Setting The Button Operation Mode; Setting The Operation Mode Of The [All] Button In The Transition Control Block - Sony MVS-8000X User Manual

Setting the Button Operation Mode

1
In the Panel >Operation menu, press [Custom Button].
The Custom Button menu appears.
The status area shows a list of the items with their
settings.
2
Make the following settings as required.
Operation mode during an auto transition: For the
operation mode when the [AUTO TRANS] or
[TAKE] button is pressed once more during an
auto transition, select [Continue] or [Cancel] in the
<Auto Trans/Take> group.
• Continue: Continue the auto transition.
• Cancel: Cancel the auto transition and return to
the state before starting the auto transition.
Operation mode during keyframe execution: For
the operation mode when the [RUN] button is
pressed once more during effect execution, select
[Continue] or [Cancel] in the <Run> group.
• Continue: Continue the execution.
• Cancel: Cancel the execution and return to the
state before starting the execution.
Status display for auto transition execution button:
When the [AUTO TRANS] or [TAKE] button is
pressed to carry out an auto transition, select how
the button is lit or off in the <Auto Trans/Take Key
On Stats> group.
• Disable: Lights amber during the transition, and
goes off at the end of the transition.
• Enable: Lights green during the transition, and
at the end of the transition lights red if on air and
amber if not on air.
Notes
This setting is only valid in the independent key
transition execution section of the following
control block.
• Downstream key control block (MKS-8032
DSK Fader Module, option)
Interchanging the [AUTO TRANS] and [CUT]
buttons: To interchange the [AUTO TRANS] and
[CUT] buttons in the transition control block,
press the [Auto Trans/Cut Swap] button, turning it
on.
Transition preview operation mode: For the
operation mode of the [TRANS PVW] button,
select [Lock] or [Hold] in the <Trans Pvw> group.
The setting as to whether to use the "One-time
mode" in which the transition preview terminates
when the transition completes, or to use button
control, is made on the switcher side (see page
536).
520
Operation Settings (Operation Menu)
[KEY] button operation mode for key source bus
operations: For key source bus operations,
specify the operation mode of the [KEY] button in
the auxiliary bus control block in the <Key Source
Bus Select Mode> group, as follows.
• Key: If you select this, the [KEY] button is
always unlit, and this mode allows only key
signals to be selected with the cross-point
buttons.
• Video & Key: The [KEY] button is enabled,
and either video or key signals can be selected.
CCP-9000A-specific button settings: Press [CCP-
9000 Button], and skip to step 3.
3
If required, make the following settings.
DME channel selection mode: To set the mode when
one of the [DME1] to [DME4] buttons in the key
delegation section is pressed to select the DME
channel, select either of the following in the
<DME Select> group.
• Override: Forcibly select the selected channel.
(Later selection takes precedence).
• Pre Select: It is not possible to select a channel
that has already been otherwise selected.
(Earlier selection takes precedence.)
Operation mode of the [XPT HOLD] button in the
key delegation section: To set the operation mode
of the [XPT HOLD] button in the key delegation
section, select either of the following in the <Xpt
Hold> group.
• A/B Bus: When the [XPT HOLD] button is
pressed, turning it on, cross-point hold is
enabled for the A and B buses only.
• All Bus: When the [XPT HOLD] button is
pressed, turning it on, cross-point hold is
enabled for all buses used on the bank being
currently operated.
(A/B buses, Key 1 to Key 8 buses, Utility 1/2
buses, external DME bus, DME Utility 1/2
buses)
Setting the Operation Mode of the
[ALL] Button in the Transition
Control Block
Specify the next transition selected by pressing the [ALL]
button in the transition control block.
Notes
If everything here is set to Off, then pressing the [ALL]
button does not change the specification of the next
transition.