Protecting The Environment - Black & Decker VPX1201 User Manual

Driving screws
When driving screws, the forward/reverse button (4)
should be pushed to the left.
Move the forward/reverse button (4) pushed to the right
for removing screws.
Drilling
Use sharp drill bits only.
Support and secure the work properly.
Run the drill very slowly, using light pressure, until the
hole is started.
Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
Hold the drill firmly with two hands to control its twisting
action.
Do not click the trigger of a stalled drill on and off in an
attempt to start it. Damage to the drill can result.
Minimize stalling on breakthrough by reducing pressure
and drilling slowly through the last part of the hole.
Keep the motor running while pulling the bit out of a
drilled hole. This will help reduce jamming.
With variable speed drills there is no need to centre
punch the point to be drilled. Use a slow speed to start
the hole and accelerate by squeezing the trigger harder
when the hole is deep enough to drill without the bit
skipping out. Operate at full speed after starting the bit.
Drilling wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes of the drill.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil or
lard oil.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
Run the battery down completely, then remove it from
the tool.
Lithium Ion batteries are recyclable. Take them to any
authorised repair agent or a local recycling station.
Technical data
Voltage
No load speed
Power source
Max drilling size, wood & metal
Spindle lock torque
Output torque (max)
Charger
Battery
Weight (bare unit)
ENGLISH
VPX1201
Vdc 7
rpm 195/625
TM
1 VPX battery
pack
mm 6
kgf/cm 110
Nm 17
type single port
TM
type VPX battery
pack
kg 0.62
7