1. Summary The keyboard is a univers al keyboard of s ecurity monitoring s eries , which can control the ball-type integrated camera of a ll kinds protocols matrix, which has been equipped with Joys tick which can control the revolving of the ca mera and the zoo m magnification of lens ; with the LCD s creen and the function of back-light;...
2.Keyboard Connection There is interface on the back of the keyboard, wh ich equipped with kinds of co mmunication Interface RS485 and infra red e mis s ion, which can connect with and control kinds of periphera l equipments . 2.1.
2. 3 Keyboard connection in the system Indirect control the dome when connect with matrix(as figure 2-4.1) 。contrariwise will control the domes directly ,Parallel connect the key board and dome to the bus of RS-485,all the key board can control any dome amon g them, under this way, the add of the main key board should be “1”...
3. Keyboard operation instruction LCD screen lens control 3D joystick Number keys Function keys Figure 3-1.1 Attention p lease because differ ent sy stem have some diff erent sp ecial op eration way s, so should consider the actual requir ement when op eration in some sp ecial sy stems 3.1 Electrify When the p ower is on, the key board will automatically check the baud rate、p rotocol of the key board、aim dome and the aim monitor, and all the info.
3. 3 Joystick Controls Dome Functions of the Joystick: Dome rotation control and Object dome menu setup 。 ●When op erate the joy stick at will to any direction Dome will rotate at the same direction ,and the direction will be disp lay ed below right corner as When for menu setup ,...
●design p ath setup : 【SET】+【N 】+【PATTERN】+p ath+【SET】+ 0 +【 PATTERN】 Press【SET】key ,inp ut the number of design scan(1-4) ,p ress【PATTERN】key ,enter the p ath setup state, when endin g p ress 【SET】key first,then p ress【0】key ,then 【PATTERN】key , ●starting the design scan: 【N】+【PATTERN】inp ut the design scan nu mber(1-4) ,p ress【PATTERN】key to starting,...
‘ Picture 4.1-1 ● Save the setting After setting the function y ou need, p ress【ENTER】to save the setting. After finishing the setting, the TFT will disp lay “Success”. ● Back to Previous menu Press the【PREV】key to back to the p revious menu. 4.1 Keyboard parameter setting 4.1.1 Keyboard ID set up 1、Enter the main menu...
Picture 4.1.1-6 5、Press 【PREV】or use the shake toward to LEFT to back to p revious menu. Warning :: The camera ID def ault is 1. only one key board in a sy stem, it must set to ID as “1”. Sever al key boards work together at most is 4 key boards, and it must has one key board ID is ID1, otherwise all the key board can not work.
Picture4.1.3-2 Attention: when calibratin g the joy stick, p ls make sure the joystick is in the midp oint p osition 4.1.4 Keyboard information display Enter the key board information disp lay menu as LCD(Picture 4.1.1-2) Press【2】to check the key board information as LCD(Picture 4.1.4-1) 4.2 Dome set up 4.2.1 Preset set up Enter the main menu as p icture (4.1.1-1)...
Press【2】enter the “Show the p reset ” menu as p icture 4.2.1-5 Preset num: (1-128) Press PREV to back Picture 4.2.1-5 Inp ut the Preset NO that want delete, and p ress the 【ENTER】to call it, and the T FT will disp lay“Success" . Use the navigate Key or 【PREV】...
4.2.3 Pattern set up Enter the menu as the p icture (4.1.1-1) Press【2】 enter the dome setting menu as the p icture (4.2.1-1); And then p ress【3】 enter the p attern setting as p icture 4.2.3-1 show 1. Pattern num: 2.
Press【3】Run the TOUR Attent ion: This model have no the insert tour p reset function 4.3 Protocol set up Enter the menu as p icture (4.1.1-1), Press 【3】enter the Protocol setting as p icture (4.3-1) 1. Matrix/DVR 2. Dome Picture 4.3-1 4.3.1 Pelco Matrix model Press【1】...
Page 15
follow based on the different Baud rate: Baud rate Farthest Distance 2400bp s 1800M 4800bp s 1200M 9600bp s 800M 19200bp s 600M If us er s elects thinner cables , or ins talls the dome in an environ ment with s trong electromagnetic interference, or connects lots of equipment to the RS485 Bus , the ma ximu m trans mitting dis tance will be decreas ed.
120Ω M ain Controller 15 # 120Ω Picture 4-1.3 120Ω 120Ω 120Ω Picture 4-1.4 Keyboard shortcut o peration manual Working Mode shortcut Operation object Function Press 【 SET】 for 2 seconds Keybo ard IR remote ON/OFF Press 【MENU】for 2 Enter the system setting Keybo ard seconds Input Dome ID, press 【CAM】to...
Page 17
Input preset ID, press【Preset】to 【N】+ 【PRESET】 High speed dome call the preset 【SHI】+【1】+【ENT】 High speed dome ON/OFF w ater Wiper 【SHI】+【2】+【ENT】 High speed dome ON/OFF auxiliary light Ad just image to object position, press Set to input 【SET】 + 【1】 + 【SCAN】 High speed dome 【1】...