Step 1 Connection - Panasonic Diga DMR-EX79 Operating Instructions Manual

1
STEP
≥Before connection, turn off all equipment and read the appropriate operating instructions.
≥Refer to "Additional connections" (
When the unit is not to be used for a long time
To save power, unplug it from the household
mains socket. This unit consumes a small
amount of power, even when it is turned off
[approx. 2 W ("Power Save" is set to "On")]
Connecting a television
≥Connect to terminals of the same colour.
To the aerial
RF coaxial cable
(included)
2
1 2
Aerial cable
You can enjoy high-quality picture by changing the connection between this unit and your TV as follows.
Connecting to a TV with an HDMI (High Definition Multimedia Interface) cable
When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted. You can enjoy high quality, digital
video and audio with just one cord. When connecting to an HDMI-compatible HDTV (High Definition Television), the output can be switched to
1080p, 1080i or 720p HD video.
≥This unit incorporates HDMI
≥Video sources converted to 1920k1080 resolution, while of high quality, will exhibit somewhat lower subjective image resolution than true,
native 1080p full-HD sources. See dealer for details.
≥Please use High Speed HDMI Cables that have the HDMI logo (as shown on the cover).
≥When setting video output to "1080p", please use the HDMI cables 5.0 meters or less.
Regarding VIERA Link "HDAVI Control
When connecting with a Panasonic TV (VIERA) or a receiver equipped with the "HDAVI Control" function, linked operations would be possible.
[ 36, Linked operations with the TV (VIERA Link "HDAVI Control
≥Non-HDMI-compliant cables cannot be utilised.
≥It is recommended that you use Panasonic's HDMI cable.
Recommended part number:
RP-CDHG10 (1.0 m), RP-CDHG15 (1.5 m), RP-CDHG20 (2.0 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m), etc.
Required setting
≥Set "Digital Audio Output" to "HDMI and
Optical" ( 63).
(The default setting is "HDMI and Optical".)
RF RF
Y
IN IN
P
B
P
RF RF OPTICAL R
OUT OUT
DIGI T T AL AL A A UDIO OU DIGI UDIO OU T T COMPONENT COMPONENT
(PCM/BITSTREAM) (PCM/BITSTREAM) VIDEO OUT VIDEO OUT
Note
≥If you are connecting to a TV that is only compatible with 2 channel audio output, audio with 3 channels or more will be down mixed (
output as 2 channels, even if connecting with an HDMI cable. (Some discs cannot be down mixed.)
≥You cannot connect this unit to DVI devices that are incompatible with HDCP.
For units compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection that are equipped with a digital DVI input
terminal (PC monitors, etc.):
RQT9306
Depending on the unit, images may not be displayed properly or at all when connecting with a DVI/HDMI switching cable. (Audio cannot be
8
output.)
Connection
66) for connection using other terminals and connection with other equipment.
VHF/UHF
RF IN
Other connections
( below, 66)
RF RF
Y
IN IN
P
B AV1
( TV )
P
RF RF OPTICAL R
OUT OUT
DIGI DIGITAL AL AUDIO OU UDIO OUT COMPONENT COMPONENT
(PCM/BITSTREAM) (PCM/BITSTREAM) VIDEO OUT VIDEO OUT AV2 ( EXT )
(V.1.3a with Deep Colour) technology.
TM
TM " function
A V 1
( TV )
R- A UDIO- L VIDEO
AV2 ( EXT )
Connecting to a television with 21-pin Scart terminal
You can also connect with the AV1 terminal on this unit using the 21-pin Scart cable.
≥If your television is equipped with RGB input capability, by connecting with a fully
wired 21-pin Scart cable you can see video using RGB output on this unit.
"AV1 Output" in the Setup menu (
Required setting
Television's rear panel
AUDIO IN VIDEO IN
R L
Audio/Video cable
(included)
3
R-AUDIO-L VIDEO S-VIDEO AV OUT
")]
TM
Television's rear panel
HDMI IN
HDMI cable
HDMI AV OUT
AV OU V OUT
S-VIDEO
63)
To household mains socket
(AC 220 to 240 V, 50 Hz)
AC mains lead
(included)
Connect only after all other
connections are complete.
Cooling fan
This unit's rear panel
This unit's
A C IN rear panel
4
AC IN
81) and