Using As A Controller For Other Dj Software; About Trademarks And Registered Trademarks - Pioneer DDJ-WEGO4 Operating Instructions Manual

Problem
Sound is not output from the [MIC]
input terminal.
There is no response when the jog dial
is touched.
The iPhone / iPad cannot be
recharged.
[STANDBY/ON] indicator is flashing.
Noise occurs in the sound.
Using as a controller for other DJ
software
This unit also outputs the operating data for the buttons and controls in
MIDI format. If you connect a computer with a built-in MIDI-compatible
DJ software via a USB cable, you can operate the DJ software on this
unit. The sound of music files being played on the computer can also be
output from the DDJ-WEGO4.
Set the DJ software's audio and MIDI related settings.
For details, see your DJ software's operating instructions.
About MIDI messages
For details on this unit's MIDI messages, see "List of MIDI Messages".
! "List of MIDI Messages" can be obtained from [MIDI-compatible
software] of [SOFTWARE INFORMATION] of [DDJ-WeGO4] on the
Pioneer DJ support site below.
http://pioneerdj.com/support/
About trademarks and registered
trademarks
! "Pioneer DJ" is a trademark of PIONEER CORPORATION, and is used
under license.
! rekordbox and WeDJ are registered trademarks or trademarks of the
Pioneer DJ Corporation.
! djay and vjay are trademarks of algoriddim GmbH.
! Windows is a registered trademark of Microsoft Corporation in the
United States and other countries.
Check
Is the [MIC ON] button in the microphone panel of
rekordbox off?
Is the jog dial dirty?
Does the jog dial respond when touched while
touching some other metal part of the unit?
Are you using the unit on USB bus power?
Is the charging mode of this unit set to "Charging
is possible when the power is on only" and is the
[STANDBY/ON] indicator red?
Is a computer connected?
Is the iPhone / iPad power supply off?
Is the iPhone / iPad battery residual power
exhausted?
Is the [STANDBY/ON] indicator flashing?
—
—
Remedy
Turn the [MIC ON] button in the microphone panel of rekordbox on.
An electrostatic system is used as the detection method in the jog dial of this
unit. Therefore, if the jog dial is dirty or the user has hand cream on their hands,
detection may not respond. When cleaning the jog dial, dry wipe with a soft
cloth. If it is very dirty, prepare a 5:1 or 6:1 solution of water and neutral deter-
gent, immerse a soft cloth in the solution and wring out well, then clean the jog
dial and wipe with a dry cloth after that.
If there is a response when touching the jog dial while touching some other
metal part of the unit, there is a possibility that the unit is being affected by a
device connected to the unit. Review the connection environment (installation
location, ground connection status, etc.) of the devices (computer, amplifier,
etc.) connected to this unit.
Only when the unit is connected to an AC adapter, the iPhone / iPad can be
recharged.
Connect the unit and the AC adapter, and then connect the iPhone / iPad.
If the charging mode of this unit is set to "Charging is possible when the power
is on only," the iPhone / iPad can be charged when the [STANDBY/ON] indica-
tor is green. If the charging mode is set to "Charging is always possible," the
iPhone / iPad can be charged when the [STANDBY/ON] indicator is green and
when it is red.
Disconnect the computer.
If the iPhone / iPad power supply is off, iPhone / iPad recharging cannot be
performed.
Turn on the iPhone / iPad power supply, and connect to the unit.
If the iPhone / iPad battery residual power is exhausted and the power supply
cannot be turned on, iPhone / iPad recharging cannot be performed.
Use the battery charger included in the iPhone / iPad to recharge the iPhone /
iPad, turn on the power supply and then connect to the unit.
Temporarily disconnect the connected iPhone / iPad, and check the connection
cable.
If operation is abnormal, or it won't start up, disconnect the AC adapter or USB
cable, wait for a little while, and then restart again.
If the symptoms still appear, put in a request for repairs.
When engaged in voice conversation or data transfer or receiving on the iPhone
/ iPad, sound interruptions (communication noise) may occur in the unit. If
these symptoms occur, change the iPhone / iPad install location or orientation.
If this still does not improve the symptoms, turn off the iPhone / iPad mobile data
communications and use the Wi-Fi connection or turn on the flight mode.
! iPhone, iPad, iPad Air, iPod touch, Finder, Mac and Mac OS are
trademarks of Apple Inc., registered in the U.S. and other countries.
! iPad mini and iPad Pro are trademarks of Apple Inc.
! App Store is a service mark of Apple Inc.
! "Made for iPod," "Made for iPhone," and "Made for iPad" mean
that an electronic accessory has been designed to connect specifi-
cally to iPod, iPhone, or iPad, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is
not responsible for the operation of this device or its compliance
with safety and regulatory standards. Please note that the use
of this accessory with iPod, iPhone, or iPad may affect wireless
performance.
! iOS is a trademark on which Cisco holds the trademark right in the
US and certain other countries.
! Intel and Intel Core are trademarks of Intel Corporation in the U.S.
and/or other countries.
The names of companies and products mentioned herein are trade-
marks or registered trademarks of their respective owners.
37
En