Sony RHT-G2000 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Speakers
  5. RHT-G2000 - Home Theater Built-in Sound Rack...
  6. Service manual
Sony RHT-G2000 Service Manual

Sony RHT-G2000 Service Manual

Theatre stand system
Hide thumbs Also See for RHT-G2000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Instructions
SERVICE MANUAL
Ver. 1.1 2006.04
This system incorporates Dolby* Digital and Pro Logic Surround and
the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories.
** "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems,
Inc.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With 4 ohm loads, both channels driven, from 200 – 20,000 Hz; rated
40 watts per channel minimum RMS power, with no more than 0.7 %
total harmonic distortion from 250 milli watts to rated output.
Amplifier section
Surround mode (reference)
* Depending on the sound field settings and the source, there may
be no sound output.
Inputs (Analog)
TV, SAT, DVD,
VIDEO 1, VIDEO 2
Inputs (Digital)
TV, SAT, DVD, VIDEO 1,
VIDEO 2 (Coaxial)
Tuner section
System
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Sony Corporation
9-879-844-02
Home Audio Division
2006D02-1
Published by Sony Techno Create Corporation
© 2006.04
SPECIFICATIONS
power output
Front: 100 W + 100 W 4 ohms
Center*: 100 W 4 ohms
Surround*: 100 W + 100 W 4 ohms
Subwoofer*: 200 W 2 ohms
Sensitivity: 610 mV
Impedance: 25 kilohms
Impedance: 75 ohms
PLL quartz-locked digital synthesizer
system
87.5 – 108.0 MHz (100 kHz step)
FM wire antenna
75 ohms, unbalanced
10.7 MHz
530 – 1,710 kHz
(with the interval set at 10 kHz)
531 – 1,710 kHz
(with the interval set at 9 kHz)
RHT-G2000
Antenna
AM loop antenna
Intermediate frequency
450 kHz
Video section
Inputs/Outputs
Video: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
/C
B
Accepts 480i/480p/720p/1080i
Speakers
Front
Speaker system
Bass reflex, magnetically shielded
Speaker unit
65 mm (2
Center
Speaker system
Bass reflex, magnetically shielded
Speaker unit
65 mm (2
Surround
Speaker system
Bass reflex, magnetically shielded
Speaker unit
65 mm (2
Subwoofer
Speaker system
Bass reflex, magnetically shielded
Speaker unit
160 mm (6
THEATRE STAND SYSTEM
US Model
Canadian Model
, P
/C
: 0.7 Vp-p 75 ohms
B
R
R
5
/
inches) cone type
8
5
/
inches) cone type
8
inches) cone type × 2
5
/
8
inches) cone type × 2
3
/
8
– Continued on next page –

Advertisement

Table of Contents
loading

Related Manuals for Sony RHT-G2000

Summary of Contents for Sony RHT-G2000

  • Page 1 530 – 1,710 kHz (with the interval set at 10 kHz) THEATRE STAND SYSTEM 531 – 1,710 kHz (with the interval set at 9 kHz) Sony Corporation 9-879-844-02 Home Audio Division 2006D02-1 Published by Sony Techno Create Corporation © 2006.04...
  • Page 2 LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Table Of Contents

    RHT-G2000 SAFETY CHECK-OUT TABLE OF CONTENTS After correcting the original service problem, perform the following GENERAL ..............4 safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, DISASSEMBLY and all other exposed metal parts for AC leakage. Check leakage as 2-1.

  • Page 4: General

    RHT-G2000 SECTION 1 This section is extracted from instruction manual. GENERAL LOCATING THE CONTROLS Index to Parts and Controls For more information, refer to the pages indicated in parentheses. Front panel A Front panel display D INPUT SELECTOR B Sound field indicator (remote sensor) C VOLUME +/–...

  • Page 5: Rear Panel

    RHT-G2000 Rear panel Remote control Here describes the buttons for amplifier operation only. See ANTENNA page 12 for the buttons for operation of the connected COAXIAL components. SPEAKERS TV ?/1 AV ?/1 RM SETUP SYSTEM STANDBY MODE SURROUND VIDEO1 VIDEO2 5.1CH...

  • Page 6: Disassembly

    RHT-G2000 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. AMP ASSY 2 two rivets 3 two shafts (lock) 1 screw (wood +R4.1X16) 5 AMP assy...

  • Page 7: Test Mode

    RHT-G2000 SECTION 3 TEST MODE 1. Starting Test Mode 5-3. Version Check • Please start the test mode by the following procedure when Procedure: you execute “Volume Test’’ or “Panel Test’’. 1. Press the VOLUME + button with all segment lit, and Procedure: “RACK”...

  • Page 8: Diagrams

    RHT-G2000 SECTION 4 DIAGRAMS • Note for Printed Wiring Boards and Schematic Diagrams Note on Printed Wiring Boards. Note on Schematic Diagrams. • All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side •...

  • Page 9: Block Diagram -Video Section

    RHT-G2000 4-1. BLOCK DIAGRAM –VIDEO SECTION– J101 (1/2) IC202 /B-Y IC203 VIDEO SWITCH VIDEO AMP /R-Y COMPOSITE J101 (1/2) VIDEO IN VIDEO OUT COMPONENT /B-Y VIDEO OUT J101 (1/2) /R-Y /B-Y AV SEL0-3 /R-Y SECTION (Page 10) COMPOSITE VIDEO IN...

  • Page 10: Dsp Section

    RHT-G2000 –DSP SECTION– FM/AM TUNER UNIT J101(2/2) COAXIAL FM ANT L-CH R-CH ANALOG IN 75Ω IC512 IC518 DIGITAL AUDIO DELAY IC506 AM ANT IC507 SELCTOR DIGITAL AUDIO SD-RAM PROCESSOR IC101 TUDI 72-75 OPTICAL IN Q101 7-10 OPTICAL TUDO 77-80 DIGITAL...

  • Page 11: Audio Section

    RHT-G2000 – AUDIO SECTION– IC108 STREAM PROCESSOR IC101 POWER DRIVER D1 – D3, MCKO, BCKO, LRCKO 31 DATA OUTR1 2 PWMBP OUTB SECTION FRONT MCKO (Page 10) 36 XFSIIN (–) OUTR2 PWMAP OUTA BCKO 30 BCK RESET LRCKO OUTL1 29 LRCK •...

  • Page 12: Power Section

    RHT-G2000 –POWER SECTION– T901 D901 TRANSFORMER(MAIN) AC IN D931 IC901 D905 +31.5V Q901 AC/DC DC/DC POWER CONVERTER CONVERTER ON/OFF IC931 T801 VOLTAGE DETECT PC901 TO FLUORESCENT PHOTO RECT INDICATOR TUBE COUPLER D801,802 D804,805 Q943,947 PC903 Q801 POWER PHOTO CONTROL COUPLER...

  • Page 13: Printed Wiring Board - Main Board (Side A)

    RHT-G2000 4-2. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) – • See page 33 for Circuit Boards Location. :Uses unleaded solder. MAIN BOARD (SIDE A) • Semiconductor Location Ref. No. Location D503 D507 D914 F-10 D915 F-10 D925 I-10...

  • Page 14: Printed Wiring Board - Main Board (Side B)

    RHT-G2000 4-3. PRINTED WIRING BOARD – MAIN BOARD (SIDE B) – :Uses unleaded solder. • See page 33 for Circuit Boards Location. • Semiconductor Location SPOUT SPOUT BOARD BOARD (Page 29) (Page 29) Ref. No. Location MAIN BOARD (SIDE B)

  • Page 15: Schematic Diagram - Main Board (1/8)

    RHT-G2000 4-4. SCHEMATIC DIAGRAM – MAIN BOARD (1/8) – • See page 35 for IC Block Diagrams. RHT-G2000...

  • Page 16: Schematic Diagram - Main Board (2/8)

    RHT-G2000 4-5. SCHEMATIC DIAGRAM – MAIN BOARD (2/8) – • See page 34 for IC Block Diagrams. RHT-G2000...

  • Page 17: Schematic Diagram - Main Board (3/8)

    RHT-G2000 4-6. SCHEMATIC DIAGRAM – MAIN BOARD (3/8) – • See page 8 for Waveforms. • See page 35 for IC Block Diagrams. RHT-G2000...

  • Page 18: Schematic Diagram - Main Board (4/8)

    RHT-G2000 • See page 34 for IC Block Diagrams. 4-7. SCHEMATIC DIAGRAM – MAIN BOARD (4/8) – RHT-G2000...

  • Page 19: Schematic Diagram - Main Board (5/8)

    RHT-G2000 4-8. SCHEMATIC DIAGRAM – MAIN BOARD (5/8) – • See page 8 for Waveforms. • See page 39 for IC Pin Function Description. RHT-G2000...

  • Page 20: Schematic Diagram - Main Board (6/8)

    RHT-G2000 • See page 8 for Waveforms. • See page 35, 36 for IC Block Diagrams. 4-9. SCHEMATIC DIAGRAM – MAIN BOARD (6/8) – RHT-G2000...

  • Page 21: Schematic Diagram - Main Board (7/8)

    RHT-G2000 4-10. SCHEMATIC DIAGRAM – MAIN BOARD (7/8) – • See page 8 for Waveforms. RHT-G2000...

  • Page 22: Schematic Diagram - Main Board (8/8)

    RHT-G2000 4-11. SCHEMATIC DIAGRAM – MAIN BOARD (8/8) – RHT-G2000...

  • Page 23: Printed Wiring Board - Io Board (Side A)

    RHT-G2000 4-12. PRINTED WIRING BOARD – IO BOARD (SIDE A) – :Uses unleaded solder. • See page 33 for Circuit Boards Location. IO BOARD (SIDE A) • Semiconductor Location Ref. No. Location D201 D202 D203 D204 D205 D206 D207 D208...

  • Page 24: Printed Wiring Board - Io Board (Side B)

    RHT-G2000 4-13. PRINTED WIRING BOARD – IO BOARD (SIDE B) – • See page 33 for Circuit Boards Location. :Uses unleaded solder. • Semiconductor AUDIO VIDEO INPUT Location Ref. No. Location VIDEO 1 VIDEO 2 D213 IO BOARD (SIDE B)

  • Page 25: Schematic Diagram - Io Board

    RHT-G2000 4-14. SCHEMATIC DIAGRAM – IO BOARD – • See page 36, 37 for IC Block Diagrams. RHT-G2000...

  • Page 26: Printed Wiring Board - Panel Section (Side A)

    RHT-G2000 4-15. PRINTED WIRING BOARD – PANEL SECTION (SIDE A) – :Uses unleaded solder. • See page 33 for Circuit Boards Location. (SIDE A) PANEL BOARD AUTO VIRTUAL NEWS 1-867-288- (11) (SIDE A) BOARD • Semiconductor Location Ref. No. Location...

  • Page 27: Printed Wiring Board - Panel Section (Side B)

    RHT-G2000 4-16. PRINTED WIRING BOARD – PANEL SECTION (SIDE B) – • See page 33 for Circuit Boards Location. :Uses unleaded solder. (SIDE B) PANEL BOARD INPUT SELECTOR VOLUME – 1-867-288- (11) (SIDE B) BOARD • Semiconductor Location Ref. No.

  • Page 28: Schematic Diagram - Panel Section

    RHT-G2000 • See page 38 for IC Block Diagrams. 4-17. SCHEMATIC DIAGRAM – PANEL SECTION – RHT-G2000...

  • Page 29: Printed Wiring Board - In/Out/Power Section

    RHT-G2000 4-18. PRINTED WIRING BOARD – IN/OUT/POWER SECTION – • See page 33 for Circuit Boards Location. :Uses unleaded solder. BOARD BOARD SPEAKER SURROUND BACK EXTSP BOARD 1-867-401- 1-867-401- (11) (11) ACIN BOARD MODE FRONT 5.1CH MAIN BOARD (Page 14)

  • Page 30: Schematic Diagram - In/Out/Power Section

    RHT-G2000 4-19. SCHEMATIC DIAGRAM – IN/OUT/POWER SECTION – RHT-G2000...

  • Page 31: Printed Wiring Board - Input Box Section

    RHT-G2000 4-20. PRINTED WIRING BOARD – INPUT BOX SECTION – :Uses unleaded solder. • See page 33 for Circuit Boards Location. INPUT1 BOARD INPUT2 BOARD ANALOG ANALOG /R-Y COMPONENT /B-Y VIDEO IN VIDEO IN VIDEO IN COAX COAX DIGITAL IN...

  • Page 32: Schematic Diagram - Input Box Section

    RHT-G2000 4-21. SCHEMATIC DIAGRAM – INPUT BOX SECTION – RHT-G2000...
  • Page 33 RHT-G2000 • Circuit Boards Location AC2 board ACIN board MAIN board TVI/O board CNV board IO board PANEL board SPOUT board EXTSP board INPUT1 board INPUT2 board...

  • Page 34: Main Board

    RHT-G2000 • IC Block Diagrams – MAIN BOARD – IC101-107 CXD9775M GVDD B GVDD GVDD B BST B DVDD DREG DREG GND 1 PVDD B GATE PVDD B PWM BP 2 RECEIVER DRIVE OUT B TIMING GND 3 OUT B...
  • Page 35 RHT-G2000 IC108-110 CXD9843AR 41 40 39 38 37 Sampling Rate Converter Filter Liner ∆ ∑ Converter & Gain Interpolator Control Filter XFSIIN DVDD Clock Generator Clock Generator (Secondary Clock System) (Primary Clock System) INIT/MUTE Serial Control TEST BFVSS BFVDD 9 10 11 12 13 14 15 16 17 18 19 20...
  • Page 36 RHT-G2000 IC512 NJU26902VM1-TE2 RESETb 20 VDD 19 VDD SERIAL SERIAL AUDIO AUDIO 18 SDO INTERFACE INTERFACE DELAY 17 FS COUNT(2) 16 BYPASS COUNT(3) L/R IN L/R OUT 15 SDO_OD BCKI COUNT(4) 14 COUNT(1) COUNT(5) 13 MODE(1) CONTROL LOGIC 12 COUNT(0) 11 MODE(0) –...
  • Page 37 RHT-G2000 IC201 NJM2585M (TE2) CH1 IN1 CONT1 BIAS 75Ω 24 CH1 OUT Driver SW CONTROL 1 23 POWER SAVE CH1 IN2 CONT1 BIAS 75Ω CONT2 22 CH2 OUT Driver SW CONTROL 2 21 V+2 CH1 IN3 CONT1 BIAS 75Ω 20 CH3 OUT...
  • Page 38 RHT-G2000 IC842 ML9208-03MBZ03B SEG4 SEGMENT DRIVER SEG21 SEG3 SEG22 CGROM SEG2 248w X 35b DCRAM SEG23 SEG1 16w X 8b CGRAM 8w X 35b SEG24 ADRAM 16w X 2b SEG25 ADDRESS DRIVER SELECTOR SEG26 SEG27 READ WRITE PORT ADDRESS ADDRESS...
  • Page 39 RHT-G2000 • IC Pin Function Description MAIN BOARD IC509 M30622MEP-A52FPU0 (SYSTEM CONTROLLER) Pin No. Pin name Description DAMP SCDT/ Digital amp (IC108 to 110) data output DIAT_SDATA DAMP SHIFT/ Digital amp (IC108 to 110) data output DIAT_SCLK XSCEN Not used...
  • Page 40 RHT-G2000 Pin No. Pin name Description LED1/CE Control of AUTO LED signal output DRIVE_RST(EN) Digital amp reset output DRIVE_OCP(DIAG) Digital amp (power driver) DIAG input OVERFLOW1 Over flow status1 of digital amp (IC108 to 110) input OVERFLOW2 Over flow status2 of digital amp (IC110) input...
  • Page 41 RHT-G2000 Pin No. Pin name Description MODEL Model select input KEY2 Key input 2 KEY1 Key input 1 — Ground terminal KEY0 Key input 0 VREF — Reference Voltage (+3.3V) — Power supply (+3.3V) M-ST/WMUTE LINK (multi STEREO) control output (not used)

  • Page 42: Exploded Views

    RHT-G2000 SECTION 5 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 may have some difference from the original number in the exploded views are not or dotted line with mark 0 are critical one.

  • Page 43: Panel Section

    RHT-G2000 5-2. PANEL SECTION not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-912-253-01 CATCHER A-1128-200-A PANEL BOARD, COMPLETE 1-826-128-11 LOUDSPEAKER (16cm) 3-087-053-01 +BVTP2.6 (3CR) 4-229-966-02 SCREW (4X16), +BV TAPPING 4-033-718-01 BUCKLE, B...

  • Page 44: Speaker Section

    RHT-G2000 5-3. SPEAKER SECTION not supplied not supplied #1 #4 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-826-244-11 SPEAKER (6cm) 2-249-250-00 CLIP (SMALL), CANOE 4-986-971-01 SCREW (3.5) A-1128-179-A SPEAKER ASSY, FR...

  • Page 45: Amp Section-1

    RHT-G2000 5-4. AMP SECTION-1 not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-531-576-01 RIVET 7-621-846-40 SCREW, WOOD +R 4.1X16...

  • Page 46: Amp Section-2

    RHT-G2000 5-5. AMP SECTION-2 not supplied 206 207 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-828-959-11 WIRE (FLAT TYPE) (9 CORE) * 207 3-703-244-00 BUSHING (2104), CORD 1-828-382-11 WIRE (FLAT TYPE) (23 CORE)

  • Page 47: Amp Section-3

    RHT-G2000 5-6. AMP SECTION-3 not supplied F901 not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-828-363-11 WIRE (FLAT TYPE) (19 CORE) (320mm) * 256 4-954-051-41 HOLDER, PC BOARD...

  • Page 48: Input Box Section

    RHT-G2000 Ver. 1.1 5-7. INPUT BOX SECTION not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1197-058-A INPUT BOX (A) ASSY 2-631-959-01 COVER (I/O A)

  • Page 49: Electrical Parts List

    RHT-G2000 SECTION 6 ACIN ELECTRICAL PARTS LIST EXTSP INPUT 1 NOTE: • Items marked “*” are not stocked since they • Due to standardization, replacements in the The components identified by mark 0 parts list may be different from the parts are seldom required for routine service.
  • Page 50 RHT-G2000 INPUT 1 INPUT 2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C105 1-164-156-11 CERAMIC CHIP 0.1uF J102 1-819-588-11 JACK, PIN 1P (COAX(DGITAL IN)) C106 1-164-156-11 CERAMIC CHIP 0.1uF < COIL > < CONNECTOR >...
  • Page 51 RHT-G2000 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C239 1-126-964-11 ELECT 10uF D211 8-719-067-40 DIODE STZ6.8N-T146 C240 1-126-933-11 ELECT 100uF D212 8-719-067-40 DIODE STZ6.8N-T146 C241 1-164-156-11 CERAMIC CHIP 0.1uF D213 8-719-067-40 DIODE STZ6.8N-T146 C242 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 52 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R215 1-218-285-11 METAL CHIP 1/10W R275 1-216-841-11 METAL CHIP 1/10W R216 1-216-833-11 METAL CHIP 1/10W R276 1-216-841-11 METAL CHIP 1/10W R217 1-216-833-11 METAL CHIP 1/10W R218...
  • Page 53 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C141 1-164-156-11 CERAMIC CHIP 0.1uF C209 1-125-898-91 CERAMIC CHIP 0.22uF C142 1-164-156-11 CERAMIC CHIP 0.1uF C210 1-125-898-91 CERAMIC CHIP 0.22uF C211 1-131-704-11 FILM C143 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 54 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C296 1-163-021-91 CERAMIC CHIP 0.01uF C403 1-162-927-11 CERAMIC CHIP 100PF C297 1-163-021-91 CERAMIC CHIP 0.01uF C404 1-162-927-11 CERAMIC CHIP 100PF C405 1-162-964-11 CERAMIC CHIP 0.001uF C298 1-163-021-91 CERAMIC CHIP 0.01uF...
  • Page 55 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C572 1-107-826-11 CERAMIC CHIP 0.1uF C942 1-126-965-11 ELECT 22uF C573 1-107-726-91 CERAMIC CHIP 0.01uF C943 1-126-933-11 ELECT 100uF C944 1-128-951-21 ELECT 2200uF C575 1-107-726-91 CERAMIC CHIP 0.01uF...
  • Page 56 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 D921 6-500-849-01 DIODE ERA22-08KFLB IC516 6-703-547-01 IC TA7805LS 0 D922 8-719-063-74 DIODE D1NL20U-TR2 IC518 8-759-546-74 IC TC7WH157FU (TE12R) 0 IC901 6-707-741-01 IC STR-F6138-LF1352 0 D923...
  • Page 57 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R154 1-216-864-11 SHORT CHIP R155 1-216-864-11 SHORT CHIP Q101 8-729-600-22 TRANSISTOR 2SA1235-F R156 1-216-864-11 SHORT CHIP Q102 8-729-600-22 TRANSISTOR 2SA1235-F Q103 8-729-600-22 TRANSISTOR 2SA1235-F...
  • Page 58 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R306 1-216-809-11 METAL CHIP 1/10W R396 1-216-809-11 METAL CHIP 1/10W R308 1-216-809-11 METAL CHIP 1/10W R400 1-216-845-11 METAL CHIP 100K 1/10W R309 1-216-809-11 METAL CHIP 1/10W...
  • Page 59 RHT-G2000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R507 1-216-809-11 METAL CHIP 1/10W R572 1-216-809-11 METAL CHIP 1/10W R508 1-216-809-11 METAL CHIP 1/10W R573 1-216-809-11 METAL CHIP 1/10W R510 1-216-809-11 METAL CHIP 1/10W R511...
  • Page 60 RHT-G2000 MAIN PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R726 1-216-821-11 METAL CHIP 1/10W R941 1-216-864-11 SHORT CHIP R728 1-216-821-11 METAL CHIP 1/10W R943 1-216-864-11 SHORT CHIP R729 1-216-829-11 METAL CHIP 4.7K 1/10W R730 1-216-829-11 METAL CHIP 4.7K...
  • Page 61 RHT-G2000 PANEL SPOUT Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C828 1-162-970-11 CERAMIC CHIP 0.01uF < RESISTOR > C829 1-124-261-00 ELECT 10uF R801 1-216-839-11 METAL CHIP 1/10W C851 1-162-960-11 CERAMIC CHIP 220PF R802 1-216-809-11 METAL CHIP...
  • Page 62 RHT-G2000 SPOUT TVI/O Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > < TRANSISTOR > D851 8-719-988-61 DIODE 1SS355TE-17 Q101 8-729-120-28 TRANSISTOR 2SC1623-L5L6 < TRANSISTOR > < RESISTOR > Q851 8-729-023-22 TRANSISTOR 2SD2114K R101...
  • Page 63 RHT-G2000 MEMO...

  • Page 64: Revision History

    RHT-G2000 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2005.08...

Table of Contents