GE c60 Instruction Manual page 496

Standards, certification
................................................................... 2-29
Status LEDs
............................................................................................. 4-19
Storage temperature
........................................................................ 2-27
Sub-harmonic stator ground fault, FlexLogic
Support, technical ................................................................................. 1-2
Surge immunity specifications
Synchrocheck
actual values ...................................................................................... 6-19
FlexLogic operands .......................................................................5-163
logic diagram ...................................................................................5-227
settings ...............................................................................................5-224
specifications ..................................................................................... 2-17
Synchrophasors
actual values .......................................................................... 6-21, 6-24
clearing PMU records ........................................................................ 7-2
commands ............................................................................................. 7-4
explained ...........................................................................................5-135
FlexLogic operands .......................................................................5-162
phasor measurement configuration ...... 5-140, 5-152, 5-154
phasor measurement unit calibration .................................5-144
phasor measurement unit recording ...................................5-151
test values .........................................................................................5-282
Syslog ......................................................................................................... 5-24
System frequency
.............................................................................5-117
System logs
............................................................................................ 5-24
System requirements
....................................................................... 3-43
System setup
.......................................................................................5-115
T
Target messages
................................................................................... 7-6
TARGET setting
........................................................................................ 5-5
Targets menu
........................................................................................... 7-6
TCP port number for web access
Technical support .................................................................................. 1-2
Teleprotection
actual values ......................................................................................... 6-4
clearing counters ................................................................................ 7-2
FlexLogic operands .......................................................................5-163
logic diagram ...................................................................................5-273
overview .............................................................................................5-272
settings ................................................................. 5-113, 5-272, 5-273
specifications ..................................................................................... 2-22
Temperature
FlexLogic monitor operand .......................................................5-165
monitor ................................................................................................. 7-10
operating and storage .................................................................. 2-27
Test voltages
......................................................................................... 3-10
Testing
force contact inputs .....................................................................5-281
force contact outputs ..................................................................5-281
lamp test ................................................................................................. 7-3
LEDs ........................................................................................................... 7-3
self-test error messages .................................................................. 7-7
settings ................................................................................ 5-279, 5-280
synchrophasors ..............................................................................5-282
x
..................5-162
.................................................... 2-28
.............................................. 5-73
TFTP
port, close ............................................................................................ 5-74
put cannot be done ......................................................................... 5-73
settings .................................................................................................. 5-73
Thermal demand characteristic
Thermal overload protection
logic diagram .................................................................................. 5-248
settings ............................................................................................... 5-245
specifications ..................................................................................... 2-17
Time
actual values .................................................................6-7, 6-23, 6-24
FlexLogic timer settings ............................................................. 5-172
operating .............................................................................................. 6-25
overwritten by external source ....................................................7-3
set ...............................................................................................................7-3
settings .................................................................................................. 5-82
Time overcurrent
see Phase, Neutral, and Ground TOCs
TOC
ground ................................................................................................ 5-191
neutral ................................................................................................ 5-188
phase .................................................................................................. 5-185
specifications ..................................................................................... 2-15
Torque for screws
............................................................................... 2-29
Traceability
data ........................................................................................................ 4-11
overview ............................................................................................... 4-10
rules ........................................................................................................ 4-12
view data .............................................................................................. 4-11
Tracking frequency
............................................................................ 6-20
Transducer I/O
actual values ...................................................................................... 6-22
settings ............................................................................................... 5-274
specifications ......................................................................... 2-21, 2-22
wiring ..................................................................................................... 3-21
Trip bus
FlexLogic operands ...................................................................... 5-164
logic diagram .................................................................................. 5-216
settings ............................................................................................... 5-214
Trip LEDs ................................................................................................... 5-95
Trouble indicator ....................................................................................7-7
Trouble LED
............................................................................................. 3-41
Troubleshooting
error messages ....................................................................................7-7
unit not programmed error ...................................................... 5-114
TxGOOSE
settings .................................................................................................. 5-47
U
UDP for TFTP
.......................................................................................... 5-73
UL certification
...................................................................................... 2-29
Unable to put relay in flash mode
Unauthorized access
commands .......................................................................................... 5-27
resetting ..................................................................................................7-2
C60 BREAKER PROTECTION SYSTEM – INSTRUCTION MANUAL
INDEX
................................................. 5-92
................................................9-4