Asus ROG RAMPAGE VI EXTREME Manual
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Motherboard
  5. ROG RAMPAGE VI EXTREME
  6. Manual

Asus ROG RAMPAGE VI EXTREME Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ROG
RAMPAGE VI
EXTREME

Advertisement

Table of Contents
loading

Related Manuals for Asus ROG RAMPAGE VI EXTREME

Summary of Contents for Asus ROG RAMPAGE VI EXTREME

  • Page 1 RAMPAGE VI EXTREME...
  • Page 2 Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

  • Page 3: Table Of Contents

    Contents Safety information ...................... vi About this guide ......................vii ROG RAMPAGE VI EXTREME specifications summary ......... ix Package contents ...................... xv Installation tools and components ................. xvi Chapter 1: Product Introduction Motherboard overview ................1-1 1.1.1 Before you proceed ..............1-1 1.1.2...
  • Page 4 3.6.14 PCH-FW Configuration ............. 3-20 Monitor menu ................... 3-20 Boot menu ....................3-21 Tool menu ....................3-22 3.9.1 ASUS EZ Flash 3 Utility ............3-22 3.9.2 Secure Erase ................3-23 3.9.3 ASUS Overclocking Profile ............3-24 3.9.4 BIOS FlashBack ................ 3-24 3.9.5...
  • Page 5 Virtual Raid on CPU in UEFI BIOS ........4-6 ® 4.1.5 Intel Rapid Storage Technology Option ROM utility ....4-12 ® Creating a RAID driver disk ..............4-16 4.2.1 Creating a RAID driver disk in Windows ......... 4-16 ® Appendix Notices ........................A-1 ASUS contact information ..................A-8...

  • Page 6: Safety Information

    Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

  • Page 7: About This Guide

    Refer to the following sources for additional information and for product and software updates. ASUS website The ASUS website (www.asus.com) provides updated information on ASUS hardware and software products. Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer.

  • Page 8: Conventions Used In This Guide

    Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task.

  • Page 9: Rog Rampage Vi Extreme Specifications Summary

    ROG RAMPAGE VI EXTREME specifications summary Intel Socket 2066 for Intel Core™ X-Series Processor 79xx, 78xx Series ® ® Supports 14nm CPU Supports Intel Virtual RAID on CPU (VROC)* ® Supports Intel Turbo Boost Max Technology 3.0* ® * Support of these features depends on the CPU types.
  • Page 10 ROG RAMPAGE VI EXTREME specifications summary Aquantia AQC-107 10G LAN Intel I219-V Gigabit LAN- Dual interconnect between the integrated ® Media Access Controller (MAC) and physical layer (PHY) Anti-surge LANGuard ROG GameFirst Technology Wi-Fi 802.11ad(WiGig) supports frequency band 60GHz* Up to 4.6Gbps Wireless Data 2x2 MU-MIMO 802.11 a/b/g/n/ac supports dual frequency band 2.4/5 GHz...
  • Page 11 ROG RAMPAGE VI EXTREME specifications summary 1 x 4-pin VROC key 1 x USB 3.1 Gen 2 front panel connector 2 x USB 3.1 Gen 1 connectors support additional 4 USB 3.1 Gen 1 ports 1 x USB connector supports 2 USB 2.0 ports...
  • Page 12 ROG RAMPAGE VI EXTREME specifications summary 1 x Clear CMOS button 1 x BIOS Flashback button 1 x ASUS Wi-Fi GO! module (1x1 802.11 ad Wi-Fi + 2x2 MU-MIMO 802.11 a/b/g/n/ac and Bluetooth v4.1) 1 x Aquantia AQC-107 10G LAN...
  • Page 13 ROG RAMPAGE VI EXTREME specifications summary ROG DIMM.2 module Extreme Engine Digi+ - MicroFine Alloy Choke - NexFET MOSFET - 10K Black Metallic Capacitors OC Zone - ReTry button - Safe Boot button - LN2 Mode header - Slow Mode switch...
  • Page 14 ROG RAMPAGE VI EXTREME specifications summary 128 Mb Flash ROM, UEFI AMI BIOS, PnP, WfM2.0, SM BIOS 3.0, ACPI 6.0, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, F11 EZ Tuning Wizard, F6 Qfan Control, F3 My Favorites, Last Modified log, F12...

  • Page 15: Package Contents

    1 x Cable for Fan Extension card 1 x Extension cable for addressable RGB strip 1 x Extension cable for RGB strip (80cm) 1 x ASUS 2x2 dual band Wi-Fi antenna (Wi-Fi 802.11a/b/g/n/ ac compliant) 1 x ASUS Wi-Fi 802.11ad(WiGig) moving antenna (available...

  • Page 16: Installation Tools And Components

    Installation tools and components Intel ® LGA 2066 CPU Intel LGA 2066 compatible CPU Fan ® Phillips (cross) screwdriver SATA hard disk drive PC chassis DIMM 1 bag of screws Power supply unit SATA optical disc drive (optional) Graphics card M.2 SSD module (optional) The tools and components in the table above are not included in the motherboard package.

  • Page 17: Chapter 1: Product Introduction

    Chapter 1: Product Introduction Product Introduction Motherboard overview 1.1.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them. • Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. • Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. ROG RAMPAGE VI EXTREME...

  • Page 18: Motherboard Layout

    1.1.2 Motherboard layout Refer to 1.1.9 Internal connectors and 2.3.1 Rear I/O connection for more information about rear panel connectors and internal connectors. Chapter 1: Product Introduction...

  • Page 19: Layout Contents

    25. Thunderbolt header (5-pin TB_HEADER) 1-25 26. Addressable RGB header (4-1 pin ADD_HEADER) 1-27 27. MemOK! button 1-10 28. M.2 sockets (M.2_1(Socket 3)) 1-28 29. USB 2.0 connector (10-1 pin USB1314) 1-21 30. ROG Extension connector (18-1 pin ROG_EXT) 1-31 31. LN2 Mode jumper (3-pin LN2_MODE) 1-15 32. TPM connector (14-1 pin TPM) 1-31 33. Front panel audio connector (10-1 pin AAFP) 1-19 34. LED connector (13-pin LED_CON2) 1-25 35. OLED connector (9-pin OLED_HEADER) 1-32 36. Water Block connector (9 pin WB_SENSOR) 1-30 ROG RAMPAGE VI EXTREME...

  • Page 20: Central Processing Unit (Cpu)

    1.1.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA2066 socket designed for the Intel ® Core™ X-series Processor 79xx, 78xx Series. • Ensure that all power cables are unplugged before installing the CPU. • Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related. • Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA2066 socket. • The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap. Chapter 1: Product Introduction...

  • Page 21: System Memory

    1.1.4 System memory The motherboard comes with eight DDR4 (Double Data Rate 4) Dual Inline Memory Modules (DIMM) slots. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot. Recommended memory configurations ROG RAMPAGE VI EXTREME...

  • Page 22: Memory Configurations

    Memory configurations You may install 2 GB, 4 GB, 8 GB and 16 GB unbuffered and non-ECC DDR4 DIMMs into the DIMM sockets. For Intel Core™ X-Series Processor 78xx, 79xx Series, you may install varying memory ® sizes in Channel A, Channel B, Channel C, and Channel D. The system maps the total size of the lower-sized channel for the quad-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value. • For system stability, use a more efficient memory cooling system to support a full memory load (8 DIMMs) or overclocking condition. • Always install the DIMMS with the same CAS Latency. For an optimum compatibility, we recommend that you install memory modules of the same version or data code (D/C) from the same vendor. Check with the vendor to get the correct memory modules. • Visit the ASUS website for the latest QVL. Chapter 1: Product Introduction...

  • Page 23: Expansion Slots

    1.1.5 Expansion slots Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Slot No. Slot Description PCIE x16/x8_1 slot PCIE x8_2 slot PCIE x4_1 slot PCIE x16/x8_3 slot PCIE x8_4 slot ROG RAMPAGE VI EXTREME...
  • Page 24 44-Lane CPUs PCI Express 3.0 operating mode VGA / PCIe Single VGA / Dual VGA / Triple VGA / Triple VGA / Quad VGA / configuration PCIe card PCIe cards PCIe cards* PCIe cards PCIe cards PCIex16/x8_1 PCIex8_2 PCIex16/x8_3 PCIex8_4 * Please use the bundled 4-way SLI ®...

  • Page 25: Onboard Buttons And Switches

    1.1.6 Onboard buttons and switches Onboard buttons and switches allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. Power-on button The motherboard comes with a power-on button that allows you to power up or wake up the system. The button also lights up when the system is plugged to a power source indicating that you should shut down the system and unplug the power cable before removing or installing any motherboard component. Reset button Press the reset button to reboot the system. ROG RAMPAGE VI EXTREME...
  • Page 26 • Refer to section 1.1.8 Onboard LEDs for the exact location of the DRAM_LED. • The DRAM_LED also lights up when the DIMM is not properly installed. Turn off the system and reinstall the DIMM before using the MemOK! function. • The MemOK! button does not function under Windows OS environment. ® • During the tuning process, the system loads and tests failsafe memory settings. It takes about 30 seconds for the system to test one set of failsafe settings. If the test fails, the system reboots and tests the next set of failsafe settings. The blinking speed of the DRAM_LED increases, indicating different test processes. • Due to memory tuning requirement, the system automatically reboots when each timing set is tested. If the installed DIMMs still fail to boot after the whole tuning process, the DRAM_LED lights continuously. Replace the DIMMs with ones recommended in the Memory QVL (Qualified Vendors Lists) at www.asus.com. • If you turn off the computer and replace DIMMs during the tuning process, the system continues memory tuning after turning on the computer. To stop memory tuning, turn off the computer and unplug the power cord for about 5–10 seconds. • If your system fails to boot up due to BIOS overclocking, press the MemOK! button to boot and load the BIOS default settings. A message will appear during POST reminding you that the BIOS has been restored to its default settings. • We recommend that you download and update to the latest BIOS version from www.asus.com after using the MemOK! function. Chapter 1: Product Introduction 1-10...
  • Page 27 Safe Boot button (SAFE_BOOT) The Safe Boot button can be pressed anytime to force the system to reboot into the BIOS safe mode. This button temporarily applies safe settings to the BIOS while retaining any overclocked settings allowing you to modify the settings causing boot failure. Use this button when overclocking or tweaking the settings of your system. ReTry button (RETRY_BUTTON) The ReTry button is specially designed for overclockers and is most useful during the booting process where the Reset button is rendered useless. When pressed, it forces the system to reboot while retaining the same settings to be retried in quick succession to achieve a successful POST. ROG RAMPAGE VI EXTREME 1-11...
  • Page 28 BIOS Switch button (BIOS_SWITCH) The motherboard comes with two BIOS chips. Press the BIOS button to switch BIOS and load different BIOS settings. The nearby BIOS_LEDs indicate the currently selected BIOS. Pause switch (PAUSE) The pause switch allows you to freeze the cooling system at a hardware level, thus allowing you to adjust your system settings under heavy overclocking. Chapter 1: Product Introduction 1-12...
  • Page 29 Slow Mode switch (SLOW_MODE) Slow Mode Switch is employed during LN2 benching. The system may crash due to the CPU being unstable when using extreme overclocking, enabling slow mode will decrease the processor frequency and stabilize the system, allowing overclockers to keep track of their overclocking data. RSVD switch (RSVD_1-2) This switch is reserved for ASUS-authorized technicians only. Ensure to set this switch to disabled, enabling this switch may cause system failure. ROG RAMPAGE VI EXTREME 1-13...
  • Page 30 PCIe x16 Lane switch (PCIEX16_SW) These slide switches allows you to enable and disable the corresponding PCIe x16 slots. When one of the installed PCIe x16 cards is out of order, you can use the slide switch to find the faulty one without removing the cards. Chapter 1: Product Introduction 1-14...

  • Page 31: Jumpers

    1.1.7 Jumpers LN2 Mode jumper (3-pin LN2_MODE) With LN2 mode activated, the ROG motherboard is optimized to remedy the cold-boot bug during POST and help the system boot successfully. ROG RAMPAGE VI EXTREME 1-15...

  • Page 32: Onboard Leds

    1.1.8 Onboard LEDs Q LEDs (CPU, DRAM, VGA, BOOT) Q LEDs check key components (CPU, DRAM, VGA card, and booting devices) in sequence during motherboard booting process. If an error is found, the corresponding LED remains lit until the problem is solved. This user-friendly design provides an intuitive way to locate the root problem within seconds. The Q LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case. BIOS LEDs (BIOS_LED1-2) The BIOS LEDs help indicate the BIOS activity. Press the BIOS button to switch between BIOS1 and BIOS2 and the LED lights up when the corresponding BIOS is in use. Chapter 1: Product Introduction 1-16...
  • Page 33 DIMM LED (DIMM_A_LED; DIMM_B_LED; DIMM_C_LED; DIMM_D_LED) The DIMM LED indicates when the corresponding memory channel is enabled. Hard Disk LED (HD_LED) The Hard Disk LED is designed to indicate the hard disk activity. It blinks when data is being written into or read from the hard disk drive. The LED does not light up when there is no hard disk drive connected to the motherboard or when the hard disk drive does not function. ROG RAMPAGE VI EXTREME 1-17...

  • Page 34: Internal Connectors

    1.1.9 Internal connectors Intel Serial ATA 6 Gb/s connectors (7-pin SATA6G_12; SATA 6G_34; ® SATA 6G_56) These connectors connect to Serial ATA 6 Gb/s hard disk drives via Serial ATA 6 Gb/s signal cables. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel Rapid Storage Technology through the onboard Intel ® ® X299 chipset. • These connectors are set to [AHCI Mode] by default. If you intend to create a Serial ATA RAID set using these connectors, set the SATA Mode item in the BIOS to [Intel RST Premium With Intel Optane System Acceleration (RAID)]. • Due to the way Intel reads drive numbers based on the PCH pinout, the SATA drive naming on the IRST driver will be shifted by 2 (i.e. SATA_1 will be reported as internal empty port 3. Chapter 1: Product Introduction 1-18...
  • Page 35 Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this connector. We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability. USB 3.1 Gen 2 front panel connector (U31G2_E2) This connector allows you to connect a USB 3.1 Gen 2 module for additional USB 3.1 Gen 2 ports. The latest USB 3.1 Gen 2 connectivity provides data transfer speeds of up to 10 Gbps. ROG RAMPAGE VI EXTREME 1-19...
  • Page 36 USB 3.1 Gen 1 connector (20-1 pin U31G1_E12; 20-1 pin U31G1_E34) These connectors allow you to connect a USB 3.1 Gen 1 module for additional USB 3.1 Gen 1 front or rear panel ports. With an installed USB 3.1 Gen 1 module, you can enjoy all the benefits of USB 3.1 Gen 1 including faster data transfer speeds of up to 5 Gb/s, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. The USB 3.1 Gen 1 module is purchased separately. The plugged USB 3.1 Gen 1 device may run on xHCI or EHCI mode depending on the operating system’s setting. Chapter 1: Product Introduction 1-20...
  • Page 37 USB 2.0 connector (10-1 pin USB1314) This connector is for USB 2.0 ports. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. This USB connector complies with USB 2.0 specification that supports up to 480 Mb/s connection speed. Thermal sensor connectors (2-pin T_SENSOR1-2) These connectors are for the thermistor cables that monitor the temperature of the devices and the critical components inside the motherboard. Connect the thermistor cable and place the sensor on the device or the motherboard’s component to detect its temperature. ROG RAMPAGE VI EXTREME 1-21...
  • Page 38 CPU, CPU optional, high amp, water pump+, extension, and chassis fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin H_AMP_FAN; 4-pin W_ PUMP+1; 4-pin W_PUMP+2; 5-pin EXT_FAN; 4-pin CHA_FAN1-3) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. • DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! • Ensure that the CPU fan cable is securely installed to the CPU fan connector. • The CPU_FAN connector supports the CPU fan of maximum 1A (12 W) fan power. • The EXT_FAN connector supports 2 of 5 thermal sensor sources. • W_PUMP+ function support depends on water cooling device.
  • Page 39 ATX power connectors (24-pin EATXPWR; 8-pin EATX12V1; 4-pin EATX12V2; 4-pin EZ_PLUG) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power plugs. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12V Specification 2.0 (or later version) and provides a minimum power of 350 W. • We recommend that you use a PSU with a higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. • If you want to use two or more high-end PCI Express x16 cards, use a PSU with 1000W power or above to ensure the system stability. ROG RAMPAGE VI EXTREME 1-23...

  • Page 40: System Panel Connector (10-1 Pin Panel)

    System panel connectors (10-1 pin F_PANEL; 4-pin SPEAKER) This connector supports several chassis-mounted functions. • System power LED (2-pin PLED) The 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. • Hard disk drive activity LED (2-pin HDLED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The HDD LED lights up or flashes when data is read from or written to the HDD. • System warning speaker (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. • ATX power button/soft-off button (2-pin PWRSW) This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the operating system settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF. • Reset button (2-pin RESET) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. Chapter 1: Product Introduction 1-24...
  • Page 41 Thunderbolt header (5-pin TB_HEADER) This connector is for the add-on Thunderbolt I/O card that supports Intel’s Thunderbolt Technology, allowing you to connect up to six Thunderbolt-enabled devices and a DisplayPort-enabled display in a daisy-chain configuration. The add-on Thunderbolt I/O card and Thunderbolt cables are purchased separately. LED connector (13-pin LED_CON2) This connector is for connecting LED strips on your cover. ROG RAMPAGE VI EXTREME 1-25...
  • Page 42 AURA RGB headers (4-pin RGB_HEADER1-2) These connectors are for RGB LED strips. The RGB header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum power rating of 2A (12V), and no longer than 2 m. Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. • Actual lighting and color will vary with LED strip. • If your LED strip does not light up, check if the RGB LED extension cable and the RGB LED strip is connected in the correct orientation, and the 12V connector is aligned with the 12V header on the motherboard. • The LED strip will only light up under the operating system. • The LED strip is purchased separately. Chapter 1: Product Introduction 1-26...
  • Page 43 Addressable RGB header (4-1 pin ADD_HEADER) This connector is for individually addressable RGB WS2812B LED strips or WS2812B based LED strips. The addressable RGB header supports WS2812B addressable RGB LED strips (5V/Data/ Ground), with a maximum power rating of 3A (5V) and a maximum of 60 LEDs. Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. • Actual lighting and color will vary with LED strip. • If your LED strip does not light up, check if the addressable RGB LED strip is connected in the correct orientation, and the 5V connector is aligned with the 5V header on the motherboard. • The addressable RGB LED strip will only light up under the operating system. • The addressable RGB LED strip is purchased separately. ROG RAMPAGE VI EXTREME 1-27...
  • Page 44 U.2 connector (U.2) This motherboard comes with a U.2 connector which supports PCIe 3.0 x4 NVM Express storage. The U.2 connector shares bandwidth with the M.2_1 socket . Adjust the BIOS settings to use U.2 devices. M.2 sockets (M.2_1(Socket 3)) This socket allows you to install an M.2 SSD module. • M.2_1 socket supports PCIe 3.0 x4 and SATA mode M Key design and type 2242 / 2260 / 2280 / 22110 PCIe and SATA storage devices. • These sockets support IRST (Intel Rapid Storage Technology). ® • The M.2_1 socket shares bandwidth with the U.2 connector. Adjust the BIOS settings to use U.2 devices. The M.2 SSD module is purchased separately. Chapter 1: Product Introduction 1-28...
  • Page 45 DIMM.2 slot (DIMM.2_SLOT) This socket allows you to install the bundled DIMM.2 card to connect M.2 SSD modules. • Before you install or remove the DIMM.2 card, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard or DIMM.2 card. • The DIMM.2 card is notched to fit in only one orientation. Ensure that the notch on your card is aligned correctly with the DIMM.2 slot before inserting the card. • M.2_1 socket supports PCIe 3.0 x4 M Key design and type 2230 / 2242 / 2260 / 2280 / 22110 PCIe storage devices. • M.2_2 socket supports PCIe 3.0 x4 and SATA mode M Key design and type 2230 / 2242 / 2260 / 2280 / 22110 storage devices. • These sockets support IRST (Intel Rapid Storage Technology). ® • Intel Optane Technology is only supported by M.2_1 and M.2_1(DIMM.2) when ® sourced from the PCH. Before using Intel Optane memory modules, ensure that you ® have updated your motherboard drivers and BIOS to the latest version from ASUS support website. The M.2 SSD module is purchased separately. ROG RAMPAGE VI EXTREME 1-29...
  • Page 46 Water in, water out, and water flow connectors (2-pin W_IN; 2-pin W_OUT; 3-pin W_FLOW) These connectors allow you to connect sensors to monitor the temperature and flow rate of your liquid cooling system. You can manually adjust the fans and water pump to optimize the thermal efficiency of your liquid cooling system. Water Block connector (9-pin WB_SENSOR) This connector allows you to connect a water block connector to monitor the temperature, flow rate, and water leak signals of your third party monoblocks. You can manually adjust the fans and water pump to optimize the thermal efficiency of your third party monoblocks. Chapter 1: Product Introduction 1-30...
  • Page 47 ROG extension connector (18-1 pin ROG_EXT) This connector is for the OC Panel I/II. • The OC Panel I/II is purchased separately. • Support for OC Panel I/II varies over different platforms. • Visit www.asus.com for more information about the devices and the latest compatibility list. TPM connector (14-1 pin TPM) This connector supports a Trusted Platform Module (TPM) system, which securely stores keys, digital certificates, passwords and data. A TPM system also helps enhance network security, protect digital identities, and ensures platform integrity. ROG RAMPAGE VI EXTREME 1-31...
  • Page 48 VROC_HW_KEY connector (4-pin VROC_HW_KEY) This connector allows you to connect a KEY module to enable CPU RAID functions with Intel CPU RSTe. ® • The KEY module is purchased separately. • Due to CPU behavior, CPU RAID functions with Intel CPU RSTe only supports Intel ® ® Core™ X-series Processor 79xx, 78xx Series, and Intel SSD modules. ® OLED connector (9-pin OLED_HEADER) This connector is used to connect your LiveDash OLED panel. The OLED panel provides you a quick overview of the system temperature, power status, and fan speeds when your system boots up. You can also upload a .gif file for a customized look. • Use the ROG LiveDash Utility to configure and customize the OLED panel. • The LiveDash OLED provides the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case. Chapter 1: Product Introduction 1-32...

  • Page 49: Probeit

    1.1.10 ProbeIt The ROG ProbeIt allows you to detect your system’s current voltage and OC settings. Use a multimeter to measure the ProbeIt points even during overclocking. See the illustration below to locate the respective ProbeIt points. Using ProbeIt You can connect the multimeter to the motherboard as shown on the following figure. The illustration above is for reference only, the actual motherboard layout and measure points may differ by model. ROG RAMPAGE VI EXTREME 1-33...
  • Page 50 Chapter 1: Product Introduction 1-34...

  • Page 51: Chapter 2: Basic Installation

    Please note the order in opening/ closing the double latch. Follow the instructions printed on the metal sealing hatch or the illustrations shown below in this manual. The plastic cap will pop up automatically once the CPU is in place and the hatch properly sealed down. ROG RAMPAGE VI EXTREME...
  • Page 52 Triangle mark Triangle mark Chapter 2: Basic Installation...

  • Page 53: Cpu Heatsink And Fan Assembly Installation

    2.1.2 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan, if necessary. To install the CPU heatsink and fan assembly: ROG RAMPAGE VI EXTREME...

  • Page 54: Motherboard Installation

    2.1.3 Motherboard installation Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel. Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. DO NOT overtighten the screws! Doing so can damage the motherboard.

  • Page 55: Dimm Installation

    2.1.4 DIMM installation To remove a DIMM ROG RAMPAGE VI EXTREME...

  • Page 56: Atx Power Connection

    2.1.5 ATX power connection • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power plugs. Chapter 2: Basic Installation...

  • Page 57: Sata Device Connection

    2.1.6 SATA device connection ROG RAMPAGE VI EXTREME...

  • Page 58: Front I/O Connector

    2.1.7 Front I/O connector To install ASUS Q-Connector To install USB 3.1 Gen 2 connector USB 3.1 Gen 2 This connector will only fit in one orientation. Push the connector until it clicks into place. To install USB 3.1 Gen 1 connector To install USB 2.0 connector USB 3.1 Gen 1...

  • Page 59: Expansion Card Installation

    2.1.8 Expansion card installation To install PCIe x16 cards To install PCIe x1 cards ROG RAMPAGE VI EXTREME...
  • Page 60 To install FAN EXTENSION CARD The illustrations in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. Chapter 2: Basic Installation 2-10...
  • Page 61 To install ThunderboltEX 3 card The illustrations in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. ROG RAMPAGE VI EXTREME 2-11...

  • Page 62: Installation

    2.1.9 M.2 installation Supported M.2 type varies per motherboard. Chapter 2: Basic Installation 2-12...

  • Page 63: Fan Bracket Installation

    2.1.10 Fan bracket installation To install the MOS FAN bracket When using high performance settings whilst overclocking, ensure to install the MOS FAN bracket for additional fan(s). Fans are purchased separately. ROG RAMPAGE VI EXTREME 2-13...
  • Page 64 To install the DIMM.2 FAN mount • You may install up to two 50mm x 50mm fans or a single 100mm x 100 mm fan. • Fans are purchased separately. Chapter 2: Basic Installation 2-14...

  • Page 65: Wi-Fi Antenna Installation

    2.1.11 Wi-Fi antenna installation Installing the ASUS 2x2 dual band W-Fi and ASUS Wi-Fi 802.11ad(WiGig) antenna Connect the bundled ASUS 2x2 dual band Wi-Fi antenna connector to the top two Wi-Fi ports at the back of the chassis, then connect the Wi-Fi 802.11ad(WiGig) antenna to the bottom Wi-Fi port. ASUS 2x2 dual band W-Fi antenna ASUS Wi-Fi 802.11ad(WiGig) antenna • Ensure that the ASUS 2x2 dual band W-Fi and ASUS Wi-Fi 802.11ad(WiGig) antenna is securely installed to the Wi-Fi ports. •...

  • Page 66: Bios Update Utility

    BIOS Flashback is not operating properly. This may be caused by improper installation of the USB storage device and filename/file format error. If this scenario happens, please restart the system to turn off the light. • Updating BIOS may have risks. If the BIOS program is damaged during the process and results to the system’s failure to boot up, please contact your local ASUS Service Center. Chapter 2: Basic Installation 2-16...

  • Page 67: Motherboard Rear And Audio Connections

    * and ** : Refer to the tables on the next page for LAN port LEDs, and audio port definitions. • USB 3.1 Gen 1/Gen 2 devices can only be used as data storage only. • We strongly recommend that you connect your devices to ports with matching data transfer rate. Please connect your USB 3.1 Gen 1 devices to USB 3.1 Gen 1 ports and your USB 3.1 Gen 2 devices to USB 3.1 Gen 2 ports for faster and better performance for your devices. • Due to the design of the Intel chipset, all USB devices connected to the USB 3.1 Gen 1 ports are controlled by the xHCI controller. Some legacy USB devices must update their firmware for better compatibility. • When KeyBot II is activated, USB hot plug function of the KeyBot port (USB 3.1 Gen 1 port 5) will be temporarily disabled. ROG RAMPAGE VI EXTREME 2-17...
  • Page 68 * LAN port LED indications Activity Link LED Speed LED Status Description Status Description ACT/LINK SPEED No link 10 Mbps connection Orange Linked Orange 100 Mbps connection Orange (Blinking) Data activity Green 1 Gbps connection Orange (Blinking Ready to wake up LAN port then steady) from S5 mode You can disable the LAN controllers in BIOS. Due to hardware design, the LAN1 port’s...

  • Page 69: Audio I/O Connections

    2.3.2 Audio I/O connections Audio I/O ports Connect to Headphone and Mic Connect to Stereo Speakers Connect to 2 Speakers ROG RAMPAGE VI EXTREME 2-19...
  • Page 70 Connect to 4 Speakers Connect to 6 Speakers Connect to 8 Speakers Chapter 2: Basic Installation 2-20...

  • Page 71: Starting Up For The First Time

    While the system is ON, press the power button for less than four seconds to put the system on sleep mode or soft-off mode, depending on the BIOS setting. Press the power switch for more than four seconds to let the system enter the soft-off mode regardless of the BIOS setting. ROG RAMPAGE VI EXTREME 2-21...
  • Page 72 Chapter 2: Basic Installation 2-22...

  • Page 73: Chapter 3: Bios Setup

    BIOS Setup Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboard- only BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system.

  • Page 74: Bios Setup Program

    RTC RAM via the Clear CMOS button. • The BIOS setup program does not support the Bluetooth devices. Please visit ASUS website for the detailed BIOS content manual. BIOS menu screen The BIOS Setup program can be used under two modes: EZ Mode and Advanced Mode.

  • Page 75: Advanced Mode

    Menu bar Language MyFavorite(F3) Qfan Control(F6) EZ Tuning Wizard(F11) Hot Keys Go back to EZ Mode Last modified settings Menu items General help Search on the FAQ Displays the CPU temperature, CPU, and memory voltage output ROG RAMPAGE VI EXTREME...

  • Page 76: Menu Bar

    Menu bar The menu bar on top of the screen has the following main items: For saving the frequently-used system settings and configuration. My Favorites For changing the basic system configuration Main For changing the overclocking settings Extreme Tweaker For changing the advanced system settings Advanced For displaying the system temperature, power status, and changing Monitor...

  • Page 77: Hot Keys

    Move your mouse over this button to show a QR code, scan this QR code on your mobile device to connect to the BIOS FAQ web page of the ASUS support website. You can also scan the following QR code: Hot keys This button above the menu bar contains the navigation keys for the BIOS setup program.

  • Page 78: Ez Mode

    3.2.2 EZ Mode The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance, mode and boot device priority. To access the Advanced Mode, select Advanced Mode or press the <F7> hotkey for the advanced BIOS settings.

  • Page 79: Q-Fan Control

    Click to activate DC Mode configured PWM Mode Select a profile to apply to Click to apply the fan setting your fans Click to undo the Click to go back to main menu changes Select to manually configure your fans ROG RAMPAGE VI EXTREME...
  • Page 80 Configuring fans manually Select Manual from the list of profiles to manually configure your fans’ operating speed. Speed points Select to manually configure your fans To configure your fans: Select the fan that you want to configure and to view its current status. Click and drag the speed points to adjust the fans’...

  • Page 81: Ez Tuning Wizard

    To start OC Tuning: Press <F11> on your keyboard or click from the BIOS screen to open EZ Tuning Wizard screen. Click OC then click Next. Select a PC scenario Daily Computing or Gaming/Media Editing, then click Next. ROG RAMPAGE VI EXTREME...

  • Page 82: Creating Raid

    Select a Main Cooling System BOX cooler, Tower cooler, Water cooler, or I’m not sure, then click Next. After selecting the Main Cooling System, click Next then click Yes to start the OC Tuning. Creating RAID To create RAID: Press <F11> on your keyboard or click from the BIOS screen to open EZ Tuning Wizard screen.
  • Page 83 After selecting the type of RAID, click Next then click Yes to continue the RAID setup. After the RAID setup is done, click Yes to exit the setup then click OK to reset your system. ROG RAMPAGE VI EXTREME 3-11...

  • Page 84: My Favorites

    My Favorites My Favorites is your personal space where you can easily save and access your favorite BIOS items. My Favorites comes with several performance, power saving, and fast boot related items by default. You can personalize this screen by adding or removing items. Chapter 3: BIOS Setup 3-12...
  • Page 85 Configuration items such as Memory SPD Information, system time and date. Click Exit (ESC) or press <Esc> key to close Setup Tree Map screen. Go to My Favorites menu to view the saved BIOS items. ROG RAMPAGE VI EXTREME 3-13...

  • Page 86: Main Menu

    Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security The Security menu items allow you to change the system security settings.
  • Page 87 ASUS MultiCore Enhancement [Auto] This item allows you to maximize the oveclocking performance optimized by ASUS core ratio settings. [Disabled] This item allows you to set to default core ratio settings. CPU Core Ratio This item allows you to set the CPU core ratios.

  • Page 88: Advanced Menu

    Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. 3.6.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects.

  • Page 89: Pch Configuration

    This item allows you to enable or disable the selected SATA port. Configuration options: [Disabled] [Enabled] Hot Plug These items appears only when the SATA Mode Selection is set to [AHCI] and allows you to enable or disable SATA Hot Plug Support. Configuration options: [Disabled] [Enabled] ROG RAMPAGE VI EXTREME 3-17...

  • Page 90: Rog Effects

    3.6.6 ROG Effects The items in this menu allow you to configure the LEDs on your motherboard. Onboard LED This item allows you to enable all the onboard LEDs. Configuration options: [Enabled] [Disabled] 3.6.7 CPU Storage Configuration The items in this menu allow you to configure CPU storage configurations. Due to CPU behavior, CPU RAID functions with Intel CPU RSTe only supports Intel ®...

  • Page 91: Apm Configuration

    The items in this menu allow you to configure Ipv4 / Ipv6 PXE support. 3.6.11 HDD/SSD SMART Information This menu displays the SMART information of the connected devices. NVM Express devices do not support SMART information. ROG RAMPAGE VI EXTREME 3-19...

  • Page 92: Usb Configuration

    3.6.12 USB Configuration The items in this menu allow you to change the USB-related features. The Mass Storage Devices item shows the auto-detected values. If no USB device is detected, the item shows None. USB Single Port Control This item allows you to enable or disable the individual USB ports. Refer to section 1.1.2 Motherboard layout for the location of the USB ports.

  • Page 93: Boot Menu

    Configuration options: [UEFI and Legacy OPROM] [Legacy OPROM only] [UEFI only] Boot from Network Devices This item allows you to select the type of network devices that you want to launch. Configuration options: [Ignore] [Legacy only] [UEFI driver first] ROG RAMPAGE VI EXTREME 3-21...

  • Page 94: Tool Menu

    3.9.1 ASUS EZ Flash 3 Utility This item allows you to run ASUS EZ Flash 3. When you press <Enter>, a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to confirm your choice.

  • Page 95: Secure Erase

    To launch Secure Erase, click Tool > Secure Erase on the Advanced mode menu. Check the ASUS support site for a full list of SSDs tested with Secure Erase. The drive may become unstable if you run Secure Erase on an incompatible SSD.

  • Page 96: Asus Overclocking Profile

    3.9.3 ASUS Overclocking Profile This item allows you to store or load multiple BIOS settings. Load from Profile This item allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your BIOS settings, press <Enter>, and then select Yes.

  • Page 97: Asus Spd Information

    This item displays the information and recommended configuration for the PCIE slots that the graphics card is installed in your system. This feature is only supported on selected ASUS graphics cards. Bus Interface This item allows you to select the bus interface.

  • Page 98: Updating Bios

    3.11 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility,and performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS.

  • Page 99: Asus Ez Flash 3

    3.11.2 ASUS EZ Flash 3 ASUS EZ Flash 3 allows you to download and update to the latest BIOS through the Internet without having to use a bootable floppy disk or an OS-based utility. Updating through the Internet varies per region and Internet conditions. Check your local Internet connection before updating through the Internet.
  • Page 100 To update the BIOS by Internet: Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash 3 Utility and press <Enter>. Select via Internet. Press the Left/Right arrow keys to select an Internet connection method, and then press <Enter>.

  • Page 101: Asus Crashfree Bios 3

    3.11.3 ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using the motherboard support USB drive that contains the BIOS file.
  • Page 102 Chapter 3: BIOS Setup 3-30...

  • Page 103: Raid Support

    With the RAID 10 configuration you get all the benefits of both RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive and three new drives for this setup. ROG RAMPAGE VI EXTREME...

  • Page 104: Installing Storage Devices

    4.1.2 Installing storage devices The motherboard supports Serial ATA hard disk drives and PCIE SSD storage devices. For optimal performance, install identical drives of the same model and capacity when creating a disk array. Refer to Chapter 2 for details on installing storage devices to your motherboard. 4.1.3 Intel Rapid Storage Technology in UEFI BIOS...
  • Page 105 When the RAID Level item is selected, press <Enter> to select the RAID level to create, and then press <Enter>. Under Select Disks, press <Enter> and select X for the disks you want to include in the RAID set. ROG RAMPAGE VI EXTREME...
  • Page 106 When the Strip Size item is selected, press <Enter> to select strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size values range from 4 KB to 128 KB. The following are typical values: RAID 0: 128 KB RAID 10: 64 KB...
  • Page 107 <Enter>. The following screen appears: When the Delete item is selected, press <Enter>, then select Yes to delete the RAID volume and return to the Intel Rapid Storage Technology menu, or select No to ® cancel. ROG RAMPAGE VI EXTREME...

  • Page 108: Intel ® Virtual Raid On Cpu In Uefi Bios

    4.1.4 Intel Virtual Raid on CPU in UEFI BIOS ® The CPU RAID functions of RAID 1, RAID 5, and RAID 10 require a KEY module and Intel ® CPU RSTe to be enabled. • The KEY module is purchased separately. •...
  • Page 109 When the Enable RAID spanned over VMD Controllers item is selected, press <Enter> and select X to enable this function. Under Select Disks, press <Enter> and select X for the disks you want to include in the RAID set. ROG RAMPAGE VI EXTREME...
  • Page 110 When the Strip Size item is selected, press <Enter> to select strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size values range from 4 KB to 128 KB. The following are typical values: RAID 0: 128 KB RAID 10: 64 KB...
  • Page 111 <Enter>. The following screen appears: When the Delete item is selected, press <Enter>, then select Yes to delete the RAID volume and return to the Intel Virtual Raid on CPU menu, or select No to cancel. ® ROG RAMPAGE VI EXTREME...
  • Page 112 Installing the RAID controller driver during Windows 10 OS installation ® After creating the RAID sets, you are now ready to install an operating system to the independent drives or bootable array. This part provides the instructions on how to install the RAID controller drivers during OS installation.
  • Page 113 Select the RAID controller driver you need from the list and click Next. When the system finishes loading the RAID driver, select the drive to install Windows and click Next. Setup then proceeds with the OS installation. Follow screen instructions to continue. ROG RAMPAGE VI EXTREME 4-11...

  • Page 114: Intel ® Rapid Storage Technology Option Rom Utility

    4.1.5 Intel Rapid Storage Technology Option ROM utility ® To enter the Intel Rapid Storage Technology Option ROM utility: ® Turn on the system. During POST, press <Ctrl> + <I> to display the utility main menu. RAID Volumes: None defined. Physical Devices: Port Device Model...
  • Page 115 Size Status ST3160812AS 9LS0HJA4 149.0GB Non-RAID Disk ST3160812AS 9LS0F4HL 149.0GB Non-RAID Disk ST3160812AS 3LS0JYL8 149.0GB Non-RAID Disk ST3160812AS 9LS0BJ5H 149.0GB Non-RAID Disk Select 2 to 6 to use in creating the volume. [↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done ROG RAMPAGE VI EXTREME 4-13...
  • Page 116 Use the up/down arrow key to select a drive, and then press <Space> to select. A small triangle marks the selected drive. Press <Enter> after completing your selection. Use the up/down arrow key to select the strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>.
  • Page 117 (This does not apply to Recovery volumes) Are you sure you want to delete “Volume0”? (Y/N): Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to return to the DELETE VOLUME menu. ROG RAMPAGE VI EXTREME 4-15...

  • Page 118: Creating A Raid Driver Disk

    Exiting the Intel Rapid Storage Technology Option ROM utility ® To exit the utility: From the utility main menu, select 6. Exit, then press <Enter>. The following warning message appears: [CONFIRM EXIT] Are you sure you want to exit? (Y/N): Press <Y>...

  • Page 119: Appendix

    Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ROG RAMPAGE VI EXTREME...
  • Page 120 Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This Class B digital apparatus complies with Canadian ICES-003, RSS-210, and CAN ICES- 3(B)/NMB-3(B). This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 121 ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials.
  • Page 122 FCC Bluetooth Wireless Compliance The antenna used with this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter subject to the conditions of the FCC Grant. Bluetooth Industry Canada Statement This Class B device meets all requirements of the Canadian interference-causing equipment regulations.
  • Page 123 ASUSTek Computer Inc. hereby declares that this device is in compliance zahtjevima i ostalim odgovarajućim odredbama direktive 2014/53/EU. Cijeli with the essential requirements and other relevant provisions of Directive tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/ 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/ WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit će ograničen na...
  • Page 124 Direktive 2014/53/EU. Polno https://www.asus.com/support/ besedilo izjave EU o skladnosti je na voljo na https://www.asus.com/support/ Wi-Fi darbība 5150–5350 MHz ir jāierobežo lietošanai telpās valstīs, kuras WiFi, ki deluje v pasovnem območju 5150–5350 MHz, mora biti v državah, norādītas tālāk.
  • Page 125 інсталяцією просто неба для країн, поданих у таблиці нижче. QCA9008-TBD1 output power table: Function Frequency Maximum Output Power (EIRP) 2412-2472 MHz 18 dBm WiFi 5150-5350 MHz 21 dBm 5470-5725 MHz 19 dBm WiGig 58.32-62.64 GHz 27 dBm Bluetooth 2402-2480 MHz 8 dBm ROG RAMPAGE VI EXTREME...

  • Page 126: Asus Contact Information

    +1-510-739-3777 +1-510-608-4555 Web site http://www.asus.com/us/ Technical Support Support fax +1-812-284-0883 Telephone +1-812-282-2787 Online support http://qr.asus.com/techserv ASUS COMPUTER GmbH (Germany and Austria) Address Harkort Str. 21-23, 40880 Ratingen, Germany +49-2102-959931 Web site http://www.asus.com/de Online contact http://eu-rma.asus.com/sales Technical Support Telephone +49-2102-5789555 Support Fax...

  • Page 127: Declaration Of Conformity

    CA 94539. Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Motherboard Model Number : ROG RAMPAGE VI EXTREME Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the...
  • Page 128 Appendix A-10...

Table of Contents