Noise Information; Delivery Scope - Bosch 3 601 M23 630 Original Instructions Manual

71 Set screw for 45° basic setting (leftward bevel angle)
72 Set screw for 45° basic setting (rightward bevel angle)
73 Set screws of scale 37 for mitre angles
74 Screw for mitre angle indicator
Technical Data
Sliding Mitre Saw
Article number
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Weight according to EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 39.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter

Noise Information

Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.

Delivery Scope

Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Locking knob 15
– Dust bag 1
– Hex key 20
– Hex key 21 (below laser protection cap 27)
– Material clamp 22
Bosch Power Tools
75 Set screw for clamping force of lock lever 17
76 Velcro strap
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
3 601 M23 600
3 601 M23 630
3 601 M23 670
W
-1
min
nm
mW
kg
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
mm 305
devices are fully functional. Any lightly damaged parts must
mm 1.7–2.6
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
mm 30
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Open-end spanner (size: 8 mm)
– Ring, open-end or socket spanner (size: 10 mm and
17 mm)
Mounting the Locking Knob (see figure a)
– Screw the locking knob 15 into the corresponding drill
hole above the lever 16.
 Always tighten the locking knob 15 firmly before saw-
ing. Otherwise the saw blade can become wedged in the
workpiece.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figure b1)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 12 serve for this pur-
pose.
3 601 M23 660
2000 1500
3800 3800

635 635
< 1 < 1
2
32.1 32.1
/II /II
English | 35
GCM 12 GDL
3 601 M23 690
3 601 M23 6P0
1800
3800

–
635
< 1
2 2
32.1
/II
1 609 92A 285 | (11.11.15)