Table of Contents
Advertisement
Regarding t h e Lamp ( C ont i n
4
Remov e t h e lamp u n it .
¥ Loo s e n t h e s e c u r ing s c re w s from t h e
lamp u n it . Hold t h e lamp u n it by t h e
handle and p u l l i t in t h e direc t i on of t h e
arro w . A t t h i s t i me , keep t h e lamp u n i t
hori z o n t a l and do no t t i l t i t .
5
Ins e rt t h e new lamp u n it .
ng the Projector Function ("PRJ - ADJ" menu)
¥ Pre s s t h e lamp u n i t firml y in t o t h e lamp
u n i t compar t m en t . Fa s t e n t h e s e c u r ing
s c re w s .
Picture
6
1
Auto Search
Replace t h e lamp u n it cov e r.
2
Auto Sync
¥ Align t h e t a b on t h e lamp u n it cov e r
3
Auto Power Off
(
) a nd place i t w h ile pre s s i ng t h e t a b
4
System Sound
(
) t o clo s e i t . Then t i gh t e n t h e u s e r s e r -
5
Speaker
6
RS-232C
v i ce s c rew t o s e cu r e t h e lamp u n it cov e r.
7
Fan Mode
8
Lamp Timer(Life)
¥ If t h e lamp u n i t and lamp u n i t co v e r are
SEL./ADJ.
not correct l y ins t a lled, t h e pow e r w i ll not
t u r n on , e v e n if t h e po w e r cord i s con -
Search Function
nec t e d t o t h e projec t o r .
automatically searches for and
e input mode in which signals are
, when the projector is turned on,
Res e t t i ng t h e Lamp Timer
PUT button is pressed.
Reset the lamp timer after replacing the lamp.
earch" is set to "On"
input signals are found, the pro-
Info
the input source in the order of
¥ Make s u r e t o re s e t t h e lamp t i mer onl y w h en
NPUT 2 n INPUT 3 n INPUT 4
replacing t h e lamp. If y o u res e t t h e lamp t i mer
ss INPUT (P/R) on the projector.
and con t i n u e t o u s e t h e s a me lamp , t h i s ma y
Search" is set to "On", press
ca u s e t h e lamp t o become damaged or e x -
,C INPUT 2, D INPUT 3 or
plode .
on the remote control to select
e other than the input mode se-
projector.
1
Connect t h e pow e r cord.
¥ Pl u g t h e po w e r cord in t o t h e AC s o cke t
Sync (Auto Sync
of t h e projec t o r .
stment)
2
Res e t t h e lamp t i mer.
ms
Description
¥ While s i mu l t a neou s l y holding dow n
UMENU / H ELP ,
Auto Sync adjustment will
occur when the projector is
projec t o r , pre s s
turned on or when the input
projec t o r .
signals are switched, when
¥ Ò L AMP 0 0 0 0 H Ó i s di s p la y e d , indica t i ng
connected to a computer.
t h a t t h e lamp t i mer i s re s e t .
Auto Sync adjustment is not
Downloaded from ProjectorsManual.com Manuals
5 2
automatically performed.
SCR - ADJ
PRJ - ADJ
Off
On
On
Off
On
9600 bps
Normal
Info
0
h
ENTER
3 Auto Power Off
3
3
3
3
Function
Selectable
items
On
Off
Note
• When the Auto Power Off function is set to
"On", 5 minutes before the projector enters
standby mode, the message "Enter STANDBY
mode in X min." will appear on the screen to
indicate the remaining minutes.
TENTER and
SSTANDBY / O N on t h e
Secu r ing s c rew s
Menu operation n Page 39
Help
100%
END
Description
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
The Auto Power Off function will be
disabled.
AC s o cket
R on t h e
Handle
2
1
STANDBY/ O N
bu t t o n
ENTER bu t t o n
MENU/ H ELP
bu t t o n
R bu t t o n
Advertisement
Table of Contents
Troubleshooting
