Epson ELPMC02 User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Microphone
  5. ELPMC02
  6. User manual
Epson ELPMC02 User Manual

Epson ELPMC02 User Manual

Pendant microphone kit
Hide thumbs Also See for ELPMC02:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
ELPMC02
Pendant Microphone Kit
User's Guide
Installing the IR Receiver
Installing the IR Dome Sensor
Pendant Microphone Set Up
Solving Problems
Notices and Warranty

Advertisement

Table of Contents
loading

Related Manuals for Epson ELPMC02

Summary of Contents for Epson ELPMC02

  • Page 1 ELPMC02 Pendant Microphone Kit User’s Guide Installing the IR Receiver Installing the IR Dome Sensor Pendant Microphone Set Up Solving Problems Notices and Warranty...

  • Page 2: Table Of Contents

    Epson America, Inc. Limited Warranty ........

  • Page 3: Introduction

    ■ Epson accepts no responsibility for any of the components of this product falling due to the lack of strength of the ceiling or inadequate installation.
  • Page 4 ■ Make sure all the bolts, screws, and nuts are tight once the installation is finished. There is a risk of the system falling and it could cause severe injury if any of the hardware is loose. ■ Be aware of the neck strap when using the pendant microphone. The neck strap may snap off if handled roughly.

  • Page 5: Parts List

    ■ Turn off the microphone power after use. Parts List Before starting, make sure you have all the parts listed below. If you’re missing any parts, contact Epson as described on page 16. Pendant microphone Neck strap AA alkaline batteries...

  • Page 6: Getting Started

    Getting Started Before you can use your pendant microphone, you need to do the following: ■ Install the IR receiver module ■ Install and connect the IR dome sensor ■ Attach the neck strap ■ Insert the batteries ■ Adjust the sound Install the IR Receiver Module Follow the steps below to install the IR receiver module.

  • Page 7: Install The Ir Dome Sensor

    Coaxial cable Warning: Make sure that the ceiling is strong enough to support the IR dome sensor and coaxial cable. Epson accepts no responsibility for the IR dome sensor falling due to insufficient ceiling strength or inadequate installation. Getting Started...

  • Page 8: Attach The Neck Strap

    Bend both ends of the mounting bracket as shown below. Securely attach the IR dome sensor to the ceiling. Installation varies depending on your building construction. Attach the coaxial cable to the back of the IR dome sensor. Secure the coaxial cable to the ceiling. Note: The coaxial cable can also be run in the ceiling instead of securing it to the ceiling.

  • Page 9: Insert Batteries

    Reconnect the ends of the neck strap. Insert Batteries If the power button on the pendant microphone turns red or doesn’t illuminate, you may need to insert or replace the batteries. Follow the steps below to insert batteries in the pendant microphone.
  • Page 10 Adjust the neck strap so that the top of the microphone is just below your collarbone. Set the switch to Channel Note: The channel must be set to 1 when the microphone is used with the Connection & Control Box. Channel 2 is not available. Emitter Press the power button until it clicks into place.

  • Page 11: Connecting External Audio Devices

    Speak normally into the microphone and gradually increase the gain control knob on the IR receiver IR receiver gain control module. knob 10. Now you can adjust the volume control on the Connection & Control Box. Note: If necessary, you can also adjust the volume on the speakers and any other audio sources that are connected.
  • Page 12 If you need to adjust the volume, use your external audio device’s volume control. Note: If your audio device doesn’t have a volume control, you can use the microphone Gain control wheel to adjust the volume from your external audio device.

  • Page 13: Solving Problems

    Solving Problems If you have a problem with your pendant microphone kit, check the following sections for basic troubleshooting suggestions. Problems and Solutions There is no sound ■ If you can’t hear audio from the microphone, make sure that the Gain control wheel on the pendant microphone is set so that the white line is next to Up, but still visible.

  • Page 14: Specifications

    External audio devices are too loud ■ Use the volume control on the external audio device to decrease the volume of the external audio device. ■ Adjust the audio levels, see page 9 for details. I hear feedback (howling) ■ Move the pendant microphone away from the speakers.
  • Page 15 IR dome sensor Input Voltage DC 24 V (draws power from IR receiver) Size 4.0" × 1.2" (10.1 × 3 cm) (not including connector) Weight 6.17 ounces (175 g) Temperature Operating: 41 °F to 95 °F (5 °C to 35 °C) Humidity Operating: 20% - 80% Cable (coaxial)

Table of Contents