Recording - Philips FW-V55 User Manual

VCD MINI HIFI SYSTEM
PROGRAM SHUFFLE
REPEAT TIMER REC
NEWS T.A. AM MW FM LW
60Hz 250Hz 500Hz
STANDBY
ON
CLOCK/ MP3•CD
TIMER CD1 • 2 • 3 BAND
VCD TUNER
PROG
SEARCH • TUNING
STOP•CLEAR
- ALBUM +
SOUND NAVIGATION
INCREDIBLE
SURROUND
DIGITAL
SOUND CONTROL
Notes:
– It is not possible to change tape side
during recording.
– If you do not intend to record via the
microphone, unplug the microphone to
avoid accidental mixing with other
recording source.
– For recording, use only tape of IEC type I
(normal tape) or IEC type II (Cr0 2 ).
– The tape is secured at both ends with
leader tape. At the beginning and end of
tape, nothing will be recorded for six to
seven seconds.
– The recording level is set automatically,
regardless of the position of Volume,
DBB, Incredible Surround or DSC.
– To prevent accidental recording, break
out the tab on the left shoulder of the
tape side you want to protect.
pg 01-28/V55/21-En 23
STEREO
BACK
FRONT HSD
1KHz 2KHz 4KHz 8KHz
PBC
RETURN
TAPE 1 • 2 CDR/VIDEO
TAPE AUX
A. REV
PRESET
PLAY PAUSE PREV SIDE NEXT
MIC
MP3-CD LEVEL
- TITLE +
DYNAMIC BASS
MIC
BOOST
– If " CHECK TAPE " is displayed, the
protection tab has been broken. Put a
piece of clear adhesive tape over the
opening. Do not cover the Cr0 2 tape
detection hole when covering the tab
opening.
Recording from other sources
(only on tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load a blank tape into tape deck 2 with
the open side downward.
3 Press í or ë to select the recording
tape side (see Tape Side under TAPE
section) .
4 Press VCD, TUNER or AUX.
• Start playback of the selected source.
5 Press REC to start recording.
™ The starts flashing.
REC
6 Press Ç to stop recording.
Notes:
– Only å å å å å or ∂ ∂ ∂ ∂ mode is available ∂
during recording .
– During recording, it is not possible to
listen to another source.
Dubbing tapes
(from tape deck 1 to
tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load the prerecorded tape into tape
deck 1 with full spool to the left and a
blank tape into tape deck 2 with full
spool aside.
3 Press í or ë to select the recording
tape side (see Tape Side under TAPE
section) .
6/8/01, 9:12 AM

RECORDING

4 Press DUB (HSD) once for normal
speed dubbing or twice (within 2
seconds) for high speed dubbing.
™ "NORMAL" (normal speed) or
"FAST" (high speed) will be
displayed, followed by "DUB" with
"< or >" scrolling left or right
depending on the tape side selected.
™ The appears on the display
HSD
during high speed dubbing.
• Dubbing will start immediately.
™ The starts flashing.
REC
5 Press Ç to stop dubbing.
Notes:
– Only å å å å å mode is available during
dubbing.
– At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 1 to tape deck 2.
– To ensure good dubbing, use tapes of
the same length.
– During high speed dubbing in Tape
mode, the sound is reduced to a low
volume.
– You can listen to another source while
dubbing.
3139 115 20042
23