half application of the restricted ground fault, where any through fault with a weak infeed from the winding itself can cause problems. 5-244 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 459 (Igr(k)) does not reduce instantly but keeps decaying decreasing its value by 50% each 15.5 power system cycles. Having the differential and restraining signals developed, the element applies a single slope differential characteristic with a minimum pickup as shown in the following logic diagram. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-245...
Page 460 Given the following inputs: IA = 1.10 pu ∠0°, IB = 1.0 pu ∠–120°, IC = 1.0 pu ∠120°, and IG = 0.05 pu ∠0° The relay calculates the following values: I_0 = 0.033 pu ∠0°, I_2 = 0.033 pu ∠0°, and I_1 = 1.033 pu ∠0° 5-246 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 461: Negative Sequence Current
 NEG SEQ DIR OC2   The F60 provides two negative-sequence time overcurrent elements, two negative-sequence instantaneous overcurrent elements, and two negative-sequence directional overcurrent elements. For information on the negative sequence time overcurrent curves, see the Inverse TOC Curve Characteristics section earlier.
Page 462 NEG SEQ IOC1 Range: 0.020 to 30.000 pu in steps of 0.001  PICKUP: 1.000 pu NEG SEQ IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 0.00 s 5-248 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 463 SOURCE: SRC 1 NEG SEQ DIR OC1 Range: 0.00 to 250.00 ohms in steps of 0.01  OFFSET: 0.00 Ω NEG SEQ DIR OC1 Range: Neg Sequence, Zero Sequence  TYPE: Neg Sequence F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-249...
Page 464 CT errors, since the current is low. The operating quantity depends on the way the test currents are injected into the F60. For single phase injection •...
Page 465 The reverse-looking function is faster compared to the forward-looking function, so use the reverse-looking function for the blocking direction. This allows for better protection coordination. Take this bias F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-251...
Page 466 NEG SEQ DIR OC1 REV PICKUP threshold applies to zero-sequence or negative-sequence current based on the setting. When NEG SEQ DIR OC1 TYPE selecting this setting, keep in mind that the design uses a positive-sequence restraint technique. 5-252 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 467: Breaker Failure (Ansi 50Bf)
Range: 0.020 to 30.000 pu in steps of 0.001  PICKUP: 1.050 pu BF1 N AMP SUPV Range: 0.020 to 30.000 pu in steps of 0.001  PICKUP: 1.050 pu BF1 USE TIMER 1: Range: Yes, No  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-253...
Page 468 Valid only for 1-Pole breaker failure schemes φ BF1 BKR POS2 Range: FlexLogic operand  Valid only for 1-Pole breaker failure schemes φ BF1 BKR POS2 Range: FlexLogic operand  Valid only for 1-Pole breaker failure schemes 5-254 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 469 There is no current level check in this logic as it is intended to detect low magnitude faults and it is therefore the slowest to operate. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-255...
Page 470 — This setting is used to select the breaker failure operating mode: single or three pole. BF1 MODE — If set to "Yes," the element is initiated if current flowing through the breaker is above the supervision BF1 USE AMP SUPV pickup level. 5-256 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 471 In microprocessor relays this time is not significant. In F60 relays, which use a Fourier transform, the calculated current magnitude ramps-down to zero one power frequency cycle after the current is interrupted, and this lag needs to be included in the overall margin duration, as it occurs after current interruption.
Page 472 Upon operation of the breaker failure element for a single pole trip command, a three-pole trip command needs to be given via output operand BKR FAIL 1 TRIP 5-258 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 473 CHAPTER 5: SETTINGS GROUPED ELEMENTS Figure 5-136: Single-pole breaker failure initiate logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-259...
Page 474 GROUPED ELEMENTS CHAPTER 5: SETTINGS Figure 5-137: Single-pole breaker failure, timers logic 5-260 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 475 CHAPTER 5: SETTINGS GROUPED ELEMENTS Figure 5-138: Three-pole breaker failure, initiate logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-261...
Page 476 GROUPED ELEMENTS CHAPTER 5: SETTINGS Figure 5-139: Three-pole breaker failure, timers logic 5-262 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 477: Voltage Elements
The time delay is adjustable from 0 to 600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay characteristic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-263...
Page 478 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s PHASE UV1 MINIMUM Range: 0.000 to 3.000 pu in steps of 0.001  VOLTAGE: 0.100 pu PHASE UV1 BLOCK: Range: FlexLogic operand  5-264 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 479 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s PHASE OV1 BLOCK: Range: FlexLogic Operand  PHASE OV1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset PHASE OV1 Range: Disabled, Enabled  EVENTS: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-265...
Page 480 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s NEUTRAL OV1 BLOCK: Range: FlexLogic operand  NEUTRAL OV1 TARGET: Range: Self-reset, Latched, Disabled  Self-reset NEUTRAL OV1 EVENTS: Range: Disabled, Enabled  Disabled 5-266 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 481 There are three negative-sequence overvoltage elements available. Use the negative-sequence overvoltage element to detect loss of one or two phases of the source, a reversed phase sequence of voltage, or a non-symmetrical system voltage condition. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-267...
Page 482 Range: Disabled, Enabled  Disabled The F60 contains one auxiliary undervoltage element for each VT bank. This element monitors undervoltage conditions of the auxiliary voltage. selects the voltage level at which the time undervoltage element starts timing. The nominal secondary...
Page 483 Range: Disabled, Enabled  Disabled The F60 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM is the per-unit (pu) base used when setting the SETUP ...
Page 484: Sensitive Directional Power (Ansi 32)
The element has an adjustable characteristic angle and minimum operating power as shown in the Directional Power Characteristic diagram that follows. The element responds to the following condition: P cos θ + Q sin θ > SMIN Eq. 5-30 where 5-270 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 485 For example, section (a) in the figure shows settings for reverse power, while section (b) shows settings for low forward power applications. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-271...
Page 486 DIR POWER 1 RCA setting to “90°,” active underpower by setting to “180°,” and reactive underpower by DIR POWER 1 RCA DIR POWER 1 RCA setting to “270°.” DIR POWER 1 RCA 5-272 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 487: Control Elements
5.8.2 Trip bus SETTINGS  CONTROL ELEMENTS  TRIP BUS  TRIP BUS 1(6)  TRIP BUS 1 TRIP BUS 1 Range: Enabled, Disabled  FUNCTION: Disabled  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-273...
Page 488 — The trip bus output is blocked when the operand assigned to this setting is asserted. TRIP BUS 1 BLOCK — This setting specifies a time delay to produce an output depending on how output is used. TRIP BUS 1 PICKUP DELAY 5-274 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 489: Setting Groups
Range: FlexLogic operand   GROUP 6 ACTIVATE ON: Range: FlexLogic operand  GROUP 1 NAME: Range: up to 16 alphanumeric characters   GROUP 6 NAME: Range: up to 16 alphanumeric characters  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-275...
Page 490 The most recent SelectActiveSG selection is preserved while the UR is powered down or reset. If it becomes necessary to cancel the SelectActiveSG selection without using a SelectActiveSG service request, change the setting to Disabled. This resets the SelectActiveSG selection to 1. SETTING GROUPS FUNCTION 5-276 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 491: Selector Switch
1 to the . If the control word is outside the range, an alarm is established by setting the SELECTOR FULL RANGE FlexLogic operand for three seconds. SELECTOR ALARM F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-277...
Page 492 If the acknowledging signal does not appear within a pre-defined period of time, the selector rejects the change and an alarm established by invoking the FlexLogic operand SELECTOR BIT ALARM for three seconds. 5-278 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 493 The selector position pre-selected via the three-bit control input has not been confirmed before the time The following figures illustrate the operation of the selector switch. In these diagrams, “T” represents a time-out setting. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-279...
Page 494 CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-153: Time-out mode 5-280 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 495 1 through 3. The pre-selected setting group is to be applied automatically after five seconds of inactivity of the control inputs. When the relay powers up, it is to synchronize the setting group to the three-bit control input. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-281...
Page 496 SETTINGS  PRODUCT menu: SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 : “Self-reset” PUSHBUTTON 1 FUNCTION : “0.10 s” PUSHBUTTON 1 DROP-OUT TIME The figure shows the logic for the selector switch. 5-282 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 497: Underfrequency (Ansi 81U)
 DELAY : 2.000 s UNDERFREQ 1 TARGET: Range: Self-reset, Latched, Disabled  Self-reset UNDERFREQ 1 EVENTS: Range: Disabled, Enabled  Disabled There are six identical underfrequency elements, numbered 1 through 6. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-283...
Page 498: Overfrequency (Ansi 81O)
The channels are searched for the signal input in the following order: voltage channel A, auxiliary voltage channel, current channel A, and ground current channel. The first available signal is used for frequency calculation. 5-284 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 499: Frequency Rate Of Change (Ansi 81R)
Range: 0 to 65.535 s in steps of 0.001  DELAY: 0.000 s FREQ RATE 1 RESET Range: 0 to 65.535 s in steps of 0.001  DELAY: 0.000 s FREQ RATE 1 BLOCK: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-285...
Page 500 If the signal source assigned to the frequency rate of change element is only set to auxiliary VT, then the minimum voltage supervision is 3 V. Figure 5-158: Frequency rate of change logic 5-286 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 501: Synchrocheck (Ansi 25)
The synchronism check function supervises the paralleling of two parts of a system that are to be joined by the closure of a circuit breaker. The synchrocheck elements are typically used at locations where the two parts of the system are interconnected through at least one other point in the system. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-287...
Page 502 Figure 5-159: Synchrocheck plot for slip > 0 (slip = F2-F1) 5-288 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 503 The selected sources for synchrocheck inputs V1 and V2 (which must not be the same source) can include both a three-phase and an auxiliary voltage. The relay automatically selects the specific voltages to be used by the synchrocheck element in accordance with the following table. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-289...
Page 504 The relay uses the phase channel of a three-phase set of voltages if programmed as part of that source. The relay uses the auxiliary voltage channel only if that channel is programmed as part of the Source and a three-phase set is not. 5-290 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 505 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-161: Synchrocheck logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-291...
Page 506: Autoreclose (Ansi 79)
Range: FlexLogic operand  AR1 DELAY 2: Range: 0.00 to 655.35 s in steps of 0.01  0.000 s AR1 RESET LOCKOUT Range: 0.00 to 655.35 s in steps of 0.01  DELAY: 60.000 5-292 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 507  Disabled The F60 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. The maximum number of autoreclosure elements available is equal to the number of installed CT banks.
Page 508 "reclose-in-progress" state. If all conditions allowing a breaker closure are not satisfied when this time expires, the scheme goes to Lockout. This timer must be set to a delay less than the reset timer. 5-294 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 509 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-162: Autoreclosure logic (Sheet 1 of 2) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-295...
Page 510 CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-163: Autorecloser logic (Sheet 2 of 2) 5-296 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 511 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-164: Single shot autoreclosing sequence - permanent fault F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-297...
Page 512: Digital Elements
DIGITAL ELEMENT 1 RESET DELAY — This setting enables or disabled the digital element pickup LED. When set to “Disabled,” the DIGITAL ELEMENT 1 PICKUP LED operation of the pickup LED is blocked. 5-298 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 513 In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact that is open when the breaker is open (see figure). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must include the breaker position. Figure 5-166: Trip circuit example 1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-299...
Page 514 In this case, it is not required to supervise the monitoring circuit with the breaker position – the setting is BLOCK selected to “Off.” In this case, the settings are as follows (EnerVista example shown). 5-300 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 515: Digital Counters
COUNTER 1 BLOCK: Range: FlexLogic operand  CNT1 SET TO PRESET: Range: FlexLogic operand  COUNTER 1 RESET: Range: FlexLogic operand  COUNT1 FREEZE/RESET: Range: FlexLogic operand  COUNT1 FREEZE/COUNT: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-301...
Page 516 If control power is interrupted, the accumulated and frozen values are saved into non-volatile memory during the power-down operation. 5-302 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 517: Monitoring Elements
 BREAKER   FLASHOVER 2  BREAKER RESTRIKE 1 See page 5-318     BREAKER RESTRIKE 3    CT FAILURE See page 5-320   DETECTOR 1  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-303...
Page 518 THRESHOLD: 15% HI-Z 3-PHASE EVENT Range: 1 to 1000 A in steps of 1  THRESHOLD: 25 A HI-Z VOLTAGE SUPV Range: 0 (off) to 100% in steps of 1  THRESHOLD: 5% 5-304 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 519 Flag indicating an instantaneous 2-cycle overcurrent was detected LossOfLoad Flag indicating a loss of load was detected EadZeroed Flag indicating that this phase’s EAD table was cleared HighZArmed Flag indicating that this phase is armed for a high-Z detection F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-305...
Page 520 “Normal”. Also, if two minutes pass without high levels from the Expert Arc Detector Algorithm while the algorithm is in its Armed state, then it moves from the “Armed” state directly back to the “Normal” state. 5-306 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 521 It is recommended that this setting is above the maximum 3Io (residual) current due to unbalanced loading. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-307...
Page 522 For the first three to five days after installation (or after being out-of-service for a significant period), the F60 can identify some of this noise as arcing. Take this into account when responding to alarms during these operating periods.
Page 523 5.9.0.3 Breaker arcing current SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BREAKER 1(4) ARCING CURRENT  BREAKER 1 BKR 1 ARC AMP Range: Disabled, Enabled   ARCING CURRENT FUNCTION: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-309...
Page 524 (breaker operating time), clear ARCING AMPS (kA -cycle) and AMP MAX (kA) values of the last event. — This setting specifies the maximum symmetrical interruption rating of the circuit breaker. BKR 1 INTERUPTION RATING 5-310 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 525 CHAPTER 5: SETTINGS MONITORING ELEMENTS Figure 5-170: Arcing current measurement F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-311...
Page 526 MONITORING ELEMENTS CHAPTER 5: SETTINGS Figure 5-171: Breaker arcing current logic 5-312 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 527 (contact input indicating the breaker status is off), and no flashover current is flowing. A contact showing the breaker status must be provided to the relay. The voltage difference is not considered as a condition for open breaker in this part of the logic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-313...
Page 528 This application does not require detection of breaker status via a 52a contact, as it uses a voltage difference larger than setting. However, monitoring the breaker contact ensures scheme stability. BRK 1 FLSHOVR DIFF V PKP 5-314 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 529 (all line breakers open), to well above the maximum line (feeder) load (line/feeder connected to load). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-315...
Page 530 A six-cycle time delay applies after the selected FlexLogic operand resets. — This setting specifies the time delay to operate after a pickup condition is detected. BRK FLSHOVR PKP DELAY 5-316 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 531 CHAPTER 5: SETTINGS MONITORING ELEMENTS Figure 5-172: Breaker flashover logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-317...
Page 532  EVENTS: Disabled One breaker restrike element is provided for each DSP in the F60. According to IEEE standard C37.100 entitled IEEE Standard Definitions for Power Switchgear, restrike is defined as “a resumption of current between the contacts of a switching device during an opening operation after an interval of zero current of ¼...
Page 533 — Specifies the reset delay for this element. When set to “0 ms,” then FlexLogic operand is BREAKER RESTRIKE 1 RESET DELAY picked up for only 1/8th of the power cycle. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-319...
Page 534 CT FAIL 1 3V0 INPUT Range: 0.04 to 2.00 pu in steps of 0.01  PKP: 0.20 pu CT FAIL 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001  DELAY: 1.000 s 5-320 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 535 CT FAIL 1 3V0 INPUT — Specifies the pickup value for the 3V_0 source. CT FAIL 1 3V0 INPUT PICKUP — Specifies the pickup delay of the CT failure element. CT FAIL 1 PICKUP DELAY F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-321...
Page 536 RESET DELAY: 0.100 s INCIPIENT FAULT 1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset INCIPIENT FAULT 1 Range: Disabled, Enabled  EVENTS: Disabled There are two incipient cable fault detection elements in the relay. 5-322 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 537 — Selects a current source for the incipient cable fault detector element. This source must be INCIPIENT FAULT 1 SOURCE assigned a valid CT bank. — Specifies the pickup level of the overcurrent detector in per-unit values of the CT nominal INCIPIENT FAULT 1 PICKUP current. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-323...
Page 538 B failures is when positive sequence current is present and there is an insignificant amount of positive sequence voltage. Also, a rapid decrease in the phase voltages magnitude from a healthy 5-324 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 539 PHASE VT SECONDARY PHASE VT SECONDARY of DELTA VTs. The setting is found under SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK  PHASE VT SECONDARY Figure 5-179: VT fuse fail logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-325...
Page 540 I = measured overload RMS current = measured load RMS current before overload occurs k = IEC 255-8 k-factor applied to I , defining maximum permissible current above nominal current = protected element base (nominal) current 5-326 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 541 The reset time of the thermal overload protection element is also time delayed using following formula: Eq. 5-34 where τ = thermal protection trip time constant = a minimum reset time setting Figure 5-180: IEC 255-8 sample operate and reset curves F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-327...
Page 542 20 minutes Air-core reactor 40 minutes 30 minutes Busbar 60 minutes 20 minutes Underground cable 20 to 60 minutes 60 minutes The figure shows the logic for the thermal overload protection element. 5-328 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 543 It also monitors changes in the I_2 / I_1 ratio, I_1 minimum, and I_1 maximum. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-329...
Page 544 — This setting specifies the pickup time delay for this function to operate after assertion BROKEN CONDUCTOR 1 PKP DELAY of the broken conductor pickup FlexLogic operand. 5-330 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 545 CHAPTER 5: SETTINGS MONITORING ELEMENTS Figure 5-182: Broken conductor detection logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-331...
Page 546: Cold Load Pickup
The reset delay interval is intended to be set to a ON-LOAD TIME BEFORE RESET period until the feeder load has decayed to normal levels, after which other features can be used to switch setting groups. 5-332 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 547: Pilot Schemes
 DELAY: 0.090 s ECHO DURATION: Range: 0.000 to 65.535 s in steps of 0.001  0.100 s ECHO LOCKOUT: Range: 0.000 to 65.535 s in steps of 0.001  0.250 s F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-333...
Page 548 — This setting allows the user to select the FlexLogic operand to represent the Line End Open POTT3 LINE END OPEN condition, such as breaker open status, or under voltage and under current conditions. 5-334 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 549 Figure 5-185: POTT3 scheme logic 5.9.2.2 Directional comparison blocking 3 (DCB3) SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  DCB3 SCHEME  BLOCKING3 SCHEME DCB3 SCHEME Range: Disabled, Enabled  FUNCTION: Disabled  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-335...
Page 550 If the reverse fault condition prevails for , the blocking operation is extended by the TRANS BLOCK PICKUP DELAY transient blocking timer for . This allows riding through current reversal conditions. However, if TRANS BLOCK RESET DELAY 5-336 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 551 FORCE TX STOP. — This setting selects the FlexLogic operands to represent the receive signals for the scheme. Contact inputs DCB3 RX interfacing with a signaling system(s) are used typically. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-337...
Page 552: Inputs/Outputs
Range: 0.0 to 16.0 ms in steps of 0.5  DEBNCE TIME: 6.0 ms CONTACT INPUT H5a Range: Disabled, Enabled  EVENTS: Disabled ↓  CONTACT INPUT xxx    CONTACT INPUT   THRESHOLDS 5-338 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 553 The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user-settable debounce time in order for the F60 to validate the new contact state. In the following figure, the debounce time is set at 2.5 ms;...
Page 554: Virtual Inputs
The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include signals generated by the local user interface. The virtual outputs are outputs of FlexLogic equations used to customize the device. Virtual outputs can also serve as virtual inputs to FlexLogic equations. 5-340 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 555: Contact Outputs
(virtual output, element state, contact input, or virtual input). An additional FlexLogic operand can be used to SEAL-IN the relay. Any change of state of a contact output can be logged as an Event if programmed to do so. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-341...
Page 556 If any latching outputs exhibits a discrepancy, the LATCHING OUTPUT ERROR self-test error is declared. The error is signaled by the FlexLogic operand, event, and target message. LATCHING OUT ERROR 5-342 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 557 (assuming an H4L module): OUTPUTS  CONTACT OUTPUT H1a CONTACT OUTPUT H1c : “VO1” OUTPUT H1a OPERATE : “VO2” OUTPUT H1a RESET : “VO2” OUTPUT H1c OPERATE : “VO1” OUTPUT H1c RESET F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-343...
Page 558 Program the Latching Outputs by making the following changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT menu (assuming an H4L module): OUTPUTS  CONTACT OUTPUT H1a : “VO1” OUTPUT H1a OPERATE : “VO2” OUTPUT H1a RESET 5-344 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 559: Virtual Outputs
• To acknowledge/reset a specific annunciator window, use the Up, Down, Left and Right pushbuttons to select the window, and press the RESET or ENTER pushbutton F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-345...
Page 560: Direct Inputs And Outputs
SETTINGS  INPUTS/OUTPUTS  DIRECT OUTPUTS  DIRECT OUTPUT 1(32)  DIRECT OUTPUT 1 DIRECT OUT 1 NAME: Range: up to 12 alphanumeric characters   Dir Out 1 DIRECT OUT 1 OPERAND: Range: FlexLogic operand  5-346 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 561 A simple interlocking busbar protection scheme can be accomplished by sending a blocking signal from downstream devices, say 2, 3 and 4, to the upstream device that monitors a single incomer of the busbar, as shown in the figure. Figure 5-192: Sample interlocking busbar protection scheme F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-347...
Page 562 Figure 5-193: Three-terminal line application Assume the Hybrid Permissive Overreaching Transfer Trip (Hybrid POTT) scheme is applied using the architecture shown as follows. The scheme output operand is used to key the permission. HYB POTT TX1 5-348 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 563 "DIRECT INPUT 6" (forward a message from 3 to 1) DIRECT OUT 4 OPERAND The figure shows the signal flow among the three IEDs. Figure 5-195: Signal flow for direct input and output F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-349...
Page 564: Teleprotection
As the following figure demonstrates, processing of the teleprotection inputs/outputs is dependent on the number of communication channels and terminals. On two-terminal two-channel systems, they are processed continuously on each channel and mapped separately per channel. Therefore, to achieve redundancy, the user must assign the same operand 5-350 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 565: Transducer Inputs/Outputs
 VALUE: 0.000 The F60 is provided with optional DCmA capability. This feature is specified as an option at the time of ordering. See the Order Codes section in chapter 2 for details. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 566: Rtd Inputs
An alphanumeric ID is assigned to the channel; this ID is included in the channel actual values. It is also used to reference the channel as the input parameter to features designed to measure this type of parameter. Selecting the type of RTD connected to the channel configures the channel. 5-352 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 567: Dcma Outputs
Range: Off, any analog actual value parameter   SOURCE: Off DCMA OUTPUT H1 Range: –1 to 1 mA, 0 to 1 mA, 4 to 20 mA  RANGE: –1 to 1 mA F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-353...
Page 568 MAX VAL MIN VAL MAX VAL – < 0.1 pu. The resulting characteristic is illustrated in the following figure. MIN VAL Figure 5-197: DCmA output characteristic Settings 5-354 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 569 ±1% of reading error for the active power at power factor of 0.9 For example at the reading of 20 MW, the worst-case error is 0.01 × 20 MW + 0.207 MW = 0.407 MW. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-355...
Page 570 6), while at the same time the VT nominal voltage is 1 pu for the settings. Consequently the settings required in this example differ from naturally expected by the factor of The worst-case error for this application could be calculated by superimposing the following two sources of error: 5-356 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 571: Testing
 FUNCTION: Disabled The F60 provides a test facility to verify the functionality of contact inputs and outputs, some communication functions and the phasor measurement unit (where applicable), using simulated conditions. The test mode can be in any of three states: Disabled, Isolated, or Forcible.
Page 572: Test Mode Forcing
  When in Forcible mode, the operand selected by the setting dictates further response of the F60 to TEST MODE FORCING testing conditions, as described in the following two sections. The test mode state is indicated on the relay front panel by a combination of the Test Mode LED indicator, the In-Service LED indicator, and by the critical fail relay, as shown in the following table.
Page 573: Force Contact Inputs
If set to “Closed,” the input is forced to report as closed (Logic 1) while the operand selected by TEST MODE FORCING setting is On regardless of the voltage across the input terminals. While the selected operand is Off, the input behaves as it does when in service. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-359...
Page 574: Force Contact Outputs
While the selected operand is Off, the output behaves as it does when in service. On restart, the setting and the force contact input and force contact output settings revert to TEST MODE FORCING their default states. 5-360 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 575: Actual Values
   AUTORECLOSE See page 6-7    RxGOOSE STATUS See page 6-6    RxGOOSE See page 6-6   STATISTICS  DIGITAL COUNTERS See page 6-7   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 576  OF CHANGE  FLEXELEMENTS See page 6-24    RxGOOSE Analogs See page 6-25    WATTMETRIC See page 6-25   GROUND FAULT 1  WATTMETRIC   GROUND FAULT 2 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 577: Front Panel
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel. The feature applies to the enhanced and standard front panels. To view the front panel in EnerVista software: Click Actual Values > Front Panel. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 578: Status
The present status of the 64 virtual inputs is shown here. The first line of a message display indicates the ID of the virtual input. For example, ‘Virt Ip 1’ refers to the virtual input in terms of the default name. The second line of the display indicates the logic state of the virtual input. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 579: Rxgoose Boolean Inputs
Range: On, Off  STATUS: Off The F60 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. 6.3.4 RxGOOSE DPS inputs ACTUAL VALUES ...
Page 580: Virtual Outputs
 Offline The F60 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. actual value does not consider RxGOOSE that are not configured or are not used by any RxGOOSE All RxGOOSE Online Input.
Page 581: Autoreclose
CHAPTER 6: ACTUAL VALUES STATUS The F60 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. — State number. The most recently received value in GOOSE message field stNum. The publisher increments stNum stNum each time that the state of one or more of the GOOSE message members is sent with a revised value.
Page 582: Flex States
RTC, considering the quality information imbedded in the ACCURACY received time signal. The value 999,999,999 indicates that the magnitude of the estimated error is one second or more, or that the error cannot be estimated. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 583: Hi-Z Status
CRC check. High values for either of these counts can indicate on a problem with wiring, the communication channel, or one or more relays. The UNRETURNED MSG COUNT CRC FAIL values can be cleared using the command. COUNT CLEAR DIRECT I/O COUNTERS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 584: Direct Devices Status
CHANNEL 2 LOST Range: 1 to 65535 in steps of 1  PACKETS: VALIDITY OF CHANNEL Range: n/a, FAIL, OK  CONFIGURATION: FAIL The status information for two channels is shown here. 6-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 585: Incipient Fault Detector
UR over Ethernet, the Modbus TCP status shows 3. If the EnerVista application is closed, the Modbus TCP status shows 4. For the graphical front panel, the remaining connections refer to TCP connections only. — The number of IEC 61850 connections remaining. MMS TCP F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-11...
Page 586: Parallel Redundancy Protocol (Prp)
Range: 0 to 4G, blank if PRP disabled  The F60 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 587: Metering
GOOSE or for R-GOOSE when setting R-TxGOOSE1 DST IP is multicast. 6.4 Metering 6.4.1 Metering conventions 6.4.1.1 UR convention for measuring power and energy The figure illustrates the conventions established for use in UR devices. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-13...
Page 588 6.4.1.2 UR convention for measuring phase angles All phasors calculated by URs and used for protection, control and metering functions are rotating phasors that maintain the correct phase angle relationships with each other at all times. 6-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 589 For display and oscillography purposes the phase angles of symmetrical components are referenced to a common reference as described in the previous sub-section. WYE-connected instrument transformers • ABC phase rotation: • ACB phase rotation: The above equations apply to currents as well. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-15...
Page 590 * The power system voltages are phase-referenced – for simplicity – to V and V , respectively. This, however, is a relative matter. It is important to remember that the F60 displays are always referenced as specified under SETTINGS  SYSTEM SETUP  POWER SYSTEM  FREQUENCY AND PHASE REFERENCE The example above is illustrated in the following figure.
Page 591: Sources
0.000 A SRC 1 RMS In:  0.000 A SRC 1 PHASOR Ia:  0.000 A 0.0° SRC 1 PHASOR Ib:  0.000 A 0.0° SRC 1 PHASOR Ic:  0.000 A 0.0° F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-17...
Page 592 0.00 V SRC 1 RMS Vbc:  0.00 V SRC 1 RMS Vca:  0.00 V SRC 1 PHASOR Vab:  0.000 V 0.0° SRC 1 PHASOR Vbc:  0.000 V 0.0° 6-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 593 SRC 1 APPARENT PWR  3φ: 0.000 VA SRC 1 APPARENT PWR  φa: 0.000 VA SRC 1 APPARENT PWR  φb: 0.000 VA SRC 1 APPARENT PWR  φc: 0.000 VA F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-19...
Page 594 S = V x Î x Î x Î Eq. 6-1 When VTs are configured in delta, the F60 does not calculate power in each phase and three-phase power is measured as S = V x Î x Î Eq. 6-2...
Page 595 The signal used for frequency estimation is low-pass filtered. The final SYSTEM SETUP  POWER SYSTEM frequency measurement is passed through a validation filter that eliminates false readings due to signal distortions and transients. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-21...
Page 596 The harmonics are a percentage of the fundamental signal obtained as a ratio of harmonic amplitude to fundamental amplitude multiplied by 100%. The total harmonic distortion (THD) is the ratio of the total harmonic content to the fundamental: Eq. 6-4 6-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 597: Sensitive Directional Power
CHAPTER 6: ACTUAL VALUES METERING Voltage harmonics are not available on F60 relays configured with the high-impedance fault detection (Hi-Z) feature. Voltage harmonics are calculated only for Wye connected phase VTs. Ensure that the SYSTEM SETUP  AC INPUTS setting is “Wye” to enable voltage harmonics metering.
Page 598: Tracking Frequency
= maximum nominal primary RMS value of the +IN and –IN inputs BASE SYNCHROCHECK = maximum primary RMS value of all the sources related to the +IN and –IN inputs BASE (Max Delta Volts) 6-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 599: Rxgoose Analogs
 0.000 The F60 is provided with optional GOOSE communications capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. The RxGOOSE Analog values display in this menu. The RxGOOSE Analog values are received via IEC 61850 GOOSE messages sent from other devices.
Page 600: Pmu Aggregator
 -50 °C  Actual values for each RTD input channel that is enabled are displayed with the top line as the programmed channel ID and the bottom line as the value. 6-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 601: Records
  Date and time stamps EVENT: 3 EVENT 3    POWER ON DATE: 2000/07/14 EVENT: 2 EVENT 3   POWER OFF TIME: 14:53:00.03405 EVENT: 1  EVENTS CLEARED F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-27...
Page 602 (highlight in yellow), then press the green or cyan Mark Event Tab pushbutton. The mark color hides the selector until the selector is moved. A field at the top of the page shows the interval between the two marks. 6-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 603: Oscillography
It counts up at the defined sampling NEWEST SAMPLE TIME rate. If the data logger channels are defined, then both values are static. See the menu for clearing data logger records. COMMANDS  CLEAR RECORDS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-29...
Page 604: Phasor Measurement Unit Records
BKR 1 ARCING AMP φC:  0.00 kA2-cyc BKR 1 AMP MAX φA:  0.00 kA BKR 1 AMP MAX φB:  0.00 kA BKR 1 AMP MAX φC:  0.00 kA 6-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 605: Product Information
ORDER CODE LINE 2: Range: up to 20 alphanumeric characters  A0A-A0A-A0A ORDER CODE LINE 3: Range: up to 20 alphanumeric characters  ORDER CODE LINE 4: Range: up to 20 alphanumeric characters  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-31...
Page 606: Firmware Revisions
6.6.2.2 Graphical front panel ACTUAL VALUES  PRODUCT INFO  FIRMWARE REVISIONS  FIRMWARE REVISIONS F60 Relay Range: 0.00 to 655.35  REVISION: 7.6x Revision number of the application firmware.  6-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 607 The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been installed. The date format reflects the format specified for the clock and can vary from that shown here. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-33...
Page 608 PRODUCT INFORMATION CHAPTER 6: ACTUAL VALUES 6-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 609: Commands And Targets
The commands menu contains relay directives intended for operations personnel. All commands can be protected from unauthorized access via the command password; see the Security section of chapter 5 for details. The following flash message appears after successfully command entry. COMMAND EXECUTED F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 610: Virtual Inputs
Range: No, Yes  CHANGE COUNTER? No CLEAR TELEPROTECT Range: No, Yes  COUNTERS? No CLEAR INCIPIENT Range: No, Yes  FAULT COUNTERS? No  CLEAR IEC61850 See below   XWSI OPCNT F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 611: Set Date And Time
Range: No, Yes   RELAY MAINTENANCE PERFORM LCD TEST? Range: Off, Red, Green, Blue, White & Text Pattern,  Black & Text Pattern, TV Test Pattern PERFORM PUSHBUTTON Range: No, Yes  TEST? No F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 612 Although the diagnostic information is cleared before the F60 is shipped from the factory, the user can want to clear the diagnostic information for themselves under certain circumstances. For example, you clear diagnostic information after replacement of hardware. Once the diagnostic information is cleared, all self-checking variables are reset to their initial state and diagnostics restart from scratch.
Page 613: Phasor Measurement Unit One-Shot
30 seconds afterwards PMU ONE-SHOT OP When the function is disabled, all three operands are de-asserted. The one-shot function applies to all logical PMUs of a given F60 relay. Figure 7-1: PMU one-shot FlexLogic operands F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 614: Security
With the CyberSentry option, this setting is available to enable or disable the following commands. — Selecting ‘Yes’ allows the Supervisor to forcefully logoff an administrator session. ADMINISTRATOR LOGOFF — Selecting ‘Yes’ allows the Supervisor to forcefully logoff an engineer session. ENGINEER LOGOFF F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 615: Targets Menu
A target enables the EnerVista UR Setup software to monitor automatically and display the status of any active target messages of all the devices inserted into that site. Each F60 element with a TARGET setting has a target message that when activated by its element is displayed in sequence with any other currently active target messages in the menu.
Page 616: Relay Self-Tests
Contact Factory (xxx) • Latched target message: Yes. • Description of problem: One or more installed hardware modules is not compatible with the F60 order code. • How often the test is performed: Module dependent. • What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed module (for example, F8L).
Page 617 MAINTENANCE ALERT: Direct I/O Ring Break • Latched target message: No. • Description of problem: Direct input and output settings are configured for a ring, but the connection is not in a ring. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 618 Latched target message: No. • Description of problem: A data item in a configurable GOOSE data set is oscillating. • How often the test is performed: Upon scanning of each configurable GOOSE data set. 7-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 619 This time can be from milliseconds to minutes. • What to do: Check GOOSE setup. AGGREGATOR ERROR: • Latched target message: No. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 7-11...
Page 620 V-type CPU = All ports support RJ45 SFPs only The consequence of an incorrect SFP can range from damage to the F60 to no power information for the F60 on its web page (enter IP address in a web browser, then click the SFP Transceiver Information. Only the type of SFP displays and not power data).
Page 621 How often the test is performed: On relay power-up and afterwards once every 24 hours. • What to do: Contact the factory. PROTOTYPE FIRMWARE: Self Test Error • Description of problem: Seen until the builds is tagged as being 'release candidate' or 'gold' builds. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 7-13...
Page 622 Brick. Where multiple UR-series devices have self-test errors, look for common causes. 7-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 623 Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the front panel reset key if the command has ended, however the output can still be non-functional. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 7-15...
Page 624 TARGETS MENU CHAPTER 7: COMMANDS AND TARGETS 7-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 625: Commissioning
Injection to a particular F60 frequency element must be to its configured source and to the channels that the source uses for frequency measurement. For frequency measurement, a source uses the first quantity configured in the following...
Page 626 0.20 Hz before the threshold and subtract 1 second from the test set time reading of ramp start to relay operation. Note that the F60 event records only show the “pickup delay” component, a definite time timer. This is exclusive of the time taken by the frequency responding component to pickup.
Page 627: Theory Of Operation
LEDs are activated on the relay faceplate. The detection of a downed conductor or arcing condition is accomplished through the following algorithms: • Energy algorithm • Randomness algorithm • Expert Arc Detector algorithm F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 628: Energy Algorithm
These increases in confidence levels occur because multiple, consecutive indications from a given algorithm and indications from multiple independent algorithms are more indicative of the presence of arcing than a single algorithm giving a single indication. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 629: Spectral Analysis Algorithm
This information is then provided as input to the Arc Burst Pattern Analysis algorithm. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 630: Arc Burst Pattern Analysis Algorithm
The single-ended fault location method assumes that the fault components of the currents supplied from the local (A) and remote (B) systems are in phase. The figure shows an equivalent system for fault location. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 631 Depending on the fault type, appropriate voltage and current signals are selected from the phase quantities before applying the preceding equation (the superscripts denote phases, the subscripts denote stations). For AG faults: Eq. 9-5 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 632 If the VTs are connected in a delta configuration, fault location is performed based on the delta voltages and zero-sequence voltage approximated based on the zero-sequence current: Eq. 9-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 633 CHAPTER 9: THEORY OF OPERATION FAULT LOCATOR where Z is the equivalent zero-sequence impedance behind the relay as entered under the fault report setting menu. SYS0 Figure 9-2: Fault locator scheme F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 634 FAULT LOCATOR CHAPTER 9: THEORY OF OPERATION F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 635: Maintenance
UR Family Communications Guide for the entries. The upper part of the window displays values. The lower part of the window is for factory service use. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-1...
Page 636 Float — A numbering system with no fixed number of digits before or after the decimal point. An example is 0.000000. Binary — A numbering system using 0 and 1. An example is 0000-0000-0000-0000. Entries are not saved when closing the window. 10-2 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 637: General Maintenance
GENERAL MAINTENANCE 10.2 General maintenance The F60 requires minimal maintenance. As a microprocessor-based relay, its characteristics do not change over time. Expected service life is 20 years for UR devices manufactured June 2014 or later when applied in a controlled indoor environment and electrical conditions within specification.
Page 638 Using the Up or Down pushbuttons on the front panel, select the file. Press the COPY pushbutton. The files are copied from the F60 to the USB drive. Do not unplug the USB drive while copying is in progress, else the USB drive can be compromised.
Page 639: Convert Device Settings
Convert the settings by right-clicking one of the files in the Offline Window and selecting the Convert Device Settings option. GE recommends converting settings in firmware steps, for example when converting from 6.0 to 7.4x, convert first to 7.0 then 7.4 in order to follow embedded conversion rules and keep settings.
Page 640 Change settings in the new file, for example by looking at the original file. Write the converted file to the device, for example by dragging and dropping from the Offline Window to the Online Window. Check settings and operation. 10-6 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 641: Copy Settings To Other Device
10.5 Copy settings to other device Settings from one F60 device can be copied to another F60 device for rapid deployment. The order codes must match. See the Settings File section at the beginning of the Interfaces chapter for a list of settings not deployed, such as IP address.
Page 642: Back Up And Restore Settings
UR device settings can be saved in a backup URS file using the EnerVista UR Setup software. The URS file is the standard UR settings file. For an introduction to settings files in the URS format, see the beginning of the Interfaces chapter. 10-8 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 643 Have this option enabled when you want to keep the IID file from the UR device instead of from another tool. The location of the file is C:\ProgramData\GE Power Management\urpc\Offline, for example.
Page 644 The file is copied from the computer to the location specified. To save list of sites and devices with an Environment backup: In EnerVista, click File > Environment > Backup. A window opens. Name and save the .ENV file. 10-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 645: Restore Settings
These messages display because the roles of the protection engineer and network engineer can be separate. The former can require a URS file, while the latter can require stored Modbus settings and protection schemes. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-11...
Page 646 EnerVista UR Setup software. To restore the list of sites and devices from an Environment backup: In EnerVista, click File > Environment > Restore. A window opens. Select the .ENV file to restore. 10-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 647: Upgrade Software
Click the OK button to save the change. 10.9 Upgrade firmware If upgrading both EnerVista software and F60 firmware, upgrade the software first. The firmware of the F60 device can be upgraded, locally or remotely, using the EnerVista software. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-13...
Page 648 You access the Convert Device Settings option by right-clicking the file in the Offline Window area at the lower left. GE recommends converting settings in firmware steps, for example when converting from 6.0 to 7.4x, convert first to 7.0 then 7.4 in order to follow embedded conversion rules and keep settings. Note that the values of all settings that have been defaulted during conversion are not listed in the conversion report;...
Page 649: Replace Front Panel
For an enhanced front panel, loosen the thumb screw and open slightly the front panel. For a standard front panel, lift up the black plastic latch on the right side of the front panel and open slightly the front panel. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-15...
Page 650 With a Phillips screwdriver, unscrew and remove the mounting bracket on the right side of the unit. The bracket for the enhanced front panel looks similar to that for the graphical front panel, but they are not the same. 10-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 651 Figure 10-15: Remove standard front panel mounting bracket on right side Open the front panel. Unplug or unscrew the grey ground cable from the front panel. Unplug the RJ45 connector from the CPU module in the second slot on the left. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-17...
Page 652 Unscrew and remove the mounting bracket with the front panel from the left side. Figure 10-17: Unscrew enhanced front panel mounting bracket on left side Figure 10-18: Unscrew standard front panel mounting bracket on left side 10-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 653 Figure 10-19: Attach mounting bracket to relay on left side (no power supply module in first slot) Screw the right mounting bracket to the right side of the relay. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-19...
Page 654 Close the front panel without tightening the screw to the mounting bracket. Optionally remove the protective plastic film on the graphical front panel. It is normally peeled off, but also can be left The graphical front panel has been installed but not connected. 10-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 655 Ensure that the RS485 connector and the black cover plate are not on the back of the CPU module before sliding the module into the front of the relay. Figure 10-23: Rear of a CPU module before insertion without RS485 connector or cover plate F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-21...
Page 656 Insert the silver SFP connector(s) at the back of the CPU module, then connect any Ethernet connection(s). Power up the relay. If the graphical front panel does not power up immediately, disconnect power, open the front 10-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 657: Replace Module
Open the enhanced front panel to the left once the thumb screw has been removed. This allows for easy access of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and allows easy access to all modules in the F60. Figure 10-26: Modules inside relay with front cover open (enhanced front panel) F60 FEEDER PROTECTION SYSTEM –...
Page 658: Battery
When required, the battery can be replaced. The power supply module contains the battery. The battery type is 3 V cylindrical. 10.12.1 Replace battery for SH/SL power supply When required, the battery can be replaced. The power supply module contains the battery. 10-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 659 10. Reinstall the battery holder and the metal cover, and reinsert the power supply module into the unit. 11. Power on the unit. 12. Dispose of the old battery as outlined in the next section. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-25...
Page 660: Dispose Of Battery
(Cd), el plomo (Pb), o el mercurio (Hg ). Para el reciclaje apropiado, devuelva este producto a su distribuidor ó deshágase de él en los puntos de reciclaje designados. Para mas información : wwwrecyclethis.info. 10-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 661 (Cd), lood (Pb) of kwik (Hg). Voor correcte vorm van kringloop, geef je de producten terug aan jou locale leverancier of geef het af aan een gespecialiseerde verzamelpunt. Meer informatie vindt u op de volgende website: www.recyclethis.info. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-27...
Page 662 Bu sembolle işaretlenmiş piller Kadmiyum(Cd), Kurşun(Pb) ya da Civa(Hg) içerebilir. Doğru geri dönüşüm için ürünü yerel tedarikçinize geri veriniz ya da özel işaretlenmiş toplama noktlarına atınız. Daha fazla bilgi için: www.recyclethis.info. 10-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 663: Clear Files And Data After Uninstall
For issues not solved by troubleshooting, the process to return the device to the factory for repair is as follows: • Contact a GE Grid Solutions Technical Support Center. Contact information is found in the first chapter. • Obtain a Return Materials Authorization (RMA) number from the Technical Support Center.
Page 664: Storage
Customers are responsible for shipping costs to the factory, regardless of whether the unit is under warranty. • Fax a copy of the shipping information to the GE Grid Solutions service department in Canada at +1 905 927 5098. Use the detailed return procedure outlined at https://www.gegridsolutions.com/multilin/support/ret_proc.htm...
Page 665: Flexanalog Items
Field RTD 8 Value Field RTD 8 value 5832 Field TDR 1 Value Field TDR 1 value 5834 Field TDR 2 Value Field TDR 2 value 5836 Field TDR 3 Value Field TDR 3 value F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 666 6228 SRC 2 Ig RMS Amps Source 2 ground current RMS 6230 SRC 2 Ig Mag Amps Source 2 ground current magnitude 6232 SRC 2 Ig Angle Degrees Source 2 ground current angle F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 667 6358 SRC 4 Ig Mag Amps Source 4 ground current magnitude 6360 SRC 4 Ig Angle Degrees Source 4 ground current angle 6361 SRC 4 I_0 Mag Amps Source 4 zero-sequence current magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 668 SRC 2 Vbc RMS Volts Source 2 phase BC voltage RMS 6739 SRC 2 Vca RMS Volts Source 2 phase CA voltage RMS 6741 SRC 2 Vab Mag Volts Source 2 phase AB voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 669 SRC 4 Vag Mag Volts Source 4 phase AG voltage magnitude 6856 SRC 4 Vag Angle Degrees Source 4 phase AG voltage angle 6857 SRC 4 Vbg Mag Volts Source 4 phase BG voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 670 Source 2 phase B reactive power 7214 SRC 2 Qc Vars Source 2 phase C reactive power 7216 SRC 2 S Source 2 three-phase apparent power 7218 SRC 2 Sa Source 2 phase A apparent power F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 671 SRC 2 Demand Ib Amps Source 2 phase B current demand 7700 SRC 2 Demand Ic Amps Source 2 phase C current demand 7702 SRC 2 Demand Watt Watts Source 2 real power demand F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 672 SRC 1 Vb Harm[12] Source 1 phase B voltage twelfth harmonic 8101 SRC 1 Vb Harm[13] Source 1 phase B voltage thirteenth harmonic 8102 SRC 1 Vb Harm[14] Source 1 phase B voltage fourteenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 673 SRC 2 Va Harm[9] Source 2 phase A voltage ninth harmonic 8148 SRC 2 Va Harm[10] Source 2 phase A voltage tenth harmonic 8149 SRC 2 Va Harm[11] Source 2 phase A voltage eleventh harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 674 SRC 2 Vc Harm[6] Source 2 phase C voltage sixth harmonic 8195 SRC 2 Vc Harm[7] Source 2 phase C voltage seventh harmonic 8196 SRC 2 Vc Harm[8] Source 2 phase C voltage eighth harmonic A-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 675 Fault 1 pre-fault phase B voltage magnitude 9038 Prefault Vb Ang [1] Degrees Fault 1 pre-fault phase B voltage angle 9039 Prefault Vc Mag [1] Volts Fault 1 pre-fault phase C voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-11...
Page 676 Phasor measurement unit 1 phase B voltage angle 9587 PMU 1 Vc Mag Volts Phasor measurement unit 1 phase C voltage magnitude 9589 PMU 1 Vc Angle Degrees Phasor measurement unit 1 phase C voltage angle A-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 677 SRC 1 Ia Harm[20] Source 1 phase A current twentieth harmonic 10260 SRC 1 Ia Harm[21] Source 1 phase A current twenty-first harmonic 10261 SRC 1 Ia Harm[22] Source 1 phase A current twenty-second harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-13...
Page 678 SRC 1 Ic Harm[17] Source 1 phase C current seventeenth harmonic 10323 SRC 1 Ic Harm[18] Source 1 phase C current eighteenth harmonic 10324 SRC 1 Ic Harm[19] Source 1 phase C current nineteenth harmonic A-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 679 SRC 2 Ib Harm[14] Source 2 phase B current fourteenth harmonic 10386 SRC 2 Ib Harm[15] Source 2 phase B current fifteenth harmonic 10387 SRC 2 Ib Harm[16] Source 2 phase B current sixteenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-15...
Page 680 SRC 3 Ia Harm[11] Source 3 phase A current eleventh harmonic 10449 SRC 3 Ia Harm[12] Source 3 phase A current twelfth harmonic 10450 SRC 3 Ia Harm[13] Source 3 phase A current thirteenth harmonic A-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 681 SRC 3 Ic Harm[8] Source 3 phase C current eighth harmonic 10512 SRC 3 Ic Harm[9] Source 3 phase C current ninth harmonic 10513 SRC 3 Ic Harm[10] Source 3 phase C current tenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-17...
Page 682 SRC 4 Ib Harm[5] Source 4 phase B current fifth harmonic 10575 SRC 4 Ib Harm[6] Source 4 phase B current sixth harmonic 10576 SRC 4 Ib Harm[7] Source 4 phase B current seventh harmonic A-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 683 Synchrocheck 1 delta voltage 10850 Synchchk 1 Delta Phs Degrees Synchrocheck 1 delta phase 10851 Synchchk 1 SSCP DPh Degrees Synchrocheck 1 synchscope 10852 Synchchk 1 Delta F Synchrocheck 1 delta frequency F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-19...
Page 684 Breaker 1 Acc arcing amp phase A 12034 Brk 1 Acc Arc Amp B kA2-cyc Breaker 1 Acc arcing amp phase B 12036 Brk 1 Acc Arc Amp C kA2-cyc Breaker 1 Acc arcing amp phase C A-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 685 DCmA input 7 actual value 13518 DCmA Ip 8 DCmA input 8 actual value 13520 DCmA Ip 9 DCmA input 9 actual value 13522 DCmA Ip 10 DCmA input 10 actual value F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-21...
Page 686 RTD input 30 actual value 13582 RTD Ip 31 RTD input 31 actual value 13583 RTD Ip 32 RTD input 32 actual value 13584 RTD Ip 33 RTD input 33 actual value A-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 687 45606 RxGOOSE Analog 12 RxGOOSE analog input 12 45608 RxGOOSE Analog 13 RxGOOSE analog input 13 45610 RxGOOSE Analog 14 RxGOOSE analog input 14 45612 RxGOOSE Analog 15 RxGOOSE analog input 15 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-23...
Page 688 Volts HIZ Ig harmonics 10 63278 HZ Ig Harmonics[11] Volts HIZ Ig harmonics 11 63279 HZ Ig Harmonics[12] Volts HIZ Ig harmonics 12 63280 HZ Ig Harmonics[13] Volts HIZ Ig harmonics 13 A-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 689 Volts HIZ Ig harmonics 57 63325 HZ Ig Harmonics[58] Volts HIZ Ig harmonics 58 63326 HZ Ig Harmonics[59] Volts HIZ Ig harmonics 59 63327 HZ Ig Harmonics[60] Volts HIZ Ig harmonics 60 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-25...
Page 690 Volts HIZ Ig harmonics 61 63329 HZ Ig Harmonics[62] Volts HIZ Ig harmonics 62 63330 HZ Ig Harmonics[63] Volts HIZ Ig harmonics 63 63331 HZ Ig Harmonics[64] Volts HIZ Ig harmonics 64 A-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 691: B Radius Server
UR device for successful authentication, and the shortname is a short, optional alias that can be used in place of the IP address. client 10.0.0.2/24 { secret = testing123 shortname = private-network-1 In the <Path_to_Radius>\etc\raddb folder, create a file called dictionary.ge and add the following content. # ########################################################## GE VSAs ############################################################ VENDOR...
Page 692 Access Settings > Product Setup > Security. Configure the IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the clients.conf file. Restart the relay for the IP address and port changes to take effect.
Page 693: C Command Line
When the Supervisor account is enabled, the 'Lock Relay' setting must first be changed to No before the putsettings, inservice, or reboot command can be used. This setting cannot be changed using the command line interface. • Use quotes ("") to enclose any parameter containing a space F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 694 For non-CyberSentry devices — Set <authentication type> to "traditional". Note that <authentication type> defaults to "traditional" if not specified. Set <account> to "COMMANDS" or "SETTINGS". If not specified, the SETTINGS account is used. Example: SetupCLI URPC login -d "C30 Melbourne" -A traditional -a SETTINGS -w 1password1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 695 Read settings from device <device> and save them to the .urs file <File>. The <File> must not already exist. The default path to the output file is C:\Users\Public\Public Documents\GE Power Management\URPC\Data Example: SetupCLI URPC getsettings -d C30 -f "C30 Markham.urs"...
Page 696 SetupCLI URPC getsettings -d demoDevice -f devicefile.urs SetupCLI URPC compare -f existingfile.urs -r devicefile.urs -o output.txt The output is similar to the following: Comparing settings file aaa.urs : C:\Users\Public\Public Documents\GE Power Management\URPC\Data\ with bbb.urs : C:\Users\Public\Public Documents\GE Power Management\URPC\Data\ Setting Name...
Page 697 SetupCLI URPC getsettings -d DEV@SETUP_CLI -f "example file.urs" SetupCLI URPC logout -d DEV@SETUP_CLI SetupCLI URPC exit DEV@SETUP_CLI has to be used as the device name in the commands followed by the 'adddevice' command. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 698 COMMAND LINE INTERFACE APPENDIX C: COMMAND LINE INTERFACE F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 699: Warranty
This chapter provides the warranty and revision history. D.1 Warranty For products shipped as of 1 October 2013, GE Grid Solutions warrants most of its GE manufactured products for 10 years. For warranty details including any limitations and disclaimers, see the Terms and Conditions at http://www.gegridsolutions.com/multilin/warranty.htm...
Page 700 1 August 2013 13-0401 1601-0093-AB1 7.3x 7 November 2014 14-1408 1601-0093-AB2 7.3x 1 September 2015 15-2215 1601-0093-AC1 7.40x 8 December 2016 16-3319 1601-0093-AE1 7.41x 31 January 2017 17-3427 1601-0093-AE3 7.4x 28 April 2017 17-3561 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 701 Release date 1601-0093-AF1 7.6x 30 June 2017 17-3779 Table D-2: Major changes for F60 manual version AF1 (English) Page Description General revision Updated "faceplate" to "front panel" for consistency and to reflect web site Added graphical front panel option to order codes and specifications in chapter 2, Interfaces chapter 4, Settings chapter 5, Actual Values chapter 6 Added PEAP-GTC and PAP protocols for authenticating user logins when using a RADIUS server.
Page 702 Modbus memory map, IMD tables. Did not add Single-Pole Tripping section to Theory of Operation chapter because single-pole tripping does not apply to F60. Did not add new Application of Settings chapter to add Protection Signaling Schemes section because section is POTT and not Pilot POTT.
Page 703 APPENDIX D: MISCELLANEOUS REVISION HISTORY F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 704 REVISION HISTORY APPENDIX D: MISCELLANEOUS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 705 Full Load Current Contact Output Fiber Optic Communication FPGA Field-programmable Gate Array COMM Communications FREQ Frequency COMP Compensated, Comparison Frequency-Shift Keying CONN Connection File Transfer Protocol CONT Continuous, Contact FlexElement™ CO-ORD Coordination Forward F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 706 Protection Low Voltage Parallel Redundancy Protocol PSEL Presentation Selector Machine Precision Time Protocol Machine to Machine Per Unit MilliAmpere PUIB Pickup Current Block Magnitude PUIT Pickup Current Trip Manual / Manually PUSHBTN Pushbutton F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 707 Time Dial Multiplier TEMP Temperature TFTP Trivial File Transfer Protocol Total Harmonic Distortion Timer Time Overcurrent Time Overvoltage TRANS Transient TRANSF Transfer TSEL Transport Selector Time Undercurrent Time Undervoltage TX (Tx) Transmit, Transmitter F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 708 ABBREVIATIONS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 710 FlexLogic operands ...............5-191 menu ......................7-1 logic diagram ...................5-320 with IEC 61850 ................... 5-94 settings ....................5-318 Commissioning ..................8-1 specifications ..................2-24 Breaker-and-a-half scheme ............5-6 Brightness ....................5-26 Broken conductor FlexLogic operands ...............5-192 settings ....................5-329 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 711 DCmA outputs settings ....................5-301 description ................... 3-30 CPU module diagram ................3-11 settings ....................5-353 CPU, new types T, U, V ..............10-15 specifications ..................2-33 CRC alarm .....................5-141 Decommission ..................10-29 Critical failure relay specifications ..........2-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 714 Frequency rate of change settings ....................5-65 actual values ..................6-24 FlexAnalogs ...................A-2 FlexLogic operands ...............5-193 logic diagram ...................5-286 settings ....................5-285 specifications ..................2-24 Frequency testing .................. 8-1 Frequency tracking ................6-24 Frequency, nominal .................5-146 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 718 Overfrequency FlexLogic operands ..............5-195 FlexLogic operands ...............5-194 logic diagram .................. 5-266 logic diagram ...................5-285 settings ....................5-265 settings ....................5-284 specifications ..................2-23 specifications ..................2-23 Phase rotation ..................5-146 testing ...................... 8-1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 720 EnerVista ..................5-1 using relay ....................7-3 Restore settings ................... 10-8 Restricted ground fault actual values ..................6-26 FlexAnalogs ...................A-1 FlexLogic operands ...............5-196 logic diagram ...................5-246 settings ....................5-243 specifications ..................2-20 Revision history ..................D-1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 723 User-programmable LEDs custom labels ..................4-44 defaults ....................4-42 settings ....................5-123 UDP for TFTP ..................5-100 specifications ..................2-26 UL certification ..................2-39 Unable to access device ..............3-66 Unable to put relay in flash mode ...........10-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 724 Warning, firmware upload not supported ......10-14 Warranty .....................D-1 Watt-hour specifications ..............2-29 Watt-hours ..................... 6-20 Wattmetric zero-sequence directional actual values ..................6-25 FlexLogic operands ...............5-198 logic diagram ...................5-240 settings ....................5-236 specifications ..................2-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...

GE F60 Instruction Manual

1 Introduction

Safety Symbols and Definitions

2 Product Description

Description

3 Installation

Unpack and Inspect

4 Interfaces

Enervista Software Interface

5 Settings

Settings Menu

6 Actual Values

Actual Values Menu

7 Commands and Targets

8 Commissioning

Testing

9 Theory of Operation

10 Maintenance

Convert Device Settings

Back up and Restore Settings

Upgrade Software

Quick Links

Related Manuals for GE F60

Summary of Contents for GE F60