Samsung Galaxy Note 5 Repair Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Cell Phone
  5. galaxy note 5
  6. Repair manual

Samsung Galaxy Note 5 Repair Manual

Cellairis glass/lcd repair guide
Hide thumbs Also See for Galaxy Note 5:

Advertisement

Table of Contents

See also: Getting to Know , User Manual
Galaxy Note 5
Glass/Lcd
Version 1
2016 Edition

Advertisement

Table of Contents
loading

Related Manuals for Samsung Galaxy Note 5

Summary of Contents for Samsung Galaxy Note 5

  • Page 1 Galaxy Note 5 Glass/Lcd REPAIR GUIDE Version 1 2016 Edition...
  • Page 2 Samsung Galaxy Note 5 Glass/LCd REPAIR GUIDE RiAna Soto Repair Training Specialist rsoto@cellairis.com...
  • Page 3 FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND HAVE CUSTOMER SIGN THE CELLAIRIS REPAIR LIABILITY WAIVER FORM...
  • Page 4 PRE-REPAIR DEVICE CHECK-IN...
  • Page 5 TOOLS NEEDED • Philips screwdriver • Spudger • Tweezers • Isesamo • Pentalobe screwdriver • Magnetic Mat • Note 5 Digitizer/LCD...
  • Page 6 HEAT-GUN PRECAUTIONS Always operate the heat gun on the lowest setting. • Keep face, hands, hair, and clothing away from the air stream. • The air nozzle also becomes extremely hot. Never grab the heat gun by the nozzle. • Never operate the heat gun by laying it on its side on a table.
  • Page 7 ADDITIONAL PRECAUTIONS Magnetic Pad: During the repair, you will be utilizing a magnetic pad to organize the plethora of • differing screws that you will be pulling out of the iPhone 6S. Below is a list of several internal components of the iPhone 6S that should never be placed on the pad, or you risk damaging the hardware or erasing client data: LCD/Digitizer Assembly •...
  • Page 8 ADDITIONAL PRECAUTIONS Power on/off: To avoid any damage to the hardware during the repair, it is best to have the device • powered off until you can get to and disconnect the battery. Battery: Never unplug any flex cables unless the battery has been completely disconnected to avoid •...
  • Page 9 Tools: sim card ejector STEP 1 Disassemble the device • Power off device. • Remove sim card.
  • Page 10 Tools: plastic cards, heat gun, Tips: If the back glass is already broken most likely it will break isesamo or painters knife more as you heat it up and pry it off. Make sure to mention this to STEP 2 the customer so they are aware.
  • Page 11 Tools: Philips screwdriver, tweezers STEP 3 Disassemble the device • Now that the back glass is removed. • Unscrew the twenty (20) Philips screws with the Philips screwdriver. • Peel back black tape to expose the battery ( area pointed out with arrows).
  • Page 12 Tools: Hands, spudger STEP 4 Disassemble the device • Once the black tape is pulled back use your thumb to help push the frame from the display. • The black tape covers the battery so now that the battery is exposed it allows room to separate the frame from glass display.
  • Page 13 Tools: spudger, tweezers STEP 5 • Disconnect the Lcd flex cable. Disassemble the device • Then the ear speaker cable above the camera. • Next, disconnect the Digitizer cable. • Moving down the board disconnect the two antennas one is white and the other blue. •...
  • Page 14 Tools: Heat gun, painters knife or isesamo STEP 6 Disassemble the device • Once the motherboard is all disconnected and removed it is time to separate the old assembly from the frame of the device. Turn device over to the front of the glass and heat. It does not matter if you heat to long on that side because most likely the lcd is already damaged.
  • Page 15 Tools: Painters knife or isesamo, spudger STEP 7 Disassemble the device The closer you get to the bottom of the glass be • aware there are two flex cables attached by adhesive. Heating the front of the glass in that area will help loosen the adhesive.
  • Page 16 Tools: Philips screwdriver, spudger, Fingers, STEP 1 PDI pads. Reassemble of Device • Use a scraping tool to clean the frame of old adhesive and remaining glass shards. (PDI pads are good for removing adhesive) (area shown by red arrows). •...
  • Page 17 Tools: Philips screwdriver, spudger, Fingers STEP 2 • After the motherboard is positioned properly reconnect all components and cables but, make sure the battery is reconnected last. • Place back housing over the device by starting at the bottom, lining the chargeport into the socket designated for it. Push down on the top of the glass display because the top has hinges that need to be cleared before frame fits all the way into the frame.
  • Page 18 Tools: Philips screwdriver, spudger, Fingers STEP 3 Reassemble of Device • We can now screw in all the twenty (20) Philips screws with a Philips screw driver.
  • Page 19 Tools: Philips screwdriver, adhesive, scissors, Fingers STEP 4 • Next, put the back glass back on now if it’s the original glass you might need to add a thin layer of adhesive around the frame of the back glass. Outlined with the white shade of tape around the frame. If it’s a replacement back glass and doesn’t come with adhesive on it definitely add some around the frame.
  • Page 20 STEP 6 • Run through each of these test for the post test.

  • Page 21: Troubleshooting

    STEP 7 Troubleshooting • After the repair is done make sure the touch is responsive. If you notice that the touch is delayed could mean the part is defective. Try a new one.
  • Page 22 C O N T A C T Riana Soto REPAIR 678.513.4020 x400 TRAINING rsoto@cellairis.com...

Table of Contents