Advertisement
QuickSpecs
Configuration Information - Factory Integrated Models
Select one or two processors from Core options-Processor section below,
If one processor is desired, select one xxxxxx-L21
If two processors are desired, select one xxxxxx-L21 and one xxxxxx-B21.
Up to 2 processors supported. Mixing different processor models is not supported.
DDR4 speed is the maximum memory speed of the processor. Actual memory speed may depend
on the quantity and type of DIMMs installed.
For the Intel® C610 Chipset E5-4600 Series, the letter preceding the model number indicates the
Product Line (E5); 4600x v#, 4 = number of CPUs in a Node, 6 is socket/segment designation, 00 =
Processor SKU, x = L for low power SKUs and v# (not yet designated) = version number.
Select one or more memory from Core options-Memory section below,
LRDIMM, RDIMM are all distinct memory technologies and cannot be mixed within a server. The
majority of ProLiant Gen9 servers support LRDIMM and RDIMM.
HPE memory from previous generation servers are not qualified or warranted with this HPE
ProLiant Server. HPE SmartMemory is required to realize the memory performance improvements
and enhanced functionality listed in this document for Gen9.
If only one processor is installed, only half of the total DIMM slots are available. When populating
with two processors all DIMM slots are available.
Kits described as LP include Low Power DIMMs. For more information on ProLiant Energy Efficient
Features, see: http://www.hp.com/go/proliant-energy-efficient.
Depending on the memory configuration and processor model, the memory speed may run at 2400,
2133MHz, 1866MHz, 1600MHz or 1333MHz. Please see Memory Population Table or the Online
Memory Configuration Tool at:
Select one or more power supplies from Core Options-Power Supplies section below:
Prior to selecting a power supply option, it is highly recommended that you review your server
configuration in the HPE Power Advisor tool to determine the right size power supply for your server
configuration. The HPE Power Advisor is located at: http://www.hp.com/go/hppoweradvisor.
Mixing of power supplies in the same server is not supported. All power supplies must be of the
same input voltage, output rating, and efficiency rating. If non-matching power supplies are
installed, you may receive an error message and/or experience operational issues with your server.
Step 3: Choose Additional Factory Integratable Options
Select one or more Unique options from Core options section below.
This section may contain FIO options, please see the Unique options section below.
FIO indicates that this option is only available as a factory installable option.
Select one or more Riser Kit options from Core options section below.
To take advantage of the additional PCI slot upgrade, the second processor must be installed.
This section may contain FIO options, please see HPE I/O Expansion Options section below.
FIO indicates that this option is only available as a factory installable option.
Select one or more drives from Core options-HPE Drives section below:
The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the
server backplane) should operate at the same data transfer rate or the system bandwidth will be
negotiated down to an acceptable level for all components.
Hard drives have either a one year or three year warranty; refer to the specific hard drive
QuickSpecs for details.
The HPE ProLiant Gen9 Smart Storage solutions are equipped with re-designed Small Form Factor
(SFF 2.5 in) and Large Form Factor (LFF 3.5 in) hot plug carriers for HPE Qualified Hard Drives
and Solid State Drives. These new carriers provide status and activity indicators as well as caution
indicators for "Do Not Remove".
Select a FlexibleLOM from Core options-Networking section below,
http://www.hp.com/go/ddr4config.
DA - 15296 Worldwide QuickSpecs — Version 10 — 6.20.2016
HPE ProLiant DL560 Generation9 (Gen9)
Page 21
Advertisement
