Page 1
CD-350S AUG. 2001 MULTI FUNCTION DISPLAY COMPACT DIGITAL AUDIO POWER MEMORY RANDOM/REMAIN REPEAT/PRESET BAND STOP/ PLAY EJECT PAUSE Model-B Model-C Model-G Argentina Model-E Other Countries CD CASSETTE SYSTEM INDEX...
SPECIFICATIONS CD PLAYER Type .............. Compact disc player with optical pick up Number of channels ........2 (stereo) Frequency response ........20 Hz - 20 kHz, ± 3 dB Dynamic range ..........70 dB Total harmonic distortion ....... 0.1 % (1 kHz) S/N ratio ............
LCD DISPLAY FM ANT. AM ANT. LAMP KEY CONTROL 10V 40mA X3 DOOR SWITCH FM RF. AM OSC. CF701 75KHz LAMP CONTROL SLT. SWITCH L102 T103 U-COM Q406 IC101 IC701 DISC MOTOR TC9314F-043 TA2104AN MOTOR AND REGULATOR ACTUATOR FM OSC. DRIVER Q120 L103...
ADJUSTMENTS CASSETTE MECHANISM General Remarks • Before attempting to adjust the mechanism, wipe clean all tape-contacting surfaces (pinch roller, REC/PB head, erase head, and capstan), as well as the contact surfaces of the driving parts (motor pulley, flywheel, pulley, belt, and clutch assembly), with a piece of soft cloth moistened with denatured alcohol. Grease stains may cause trouble.
Page 7
Tape Speed Adjustment (Figures 3 and 4) Step Setting Adjust Result Play the test tape Motor screw Frequency counter reading should be (MTT-111N) (Figure 4) 3000 Hz (2940 ~ 3060). Frequency Counter 3000 Headphone Jack Figure 3 Motor Screw Figure 4 —...
TUNER General Remarks • When aligning the range and adjusting tracking, proceed with alignment in a sequence of AM--FM. • Use a screwdriver with a plastic grip for all alignments. Equipment Required • AM signal generator (AM SG) • Loop antenna •...
Page 9
FM IF Alignment (Figures 6) Frequency of Tuning dial Step Alignment Adjustment Remarks signal generator setting IF calibration 10.7 MHz 98.1 MHz (Non- Obtain sine-wave and adjustment) maximum amplitude Max. FM Alignment (Figures 6) Frequency of Tuning dial Step Alignment Adjustment Remarks signal generator...
CD TROUBLESHOOTING Open the CD door and set the function switch for CD position. Is “00” display on LCD? (See page9) Load a disc and close the CD door. Is total track number displayed? (See page9) Press “ ” button. Is the audio signal present at the output (See page16)
Page 11
1. At power on, “00” is not displayed. Is + 5V lines Check Q903. normal (for IC902)? Check pins 26 and 58.59.77 of IC901. Does Check X901. 16.93MHz clock pulse appear Check circuit around X901 and IC901. at pin 78/79 of IC901? Check soldering and circuit around IC901.
Page 12
Note : Open the CD door and set the door switch for “on” position. Check the radiation power with an optical power meter or by watching the radiation through the lens or the pickup unit at a minimum distance of 30cmfrpm the from pickup. Does the Laser emit? (See page11) Does the lens...
Page 13
2-A1 Is Q901 emitter 5V? Check Q901. (Play) Is waveform Check circuit around at pin 21 (SEL) of IC902 like that IC901 and IC902 (SEL). shown in figure 10? Is waveform Check circuit around at base of Q901 like that pins 21 and 45 of IC901.
Page 14
2-A2 Is Q403 Check circuit around Q403. emitter 8V? Is waveform Check circuit around pin 16 (FSO) of IC902. at C964 4.7UF (FSO) like that shown in figure 12? IC902 is defective. waveform at pins 21 to 23 Check circuit around pins 20~23 of IC903.
Page 15
Does the disc motor rotate? (See page14) Is waveform at pin 24 (DMEO) of IC902 like that shown in figure 14? Check circuit around pin 24 of IC902. Is waveform at pins 14 to 16 of IC903 like that Check circuit around pins 14 to 16 of IC903.
Page 16
2-B1, B2 Is PSET switch circuit normal? Does gear and mechanism of disc motor Is waveform at operate normally? (See page15) pin 54 PU-INNER of IC701 like that shown in figure 16? Is waveform at pin 26 (FMSO) of IC902 like that Check PU-INNER switch.
Page 17
2-B3 Is waveform Check circuit around pins 1~5 at pin 1(RFO) of IC902 like that and 41~44 of IC902. shown in figure 19? Is waveform at pin 35 (TSO) of IC902 like that shown in figure 20? Check circuit around pins 30~40 of IC902.
Page 18
3. No present at R939 (R ch) and R940 (L ch) audio signal. Does audio signal appear at pins 1 and 8 Check circuit around pins 1~8 of IC904. of IC904? Check pins 1~7 of IC901. — 16 —...
Page 19
4. Selected music cannot be searched smoothly. Press the play key. (PAUSE) Check 100mV PP waveform at pins Is waveform 3 and 8 of CN901. at pin 35 (TSO) of IC902 like that Check pins 4 and 5 of IC901. shown in figure 23? Check pickup.
PARTS LIST CD-350S Notes: 1. Prices and specifications are subject to change without pointer notice. 2. As for spare parts order and supply, refer to the “GUIDEBOOK for Spare parts Supply”, published separately. 3. The numbers in item column correspond to the same numbers in drawing.